Report Firmware firmware-2.bin_10.1.467.2-1 Error

[Vu Hai NGUYEN]

Thank you for your response,
I didn't power down my cible to reboot, I just upload new program with new firmware and run it. The problem is when that error appear my console keep print it and I Have no longer access to my system, I can not type another command (dmesg) , then I have to reset my platform. I'll try to get the dmesg and sent you later.
My host platform is using processor Marvell Armada 370 and my module of wifi is Compex WLE900VX.
There's another problem: when I used the firmware version 999.999 some times when I ran my program and change the parameter of configuration, the firmware crash and I got a output dmesg which indicate a strange version of firmware (1.0.0.636 ???) : 

ath10k: firmware crashed!                                                       
ath10k: hardware name qca988x hw2.0 version 0x4100016c                          
ath10k: firmware version: 1.0.0.636 
ath10k: target register Dump Location: 0x00401930                               
ath10k: target Register Dump                                                    
ath10k: [00]: 0x4100016C 0x00000000 0x0098E3A9 0x00000000                       
ath10k: [04]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [08]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [12]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [16]: 0x00000000 0x00000000 0x00000000 0x0098E3A9                       
ath10k: [20]: 0x00000000 0x00401930 0x00000000 0x00000000                       
ath10k: [24]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [28]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [32]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [36]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [40]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [44]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [48]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [52]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [56]: 0x00000000 0x00000000 0x00000000 0x00000000    

and then It reload the firmware 999.999.  :

ath10k: firmware 999.999.0.636 booted

You can see the output of my dmesg 


NGUYEN Vu Hai
Acita-Sodielec
Route de Mayres - B.P. 9
12100 St GEORGES DE LUZENCON
FRANCE

________________________________________
De : Kalle Valo [kvalo at qca.qualcomm.com]
Date d'envoi : mardi 15 avril 2014 13:02
À : Vu Hai NGUYEN
Cc : ath10k at lists.infradead.org; Patrick CARNEIRO RODRIGUEZ
Objet : Re: Report Firmware  firmware-2.bin_10.1.467.2-1 Error

Vu Hai NGUYEN <vh.nguyen at actiasodielec.fr> writes:

> When I load the firmware-2.bin_10.1.467.2-1 I got this error when I
> put my device in mode ACCESS POINT: "PCI express error: irq - 228, Pex
> number: 0, Interrupt Cause Register value: 10" But if I use the
> version 999.999.0.x. I don't have this error.

I wonder if this has something to do with cold reset causing PCI bus
errors? But we need more information to say more. Can you send the full
dmesg output (from the beginning of kernel boot) along with detailed
descriptions of your host platform and what kind qca98xx board you have.

Even better is if you can also send a debug log output using debug mask
value 0x432. More info:

http://wireless.kernel.org/en/users/Drivers/ath10k/debug#Useful_debug_masks

--
Kalle Valo