WLE600VX from PCEngines
Tomasz Skapski
tomasz.skapski at tieto.com
Tue Sep 8 21:10:35 PDT 2015
Sending again as a plain text.
Regards,
Tomasz Skąpski
On 8 September 2015 at 21:03, Tomasz Skapski <tomasz.skapski at tieto.com> wrote:
> Hi Marcel,
>
> you are using iw set freq command in a wrong way. You have to also inform
> about the center frequency to use in case of 80 MHz bandwidth. Try this:
>
> iw wlan0 set freq 5745 80 5775
>
> Regards,
> Tomasz Skąpski
>
> On 8 September 2015 at 14:31, Marcel H. <maco at blava.net> wrote:
>>
>> Hi everyone,
>> I have an interesting issue - I'm trying to run the QCA9882 based card
>> in IBSS mode (to be used for BATMAN), however all I can do is to run
>> in in 40Mhz channel width in 5GHz spectrum. Any attempt to run it in
>> 80MHz width resolves in the following:
>>
>> Interface wlan0
>> ifindex 5
>> wdev 0x1
>> addr 04:f0:21:1b:5f:3b
>> ssid my-mesh-network
>> type IBSS
>> wiphy 0
>> channel 157 (5785 MHz), width: 40 MHz, center1: 5795 MHz
>> root at voyage2:/opt/ca_node/bin# iw dev wlan0 set freq 5745 80
>> command failed: Invalid argument (-22)
>> root at voyage2:/opt/ca_node/bin# ip link set wlan0 down
>> root at voyage2:/opt/ca_node/bin# iw dev wlan0 set freq 5745 80
>> command failed: Invalid argument (-22)
>>
>>
>> More info:
>> =====================================================
>> 06:00.0 Network controller: Qualcomm Atheros QCA988x 802.11ac Wireless
>> Network Adapter
>> Flags: bus master, fast devsel, latency 0, IRQ 27
>> Memory at f7400000 (64-bit, non-prefetchable) [size=2M]
>> Expansion ROM at f7600000 [disabled] [size=64K]
>> Capabilities: [40] Power Management version 2
>> Capabilities: [50] MSI: Enable+ Count=1/8 Maskable+ 64bit-
>> Capabilities: [70] Express Endpoint, MSI 00
>> Capabilities: [100] Advanced Error Reporting
>> Capabilities: [140] Virtual Channel
>> Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00
>> Kernel driver in use: ath10k_pci
>>
>> root at voyage2:/opt/ca_node/bin# iw reg get
>> country US: DFS-FCC
>> (2402 - 2472 @ 40), (N/A, 30), (N/A)
>> (5170 - 5250 @ 80), (N/A, 17), (N/A)
>> (5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS
>> (5735 - 5835 @ 80), (N/A, 30), (N/A)
>> (57240 - 63720 @ 2160), (N/A, 40), (N/A)
>>
>>
>> root at voyage2:/opt/ca_node/bin# uname -a
>> Linux voyage2 4.2.0-wl-ath-261216-gd89281c #1 SMP Tue Sep 8 14:03:33
>> GMT 2015 i686 GNU/Linux
>> (todays checkout from https://github.com/kvalo/ath + Voyage Linux 0.10
>> .config)
>>
>> root at voyage2:/lib/firmware/ath10k/QCA988X/hw2.0# md5sum ./firmware-2.bin
>> e2db04b651c2b5ced4732f3f009a1cce ./firmware-2.bin
>> (this is from the 'main' directory in the
>> https://github.com/kvalo/ath10k-firmware)
>>
>>
>> Wiphy phy0
>> max # scan SSIDs: 16
>> max scan IEs length: 195 bytes
>> Retry short limit: 7
>> Retry long limit: 4
>> Coverage class: 0 (up to 0m)
>> Device supports RSN-IBSS.
>> Device supports AP-side u-APSD.
>> Supported Ciphers:
>> * WEP40 (00-0f-ac:1)
>> * WEP104 (00-0f-ac:5)
>> * TKIP (00-0f-ac:2)
>> * CCMP (00-0f-ac:4)
>> * CMAC (00-0f-ac:6)
>> Available Antennas: TX 0x3 RX 0x3
>> Configured Antennas: TX 0x3 RX 0x3
>> Supported interface modes:
>> * IBSS
>> * managed
>> * AP
>> * AP/VLAN
>> * monitor
>> * P2P-client
>> * P2P-GO
>> * P2P-device
>> Band 1:
>> Capabilities: 0x19e3
>> RX LDPC
>> HT20/HT40
>> Static SM Power Save
>> RX HT20 SGI
>> RX HT40 SGI
>> TX STBC
>> RX STBC 1-stream
>> Max AMSDU length: 7935 bytes
>> DSSS/CCK HT40
>> Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
>> Minimum RX AMPDU time spacing: 8 usec (0x06)
>> HT TX/RX MCS rate indexes supported: 0-15
>> VHT Capabilities (0x338001b2):
>> Max MPDU length: 11454
>> Supported Channel Width: neither 160 nor 80+80
>> RX LDPC
>> short GI (80 MHz)
>> TX STBC
>> RX antenna pattern consistency
>> TX antenna pattern consistency
>> VHT RX MCS set:
>> 1 streams: MCS 0-9
>> 2 streams: MCS 0-9
>> 3 streams: not supported
>> 4 streams: not supported
>> 5 streams: not supported
>> 6 streams: not supported
>> 7 streams: not supported
>> 8 streams: not supported
>> VHT RX highest supported: 0 Mbps
>> VHT TX MCS set:
>> 1 streams: MCS 0-9
>> 2 streams: MCS 0-9
>> 3 streams: not supported
>> 4 streams: not supported
>> 5 streams: not supported
>> 6 streams: not supported
>> 7 streams: not supported
>> 8 streams: not supported
>> VHT TX highest supported: 0 Mbps
>> Bitrates (non-HT):
>> * 1.0 Mbps
>> * 2.0 Mbps (short preamble supported)
>> * 5.5 Mbps (short preamble supported)
>> * 11.0 Mbps (short preamble supported)
>> * 6.0 Mbps
>> * 9.0 Mbps
>> * 12.0 Mbps
>> * 18.0 Mbps
>> * 24.0 Mbps
>> * 36.0 Mbps
>> * 48.0 Mbps
>> * 54.0 Mbps
>> Frequencies:
>> * 2412 MHz [1] (30.0 dBm)
>> * 2417 MHz [2] (30.0 dBm)
>> * 2422 MHz [3] (30.0 dBm)
>> * 2427 MHz [4] (30.0 dBm)
>> * 2432 MHz [5] (30.0 dBm)
>> * 2437 MHz [6] (30.0 dBm)
>> * 2442 MHz [7] (30.0 dBm)
>> * 2447 MHz [8] (30.0 dBm)
>> * 2452 MHz [9] (30.0 dBm)
>> * 2457 MHz [10] (30.0 dBm)
>> * 2462 MHz [11] (30.0 dBm)
>> * 2467 MHz [12] (disabled)
>> * 2472 MHz [13] (disabled)
>> * 2484 MHz [14] (disabled)
>> Band 2:
>> Capabilities: 0x19e3
>> RX LDPC
>> HT20/HT40
>> Static SM Power Save
>> RX HT20 SGI
>> RX HT40 SGI
>> TX STBC
>> RX STBC 1-stream
>> Max AMSDU length: 7935 bytes
>> DSSS/CCK HT40
>> Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
>> Minimum RX AMPDU time spacing: 8 usec (0x06)
>> HT TX/RX MCS rate indexes supported: 0-15
>> VHT Capabilities (0x338001b2):
>> Max MPDU length: 11454
>> Supported Channel Width: neither 160 nor 80+80
>> RX LDPC
>> short GI (80 MHz)
>> TX STBC
>> RX antenna pattern consistency
>> TX antenna pattern consistency
>> VHT RX MCS set:
>> 1 streams: MCS 0-9
>> 2 streams: MCS 0-9
>> 3 streams: not supported
>> 4 streams: not supported
>> 5 streams: not supported
>> 6 streams: not supported
>> 7 streams: not supported
>> 8 streams: not supported
>> VHT RX highest supported: 0 Mbps
>> VHT TX MCS set:
>> 1 streams: MCS 0-9
>> 2 streams: MCS 0-9
>> 3 streams: not supported
>> 4 streams: not supported
>> 5 streams: not supported
>> 6 streams: not supported
>> 7 streams: not supported
>> 8 streams: not supported
>> VHT TX highest supported: 0 Mbps
>> Bitrates (non-HT):
>> * 6.0 Mbps
>> * 9.0 Mbps
>> * 12.0 Mbps
>> * 18.0 Mbps
>> * 24.0 Mbps
>> * 36.0 Mbps
>> * 48.0 Mbps
>> * 54.0 Mbps
>> Frequencies:
>> * 5180 MHz [36] (17.0 dBm)
>> * 5200 MHz [40] (17.0 dBm)
>> * 5220 MHz [44] (17.0 dBm)
>> * 5240 MHz [48] (17.0 dBm)
>> * 5260 MHz [52] (23.0 dBm) (no IR, radar detection)
>> DFS state: usable (for 1076 sec)
>> DFS CAC time: 60000 ms
>> * 5280 MHz [56] (23.0 dBm) (no IR, radar detection)
>> DFS state: usable (for 1076 sec)
>> DFS CAC time: 60000 ms
>> * 5300 MHz [60] (23.0 dBm) (no IR, radar detection)
>> DFS state: usable (for 1076 sec)
>> DFS CAC time: 60000 ms
>> * 5320 MHz [64] (23.0 dBm) (no IR, radar detection)
>> DFS state: usable (for 1076 sec)
>> DFS CAC time: 60000 ms
>> * 5500 MHz [100] (disabled)
>> * 5520 MHz [104] (disabled)
>> * 5540 MHz [108] (disabled)
>> * 5560 MHz [112] (disabled)
>> * 5580 MHz [116] (disabled)
>> * 5600 MHz [120] (disabled)
>> * 5620 MHz [124] (disabled)
>> * 5640 MHz [128] (disabled)
>> * 5660 MHz [132] (disabled)
>> * 5680 MHz [136] (disabled)
>> * 5700 MHz [140] (disabled)
>> * 5720 MHz [144] (disabled)
>> * 5745 MHz [149] (30.0 dBm)
>> * 5765 MHz [153] (30.0 dBm)
>> * 5785 MHz [157] (30.0 dBm)
>> * 5805 MHz [161] (30.0 dBm)
>> * 5825 MHz [165] (30.0 dBm)
>> Supported commands:
>> * new_interface
>> * set_interface
>> * new_key
>> * start_ap
>> * new_station
>> * set_bss
>> * authenticate
>> * associate
>> * deauthenticate
>> * disassociate
>> * join_ibss
>> * remain_on_channel
>> * set_tx_bitrate_mask
>> * frame
>> * frame_wait_cancel
>> * set_wiphy_netns
>> * set_channel
>> * set_wds_peer
>> * probe_client
>> * set_noack_map
>> * register_beacons
>> * start_p2p_device
>> * set_mcast_rate
>> * testmode
>> * channel_switch
>> * Unknown command (104)
>> * connect
>> * disconnect
>> Supported TX frame types:
>> * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90
>> 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>> * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90
>> 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>> * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0
>> 0xb0 0xc0 0xd0 0xe0 0xf0
>> * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90
>> 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>> * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80
>> 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>> * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80
>> 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>> * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90
>> 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>> * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80
>> 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>> Supported RX frame types:
>> * IBSS: 0x40 0xb0 0xc0 0xd0
>> * managed: 0x40 0xd0
>> * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
>> * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
>> * mesh point: 0xb0 0xc0 0xd0
>> * P2P-client: 0x40 0xd0
>> * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
>> * P2P-device: 0x40 0xd0
>> software interface modes (can always be added):
>> * AP/VLAN
>> * monitor
>> valid interface combinations:
>> * #{ managed, P2P-client } <= 8, #{ P2P-GO } <= 3, #{
>> P2P-device } <= 1, #{ AP } <= 7,
>> total <= 8, #channels <= 1, STA/AP BI must match
>> HT Capability overrides:
>> * MCS: ff ff ff ff ff ff ff ff ff ff
>> * maximum A-MSDU length
>> * supported channel width
>> * short GI for 40 MHz
>> * max A-MPDU length exponent
>> * min MPDU start spacing
>> Device supports TX status socket option.
>> Device supports HT-IBSS.
>> Device supports SAE with AUTHENTICATE command
>> Device supports scan flush.
>> Device supports per-vif TX power setting
>> Driver supports a userspace MPM
>> Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
>> Device supports static SMPS
>> =====================================================
>>
>> I am grateful for any help here and do have some time to help
>> debugging the issue.
>>
>> Marcel
>>
>> --
>>
>> ------------------------------------------------------
>> This message is not intended to have
>> contractual effect
>> ------------------------------------------------------
>>
>> _______________________________________________
>> ath10k mailing list
>> ath10k at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/ath10k
>
>
More information about the ath10k
mailing list