Installing OpenWrt 21.02 on the TP-Link AD7200
Alex Henrie
alexhenrie24 at gmail.com
Sun May 2 08:56:04 BST 2021
On Sat, May 1, 2021 at 1:17 PM Alex Henrie <alexhenrie24 at gmail.com> wrote:
>
> On Fri, Apr 30, 2021 at 2:28 PM Sven Roederer <devel-sven at geroedel.de> wrote:
> >
> > not sure if you tried or if it even still applies to TPLink WebIf. But back in
> > the days there was a link in the length of the firmware filename to be
> > uploaded. The message was teh same "invalid firmware type".
> > Probably renaming the file is worth a try ...
>
> I tried renaming the file to
> AD7200v1-up-ver2-0-1-P1[20170103-rel71053]_2017-01-04_10.08.28.bin to
> match the latest stock firmware and the web interface still didn't
> accept it.
>
> I now have a header soldered to the four pins labeled JP4 but so far I
> have not been able to get serial communication. Do you happen to
> remember what the pinout is?
I got it working with help from a friend :-) The serial pinout on the
AD7200 is the same as on the C2600. I have attached the complete
serial output while attempting to upload OpenWrt over TFTP, but the
relevant part is:
Using eth1 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.1
Filename 'ArcherC2600_1.0_tp_recovery.bin'.
Load address: 0x42000000
Loading: *#################################################################
#################################################################
#################################################################
###########################################################o#####
################################################################
#################################################################
#################################################################
##########
done
Bytes transferred = 6818238 (6809be hex)
FirmwareRecovery: image downloaded
SF: Detected MX25U25635F with page size 4 KiB, total 32 MiB
FirmwareRecovery: image size :6809BE
FirmwareRecovery: fw-type:""
FirmwareRecovery: md5 checked ok
FirmwareRecovery: update partition got
FirmwareRecovery: this image do not match the hardware,now restart
FirmwareRecovery: recovery failed
}FirmwareRecovery: now restart
resetting ...
There might be a little corruption in the output because I used a
logic analyzer to decode it instead of a real UART.
What should I try next?
-Alex
-------------- next part --------------
FirmwareRecovery: Now doing recovery
FirmwareRecovery: trying to connect 192.168.0.66 ...
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Mac2 unit failed
Mac1 unit failed
Using eth1 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.1
Filename 'ArcherC2600_1.0_tp_recovery.bin'.
Load address: 0x42000000
Loading: *FirmwareRecovery: TFTP:try connect timeout
Using eth1 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.1
Filename 'ArcherC2600_1.0_tp_recovery.bin'.
Load address: 0x42000000
Loading: *FirmwareRecovery: TFTP:try connect timeout
Using eth1 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.1
Filename 'ArcherC2600_1.0_tp_recovery.bin'.
Load address: 0x42000000
Loading: *FirmwareRecovery: TFTP:try connect timeout
Using eth1 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.1
Filename 'ArcherC2600_1.0_tp_recovery.bin'.
Load address: 0x42000000
Loading: *FirmwareRecovery: TFTP:try connect timeout
Using eth1 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.1
Filename 'ArcherC2600_1.0_tp_recovery.bin'.
Load address: 0x42000000
Loading: *FirmwareRecovery: TFTP:try connect timeout
Using eth1 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.1
Filename 'ArcherC2600_1.0_tp_recovery.bin'.
Load address: 0x42000000
Loading: *FirmwareRecovery: TFTP:try connect timeout
Using eth1 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.1
Filename 'ArcherC2600_1.0_tp_recovery.bin'.
Load address: 0x42000000
Loading: *#################################################################
#################################################################
#################################################################
###########################################################o#####
################################################################
#################################################################
#################################################################
##########
done
Bytes transferred = 6818238 (6809be hex)
FirmwareRecovery: image downloaded
SF: Detected MX25U25635F with page size 4 KiB, total 32 MiB
FirmwareRecovery: image size :6809BE
FirmwareRecovery: fw-type:""
FirmwareRecovery: md5 checked ok
FirmwareRecovery: update partition got
FirmwareRecovery: this image do not match the hardware,now restart
FirmwareRecovery: recovery failed
}FirmwareRecovery: now restart
resetting ...
Resetting with watch dog!
U-Boot 2012.07 [Standard IPQ806X.LN,r8128] (May 25 2016 - 09:15:14)
smem ram ptable found: ver: 0 len: 5
DRAM: 491 MiB
PCI0 Link Intialized
PCI1 Link Intialized
PCI2 Link Intialized
SF: Detected MX25U25635F with page size 4 KiB, total 32 MiB
NAND: ipq_nand: unknown NAND device manufacturer: 0 device: 0
ipq_nand: failed to identify device
SF: Detected MX25U25635F with page size 4 KiB, total 32 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x2000000
32 MiB
MMC:
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: MAC1 addr:0:3:7f:ba:db:1
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init done
MAC2 addr:0:3:7f:ba:db:2
eth0, eth1
boot in 2 seconds
FirmwareRecovery: Now doing bootipq
MMC Device 0 not found
MMC Device 0 not found
Loading from nand1, offset 0x1f0000
Image Name: Linux-3.4.103
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1868608 Bytes = 1.8 MiB
Load Address: 41508000
Entry Point: 41508000
Automatic boot of image at addr 0x44000000 ...
Image Name: Linux-3.4.103
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1868608 Bytes = 1.8 MiB
Load Address: 41508000
Entry Point: 41508000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
info: "mtdparts" not set
Using machid 0x1260 from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Linux version 3.4.103 (tristan-xiao at tristanxiao-To-be-filled-by-O-E-M) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP PREEMPT Tue Mar 8 17:57:36 CST 2016
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] Machine: Qualcomm Atheros AP148 reference board
[ 0.000000] msm_reserve_memory: 0x44 00000, 0x600000
[ 0.000000] msm_reserve_memory: 0x44600000, 0x200000
[ 0.000000] memory pool 3 (start 5fc00000 size 400000) initialized
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] smem_find(137, 80): wrong size 72
[ 0.000000] socinfo_init: v6, id=202, ver=2.0, raw_Id=2064, raw_ver=2064, hw_plat=0, hw_plat_ver=65536
[ 0.000000] accessory_chip=0 hw_plat_subtype=0
[ 0.000000] PERCPU: Embedded 8 pages/cpu @c0c48000 s10240 r8192 d14336 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121642
[ 0.000000] Kernel command line: console=ttyHSL1,115200n8 root=mtd:rootfs rootfstype=squashfs
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 43MB 436MB = 479MB total
[ 0.000000] Memory: 477424k/489712k available, 13072k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf000000 - 0xff000000 ( 512 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdeb00000 ( 491 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0513000 (5164 kB)
[ 0.000000] .init : 0xc0600000 - 0xc0702800 (1034 kB)
[ 0.000000] .data : 0xc0704000 - 0xc07a0898 ( 627 kB)
[ 0.000000] .bss : 0xc07a08bc - 0xc0844ae0 ( 657 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:1689
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 31240ns, wraps every 134175798ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.150390] Calibrating delay using timer specific routine.. 12.55 BogoMIPS (lpj=62797)
[ 0.150421] pid_max: default: 32768 minimum: 301
[ 0.150890] Mount-cache hash table entries: 512
[ 0.152389] CPU: Testing write buffer coherency: ok
[ 0.152577] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.152608] Setting up static identity map for 0x4189b088 - 0x4189b110
[ 0.154889] CPU1: Booted secondary processor
[ 0.154951] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.155045] Brought up 2 CPUs
[ 0.155045] SMP: Total of 2 processors activated (25.11 BogoMIPS).
[ 0.171540] dummy:
[ 0.172227] NET: Registered protocol family 16
[ 0.172977] AXI: msm_bus_fabric_init_driver(): msm_bus_fabric_init_driver
[ 0.175164] meminfo_init: smem ram ptable found: ver: 0 len: 5
[ 0.175195] Found 1 memory banks grouped into 8 memory regions
[ 0.175195] TP-LINK Archer AD7200 v1
[ 0.175226] Force flash type to SPI!
[ 0.175507] gpiochip_add: registered GPIOs 0 to 151 on device: msmgpio
[ 0.176319] smem_find(137, 80): wrong size 72
[ 0.176351] socinfo_init: v6, id=202, ver=2.0, raw_id=2064, raw_ver=2064, hw_plat=0, hw_plat_ver=65536
[ 0.176351] accessory_chip=0 hw_plat_subtype=0
[ 0.176382] msm_rpm_init: RPM firmware 3.0.16777342
[ 0.184098] clk_tbl_nss - loaded
[ 0.211621] msm_dmov_memcpy_init: Success
[ 0.219025] sps:BAM 0x12244000 enabled: ver:0x5, number of pipes:20
[ 0.219056] sps:BAM 0x12244000 is registered.
[ 0.219275] sps:sps is ready.
[ 0.260824] msm_pcie_setup: link initialized
[ 0.261199] PCI host bridge to bus 0000:00
[ 0.261230] pci_bus 0000:00: bogt bus resource [mem 0x08000000-0x0fefffff]
[ 0.261730] PCI: bus0: Fast back to back transfers disabled
[ 0.261761] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.262480] PCI: bus1: Fast back to back transfers disabled
[ 0.300937] msm_pcie_setup: link initialized
[ 0.301280] PCI host bridge to bus 0000:02
[ 0.301280] pci_bus 0000:02: root bus resource [mem 0x2e000000-0x31efffff]
[ 0.301780] PCI: bus2: Fast back to back transfers disabled
[ 0.301780] pci 0000:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.302592] PCI: bus3: Fast back to back transfers disabled
[ 0.341049] msm_pcie_setup: link initialized
[ 0.341393] PCI host bridge to bus 0000:04
[ 0.341393] pci_bus 0000:04: root bus resource [mem 0x32000000-0x35efffff]
[ 0.341861] PCI: bus4: Fast back to back transfers disabled
[ 0.341861] pci 0000:04:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.342580] PCI: bus5: Fast back to back transfers disabled
[ 0.343548] pci 0000:04:00.0: BAR 8: assigned [mem 0x32000000-0x321fffff]
[ 0.343580] pci 0000:05:00.0: BAR 0: assigned [mem 0x32000000-0x321fffff 64bit]
[ 0.343611] pci 0000:04:00.0: PCI bridge to [bus 05-05]
[ 0.343642] pci 0000:04:00.0: bridge window [mem 0x32000000-0x321fffff]
[ 0.343705] PCI: enabling device 0000:04:00.0 (0140 -> 0143)
[ 0.343767] pci 0000:02:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.343767] pci 0000:03:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.343830] pci 0000:02:00.0: PCI bridge to [bus 03-03]
[ 0.343830] pci 0000:02:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.343892] PCI: enabling device 0000:02:00.0 (0140 -> 0143)
[ 0.343955] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[ 0.343986] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.344017] pci 0000:00:00.0: PCI bridge to [bus 01-01]
[ 0.344048] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.344079] PCI: enabling device 0000:00:00.0 (0140 -> 0143)
[ 0.364636] bio: create slab <bio-0> at 0
[ 0.366198] SCSI subsystem initialized
[ 0.368041] spi_qsd spi_qsd.5: master is unqueued, this is deprecated
[ 0.370446] spi_qsd spi_qsd.6: master is unqueued, this is deprecated
[ 0.374445] Switching to clocksource gp_timer
[ 0.395345] NET: Registered protocol family 2
[ 0.405092] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.405560] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.405779] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.405966] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.405966] TCP: reno registered
[ 0.405998] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.405998] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.406466] NET: Registered protocol family 1
[ 0.408278] smd: register irq failed on wcnss_a11
[ 0.408278] smd: deregistering IRQs
[ 0.408341] SMD: smd_core_platform_init() failed
[ 0.409090] Partition(from smem) ART -- Offset:1b0000 Size:40000
[ 0.409090] Partition(from smem) rootfs -- Offset:3f0000 Size:1b00000
[ 0.409122] get_bootconfig_partition: magic not found
[ 0.424117] acpuclk-ipq806x acpuclk-ipq806x: SPEED BIN: 0
[ 0.424117] acpuclk-ipq806x acpuclk-ipq806x: ACPU PVS: 1
[ 0.430834] acpuclk-ipq806x acpuclk-ipq806x: CPU0: 6 frequencies supported
[ 0.430865] acpuclk-ipq806x acpuclk-ipq806x: CPU1: 6 frequencies supported
[ 0.432396] msm_rpm_log_probe: OK
[ 0.452546] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.452546] jffs2: version 2.2. (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) 2001-2006 Red Hat, Inc.
[ 0.453889] msgmni has been set to 932
[ 0.455076] io scheduler noop registered
[ 0.455107] io scheduler deadline registered (default)
[ 0.456451] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.459075] msm_serial_hs.0: ttyHS0 at MMIO 0x12490000 (irq = 227) is a MSM HS UART
[ 0.459637] msm_serial_hs module loaded
[ 0.459825] msm_serial_hsl: detected port #1
[ 0.459950] msm_serial_hsl.1: ttyHSL1 at MMIO 0x16340000 (irq = 184) is a MSM
[ 0.460356] msm_serial_hsl: console setup on port #1
[ 1.213714] console [ttyHSL1] enabled
[ 1.217869] msm_serial_hsl: driver initialized
[ 1.227085] ahci ahci.0: forcing PORTS_IMPL to 0x1
[ 1.230896] ahci ahci.0: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 1.238800] ahci ahci.0: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 1.247860] scsi0 : ahci_platform
[ 1.250859] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 241
[ 1.261105] m25p80 spi5.0: found mx25u25635f, expected s25fl512s
[ 1.266135] m25p80 spi5.0: mx25u25635f (32768 Kbytes)
[ 1.271665] Creating 2 MTD partitions on "m25p80":
[ 1.276038] 0x0000001b0000-0x0000001f0000 : "ART"
[ 1.282411] 0x0000003f0000-0x000001ef0000 : "rootfs"
[ 1.288034] mtd: partition "rootfs" set to be root filesystem
[ 1.292970] flash_chrdev : flash_chrdev_init
[ 1.325741] GPIO Bitbanged MDIO: probed
[ 1.333676] cpuidle: using governor ladder
[ 1.336769] cpuidle: using governor menu
[ 1.341674] TCP: cubic registered
[ 1.343955] NET: Registered protocol family 17
[ 1.348641] Bridge firewalling registered
[ 1.352389] 8021q: 802.1Q VLAN Support v1.8
[ 1.356701] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 1.364292] Registering SWP/SWPB emulation handler
[ 1.369103] clock_late_init: Removing enables held for handed-off clocks
[ 1.384348] ipq_nss_get_mac_addr: MAC[0]: ff:ff:ff:ff:ff:ff
[ 1.389034] ipq_nss_get_mac_addr: MAC[1]: ff:ff:ff:ff:ff:ff
[ 1.394564] ipq_nss_get_mac_addr: MAC[2]: ff:ff:ff:ff:ff:ff
[ 1.400124] ipq_nss_get_mac_addr: MAC[3]: ff:ff:ff:ff:ff:ff
[ 1.405779] no pmic restart interrupt specified
[ 1.604498] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.620930] VFS: Mounted root (squashfs filesystem) readonly on device 31:1.
[ 1.627553] Freeing init memory: 1032K
[ 4.355045] tfat: module license 'Commercial. For support email exfat-support at tuxera.com' taints kernel.
[ 4.363480] Disabling lock debugging due to kernel taint
[ 4.369946] Tuxera FAT 12/16/32 driver version 3014.9.10 [Flags: R/W MODULE].
[ 4.502780] Tuxera exFAT driver version 3014.9.10 [Flags: R/W MODULE].
[ 4.768416] Tuxera NTFS driver 3015.1.29 [Flags: R/W MODULE].
[ 4.795376] Tuxera HFS+ driver 3014.7.28- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -
Please press Enter to activate this console. ssdk_plat_init start
[ 7.526023] Register QCA PHY driver
[ 7.708809] qca-ssdk module init succeeded!
[ 7.915807] NET: Registered protocol family 10
[ 8.119868] Loading modules backported from Linux version v3.2-rc1-243797-g2dd6906
[ 8.126429] Backport generated by backports.git backports-20150424-2-g9828be0
[ 8.293751] cfg80211: Calling CRDA to update world regulatory domain
[ 8.299500] cfg80211: World regulatory domain updated:
[ 8.304186] cfg80211: DFS Master region: unset
[ 8.308591] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 8.318431] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 300 mBm), (N/A)
[ 8.326179] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 300 mBm), (N/A)
[ 8.334895] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 300 mBm), (N/A)
[ 8.341955] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 300 mBm), (N/A)
[ 8.350671] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 300 mBm), (N/A)
[ 8.357763] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 8.506747] usbcore: registered new interface driver usbfs
[ 8.511246] usbcore: registered new interface driver hub
[ 8.516619] usbcore: registered new device driver usb
[ 8.742674] md: linear personality registered for level -1
[ 8.872383] md: raid0 personality registered for level 0
[ 8.885035] md: raid1 personality registered for level 1
[ 9.076038] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 9.160168] PPP generic driver version 2.4.2
[ 9.283661] tun: Universal TUN/TAP device driver, 1.6
[ 9.287691] tun: (C) 1999-2004 Max Krasnyansky <maxk at qualcomm.com>
[ 9.340487] PPP MPPE Compression module registered
[ 9.372571] **********************************************************
[ 9.378006] * Driver :NSS GMAC Driver for RTL v(3.72a)
[ 9.383286] * Version :1.0
[ 9.386160] * Copyright :Copyright (c) 2013-2014 The Linux Foundation. All rights reserved.
[ 9.394501] **********************************************************
[ 9.401468] GMAC1(dd751480) Invalid MAC@ - using de:df:e0:e1:e2:e3
[ 11.922899] GMAC2(dd752c80) Invalid MAC@ - using 16:17:18:19:1a:1b
[ 11.989065] L2TP core driver, V2.0
[ 11.999718] L2TP netlink interface
[ 12.274383] nss_driver - fw of size 354304 bytes copied to load addr: 40000000, nss_id : 0
[ 12.301593] nss_driver - Turbo Support 1
[ 12.305748] bf3fb3dd: NSS Shaping is enabled, handler id: 0
[ 12.450640] nss_driver - fw of size 5392 bytes copied to load addr: 40800000, nss_id : 1
[ 12.458856] Error - Duplicate Interface CB Registered for interface 75
[ 12.464354] Error - Duplicate Interface CB Registered for interface 78
[ 12.508028] IPv6 over IPv4 tunneling driver
[ 12.548953] nss_macsec init success
[ 12.676194] wil6210 0000:05:00.0: wil6210 device found [1ae9:0310] (rev 2)
[ 12.682068] PCI: enabling device 0000:05:00.0 (0140 -> 0142)
[ 12.687785] wil6210 0000:05:00.0: CSR at [mem 0x32000000-0x321fffff 64bit] -> 0xe0000000
[ 12.696282] wil6210 0000:05:00.0: (unregistered net_device): Board hardware is Sparrow B0
[ 12.704248] wil6210 0000:05:00.0: (unregistered net_device): _wil6210_disconnect(bssid= (null), reason=3, ev-)
[ 12.774570] wil6210 0000:05:00.0: (unregistered net_device): Boot Loader struct v2: MAC = 04:ce:14:0a:56:04 RF = 0x0000 (status 0x0000) bband = 0x00000000
[ 12.787378] wil6210 0000:05:00.0: (unregistered net_device): Boot Loader build 255.255.0.6836
[ 12.795876] wil6210 0000:05:00.0: (unregistered net_device): Registered with NSS
[ 12.831958] gre: GRE over IPv4 demultiplexor driver
[ 12.865729] ip_gre: GRE over IPv4 tunneling driver
[ 12.891471] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 13.106404] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.205529] NET: Registered protocol family 24
[ 13.339737] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 13.345360] msm_hsusb_host msm_hsusb_host: unable to find transceiver
[ 13.489721] nf_conntrack version 0.5.0 (7475 buckets, 29900 max)
[ 13.631208] PPPoL2TP kernel driver, V2.0
[ 13.659044] PPTP driver version 0.8.5
[ 13.988409] xt_time: kernel timezone is -0000
[ 14.323273] nf_conntrack_rtsp v0.6.21 loading
[ 14.335020] nf_nat_rtsp v0.6.21 loading
[ 14.376351] Netfilter messages via NETLINK v0.30.
[ 14.406091] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.518681] ctnetlink v0.93: registering with nfnetlink.
[ 14.608247
ipq-dwc3 ipq-dwc3.0: unable to read platform data num of dbm eps
[ 14.715307] xhci-hcd xhci-hcd.0: xHCI Host Controller
[ 14.719368] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1
[ 14.726647] xhci-hcd xhci-hcd.0: irq 142, io mem 0x11000000
[ 14.732739] hub 1-0:1.0: USB hub found
[ 14.735832] hub 1-0:1.0: 1 port detected
[ 14.739862] xhci-hcd xhci-hcd.0: xHCI Host Controller
[ 14.744767] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2
[ 14.752483] hub 2-0:1.0: USB hub found
[ 14.755701] hub 2-0:1.0: 1 port detected
[ 14.761324] ipq-dwc3 ipq-dwc3.1: unable to read platform data num of dbm eps
[ 14.867978] xhci-hcd xhci-hcd.1: xHCI Host Controller
[ 14.872008] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 3
[ 14.879287] xhci-hcd xhci-hcd.1: irq 237, io mem 0x10000000
[ 14.885410] hub 3-0:1.0: USB hub found
[ 14.888472] hub 3-0:1.0: 1 port detected
[ 14.892533] xhci-hcd xhci-hcd.1: xHCI Host Controller
[ 14.897438] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 4
[ 14.905185] hub 4-0:1.0: USB hub found
[ 14.908341] hub 4-0:1.0: 1 port detected
[ 15.204592] ECM init
[ 15.208184] ECM init complete
[ 15.238144] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 15.306685] Initializing USB Mass Storage driver...
[ 15.310715] usbcore: registered new interface driver usb-storage
[ 15.316526] USB Mass Storage support registered.
[ 15.331021] fuse init (API version 7.18)
-------------------- Load config start --------------------
reloadconfig() begin:
reloadconfig() end:
-------------------- Load config end ----------------------
-------------------- Load profile start -------------------
reload_profile() begin:
reload_profile() end:
-------------------- Load profile end ---------------------
-------------------- Load QoS DB start --------------------
-------------------- Load QoS DB end ----------------------
bad magic number
GMT+08:00
[ 23.722555] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 26.515901] device eth1 entered promiscuous mode
[ 26.520056] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 26.527710] br-lan: port 1(eth1) entered forwarding state
[ 26.532083] br-lan: port 1(eth1) entered forwarding state
[ 26.540612] ADDRCONF(NETDEV_UP): eth0: link is not ready
usbshare boot start
More information about the openwrt-devel
mailing list