[PATCH 1/2] ramips: mt7621: Add Arcadyan WE420223-99 support

Arınç ÜNAL arinc.unal at arinc9.com
Wed Dec 28 12:11:37 PST 2022


> The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access
> point distributed as Experia WiFi by KPN in the Netherlands. It features
> two ethernet ports and 2 internal antennas.
> 
> Specifications
> --------------
> SOC   : Mediatek MT7621AT
> ETH   : Two 1 gigabit ports, built into the SOC
> WIFI  : MT7615DN
> BUTTON: Reset
> BUTTON: WPS
> LED   : Power (green+red)
> LED   : WiFi (green+blue)
> LED   : WPS (green+red)
> LED   : Followme (green+red)
> Power : 12 VDC, 1A barrel plug
> 
> Winbond variant:
> RAM   : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM
> Flash : Winbond W25Q256JVFQ, 256Mb SPI
> U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1
> 
> Macronix variant:
> RAM   : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM
> Flash : MX25l25635FMI-10G, 256Mb SPI
> U-Boot: 1.1.3 (Dec  4 2017 - 11:37:57), Ralink 5.0.0.1
> 
> Serial
> ------
> The serial port needs a TTL/RS-232 3V3 level converter! The Serial
> setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin
> header.
> 
> The pinout is: VCC (the square), RX, TX, GND.
> 
> Installation
> ------------
> 1. Open the device, take off the heat sink
> 2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also
>    connect the RESET pin for stability (thanks @FPSUsername for reporting)
> 3. Make a backup in case you want to revert to stock later
> 4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash
> 5. Ensure the bootpartition variable is set to 0 in the U-Boot
>    environment located at 0x30000
> 
> Note that the U-Boot is password protected, this can optionally be
> removed. See the forum for more details [1]
> 
> MAC Addresses(stock)
> --------------------
> +----------+------------------+-------------------+
> | use      | address          | example           |
> +----------+------------------+-------------------+
> | Device   | label            | 00:00:00:11:00:00 |
> | Ethernet | + 3              | 00:00:00:11:00:03 |
> | 2g       | + 0x020000f00001 | 02:00:00:01:00:01 |
> | 5g       | + 1              | 00:00:00:11:00:01 |
> +----------+------------------+-------------------+
> 
> The label address is stored in ASCII in the board_data partition
> 
> Known issues
> ------------
> - 2g MAC address does not match stock due to missing support for that in
>   macaddr_add
> - Only the power LED is configured by default
> 
> References
> ----------
> [1] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653?u=harm
> 
> Signed-off-by: Harm Berntsen <git at harmberntsen.nl>
> ---
>  package/boot/uboot-envtools/files/ramips      |   3 +
>  .../dts/mt7621_arcadyan_we420223-99.dts       | 210 ++++++++++++++++++
>  target/linux/ramips/image/mt7621.mk           |  25 +++
>  .../mt7621/base-files/etc/board.d/02_network  |   8 +
>  .../etc/hotplug.d/ieee80211/10_fix_wifi_mac   |   9 +
>  .../mt7621/base-files/lib/upgrade/platform.sh |   1 +
>  6 files changed, 256 insertions(+)
>  create mode 100644 target/linux/ramips/dts/mt7621_arcadyan_we420223-99.dts
> 
> diff --git a/package/boot/uboot-envtools/files/ramips b/package/boot/uboot-envtools/files/ramips
> index f7f4821cef..8d4960e7a3 100644
> --- a/package/boot/uboot-envtools/files/ramips
> +++ b/package/boot/uboot-envtools/files/ramips
> @@ -17,6 +17,9 @@ alfa-network,awusfree1|\
>  alfa-network,quad-e4g|\
>  alfa-network,r36m-e4g|\
>  alfa-network,tube-e4g|\
> +arcadyan,we420223-99)
> +	ubootenv_add_uci_config "/dev/mtd2" "0x0" "0x1000" "0x1000"
> +	;;
>  engenius,esr600h|\
>  sitecom,wlr-4100-v1-002)
>  	ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x1000"
> diff --git a/target/linux/ramips/dts/mt7621_arcadyan_we420223-99.dts b/target/linux/ramips/dts/mt7621_arcadyan_we420223-99.dts
> new file mode 100644
> index 0000000000..f68d79af15
> --- /dev/null
> +++ b/target/linux/ramips/dts/mt7621_arcadyan_we420223-99.dts
> @@ -0,0 +1,210 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +
> +#include "mt7621.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +
> +/ {
> +	model = "Arcadyan WE420223-99";
> +	compatible = "arcadyan,we420223-99", "mediatek,mt7621-soc";
> +
> +	aliases {
> +		led-boot = &led_power_green;
> +		led-failsafe = &led_power_red;
> +		led-running = &led_power_green;
> +		led-upgrade = &led_wps_green;
> +		led-wifi = &led_wifi_green;
> +	};
> +
> +	chosen {
> +		bootargs = "console=ttyS0,57600 ubi.mtd=5 root=/dev/ubiblock0_0";
> +	};
> +
> +	keys {
> +		compatible = "gpio-keys";
> +
> +		reset {
> +			label = "reset";
> +			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_RESTART>;
> +		};
> +
> +		wps {
> +			label = "wps";
> +			gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_WPS_BUTTON>;
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		led_power_green: power_green {
> +			label = "green:power";
> +			gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
> +			color = <LED_COLOR_ID_GREEN>;
> +			function = LED_FUNCTION_POWER;
> +			default-state = "on";
> +		};
> +
> +		led_power_red: power_red {
> +			label = "red:power";
> +			gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
> +			color = <LED_COLOR_ID_RED>;
> +			function = LED_FUNCTION_FAULT;
> +		};
> +
> +		led_wifi_blue: wifi_blue {
> +			label = "blue:wifi";
> +			gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
> +			color = <LED_COLOR_ID_BLUE>;
> +			function = LED_FUNCTION_WLAN;
> +		};
> +
> +		led_wifi_green: wifi_green {
> +			label = "green:wifi";
> +			gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
> +			color = <LED_COLOR_ID_GREEN>;
> +			function = LED_FUNCTION_WLAN;
> +		};
> +
> +		led_wps_red: wps_red {
> +			label = "red:wps";
> +			gpios = <&gpio 45 GPIO_ACTIVE_LOW>;
> +			color = <LED_COLOR_ID_RED>;
> +			function = LED_FUNCTION_WPS;
> +		};
> +
> +		led_wps_green: wps_green {
> +			label = "green:wps";
> +			gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
> +			color = <LED_COLOR_ID_GREEN>;
> +			function = LED_FUNCTION_WPS;
> +		};
> +
> +		led_followme_r: followme_red {
> +			label = "red:followme";
> +			gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
> +			color = <LED_COLOR_ID_RED>;
> +		};
> +
> +		led_followme_g: followme_green {
> +			label = "green:followme";
> +			gpios = <&gpio 48 GPIO_ACTIVE_LOW>;
> +			color = <LED_COLOR_ID_GREEN>;
> +		};
> +	};
> +};
> +
> +&spi0 {
> +	status = "okay";
> +
> +	flash at 0 {
> +		compatible = "jedec,spi-nor";
> +
> +		reg = <0>;
> +		spi-max-frequency = <70000000>;
> +
> +		partitions {
> +			compatible = "fixed-partitions";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +
> +			partition at 0 {
> +				label = "ALL";
> +				reg = <0x0 0x2000000>;
> +				read-only;
> +			};
> +
> +			partition at 1 {
> +				label = "Bootloader";
> +				reg = <0x0 0x30000>;
> +				read-only;
> +			};
> +
> +			partition at 30000 {
> +				label = "Config";
> +				reg = <0x30000 0x10000>;
> +			};
> +
> +			factory: partition at 40000 {
> +				label = "Factory";
> +				reg = <0x40000 0x10000>;
> +				read-only;
> +			};
> +
> +			partition at 50000 {
> +				label = "kernel";
> +				reg = <0x50000 0x1f60000>;
> +			};
> +
> +			partition at 490000 {
> +				label = "rootfs";
> +				reg = <0x490000 0x1b20000>;
> +			};
> +
> +			partition at 1000000 {
> +				label = "Kernel2";
> +				reg = <0x1000000 0xfb0000>;
> +			};
> +
> +			partition at 1440000 {
> +				label = "RootFS2";
> +				reg = <0x1440000 0xb70000>;
> +			};
> +
> +			partition at 1fb0000 {
> +				label = "glbcfg";
> +				reg = <0x1fb0000 0x10000>;
> +				read-only;
> +			};
> +
> +			partition at 1fc0000 {
> +				label = "board_data";
> +				reg = <0x1fc0000 0x10000>;
> +				read-only;
> +			};
> +
> +			partition at 1fd0000 {
> +				label = "glbcfg2";
> +				reg = <0x1fd0000 0x10000>;
> +				read-only;
> +			};
> +
> +			partition at 1fe0000 {
> +				label = "board_data2";
> +				reg = <0x1fe0000 0x10000>;
> +				read-only;
> +			};
> +		};
> +	};
> +};
> +
> +&xhci {
> +	status = "disabled";
> +};
> +
> +&switch0 {
> +	ports {
> +		port at 0 {
> +			status = "okay";
> +		};
> +
> +		port at 1 {
> +			status = "okay";

Please define the label for the ports here.

Arınç



More information about the openwrt-devel mailing list