[PATCH] ath79: add support for Ubiquiti PowerBeam M (XW)
Adrian Schmutzler
mail at adrianschmutzler.de
Sun May 23 01:42:14 PDT 2021
Hi,
> -----Original Message-----
> From: openwrt-devel [mailto:openwrt-devel-bounces at lists.openwrt.org]
> On Behalf Of Russell Senior
> Sent: Sonntag, 23. Mai 2021 07:24
> To: openwrt-devel at lists.openwrt.org
> Cc: Russell Senior <russell at personaltelco.net>
> Subject: [PATCH] ath79: add support for Ubiquiti PowerBeam M (XW)
>
> This patch adds support for the Ubiquiti PowerBeam M (XW), e.g. PBE-M5-
> 400, a 802.11n wireless with a feed+dish form factor. This device was
> previously supported by the ar71xx loco-m-xw firmware.
this looks good in general. Somebody else should have a look at the network config, as this is the first non-wa ubnt device set up with rgmii-id.
Apart from that, please use "ubnt-powerbeam-m-xw" for the compatible. This is in line with the other xw devices, and actually it would have been better for the xm devices as well in the first place, so I don't count "There is no 'xm' powerbeam" as an argument :-)
Best
Adrian
>
> Specifications:
> - Atheros AR9342 SoC
> - 64 MB RAM
> - 8 MB SPI flash
> - 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in
> - Power and LAN green LEDs
> - 4x RSSI LEDs (red, orange, green, green)
> - UART (115200 8N1)
>
> Flashing via stock GUI:
> - WARNING: flashing OpenWrt from AirOS v5.6 or newer will brick your
> device! Read the wiki for more info.
> - Downgrade to AirOS v5.5.x (latest available is 5.5.10-u2) first.
> - Upload the factory image via AirOS web GUI.
>
> Flashing via TFTP:
> - WARNING: flashing OpenWrt from AirOS v5.6 or newer will brick your
> device! Read the wiki for more info.
> - Downgrade to AirOS v5.5.x (latest available is 5.5.10-u2) first.
> - Use a pointy tool (e.g., unbent paperclip) to keep the
> reset button pressed.
> - Power on the device (keep reset button pressed).
> - Keep pressing until LEDs flash alternatively LED1+LED3 =>
> LED2+LED4 => LED1+LED3, etc.
> - Release reset button.
> - The device starts a TFTP server at 192.168.1.20.
> - Set a static IP on the computer (e.g., 192.168.1.21/24).
> - Upload via tftp the factory image:
> $ tftp 192.168.1.20
> tftp> bin
> tftp> trace
> tftp> put openwrt-ath79-generic-xxxxx-ubnt_powerbeam-m-squashfs-
> factory.bin
>
> WARNING: so far, no non-destructive method has been discovered for
> opening the enclosure to reach the serial console. Internal photos are
> available here: https://fcc.io/SWX-NBM5HP
>
> Signed-off-by: Russell Senior <russell at personaltelco.net>
> ---
> .../ath79/dts/ar9342_ubnt_powerbeam-m.dts | 36
> +++++++++++++++++++
> .../generic/base-files/etc/board.d/01_leds | 1 +
> .../generic/base-files/etc/board.d/02_network | 1 +
> target/linux/ath79/image/generic-ubnt.mk | 8 +++++
> 4 files changed, 46 insertions(+)
> create mode 100644 target/linux/ath79/dts/ar9342_ubnt_powerbeam-
> m.dts
>
> diff --git a/target/linux/ath79/dts/ar9342_ubnt_powerbeam-m.dts
> b/target/linux/ath79/dts/ar9342_ubnt_powerbeam-m.dts
> new file mode 100644
> index 0000000000..1a2ce428f2
> --- /dev/null
> +++ b/target/linux/ath79/dts/ar9342_ubnt_powerbeam-m.dts
> @@ -0,0 +1,36 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +
> +#include "ar9342_ubnt_xw.dtsi"
> +
> +/ {
> + compatible = "ubnt,powerbeam-m", "ubnt,xw", "qca,ar9342";
> + model = "Ubiquiti PowerBeam M (XW)";
> +};
> +
> +&mdio0 {
> + status = "okay";
> +
> + phy-mask = <4>;
> +
> + phy4: ethernet-phy at 4 {
> + reg = <4>;
> + };
> +};
> +
> +ð0 {
> + status = "okay";
> +
> + /* default for ar934x, except for 1000M and 10M */
> + pll-data = <0x02000000 0x00000101 0x00001313>;
> +
> + mtd-mac-address = <&art 0x0>;
> +
> + phy-mode = "rgmii-id";
> + phy-handle = <&phy4>;
> +
> + gmac-config {
> + device = <&gmac>;
> + rxd-delay = <3>;
> + rxdv-delay = <3>;
> + };
> +};
> diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> index 1990353394..3bf120b92b 100644
> --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> @@ -383,6 +383,7 @@ ubnt,nanostation-loco-m-xw|\ ubnt,nanostation-
> m|\ ubnt,nanostation-m-xw|\ ubnt,picostation-m|\
> +ubnt,powerbeam-m|\
> ubnt,powerbridge-m|\
> ubnt,rocket-m)
> ucidef_set_rssimon "wlan0" "200000" "1"
> diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network
> b/target/linux/ath79/generic/base-files/etc/board.d/02_network
> index 4133b9d7d3..2b4ab946e1 100644
> --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
> +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
> @@ -85,6 +85,7 @@ ath79_setup_interfaces()
> ubnt,picostation-m|\
> ubnt,powerbeam-5ac-500|\
> ubnt,powerbeam-5ac-gen2|\
> + ubnt,powerbeam-m|\
> ubnt,powerbridge-m|\
> ubnt,rocket-m|\
> ubnt,unifiac-lite|\
> diff --git a/target/linux/ath79/image/generic-ubnt.mk
> b/target/linux/ath79/image/generic-ubnt.mk
> index 733d803d7a..5f403984be 100644
> --- a/target/linux/ath79/image/generic-ubnt.mk
> +++ b/target/linux/ath79/image/generic-ubnt.mk
> @@ -328,6 +328,14 @@ define Device/ubnt_powerbeam-5ac-gen2 endef
> TARGET_DEVICES += ubnt_powerbeam-5ac-gen2
>
> +define Device/ubnt_powerbeam-m
> + $(Device/ubnt-xw)
> + DEVICE_MODEL := PowerBeam M
> + DEVICE_PACKAGES += rssileds
> + SUPPORTED_DEVICES += loco-m-xw
> +endef
> +TARGET_DEVICES += ubnt_powerbeam-m
> +
> define Device/ubnt_powerbridge-m
> $(Device/ubnt-xm)
> SOC := ar7241
> --
> 2.31.1
>
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
-------------- next part --------------
A non-text attachment was scrubbed...
Name: openpgp-digital-signature.asc
Type: application/pgp-signature
Size: 834 bytes
Desc: not available
URL: <http://lists.openwrt.org/pipermail/openwrt-devel/attachments/20210523/574b2702/attachment.sig>
More information about the openwrt-devel
mailing list