[OpenWrt-Devel] [PATCH] ath79: add support for COMFAST CF-E130N v2

Roger Pueyo Centelles | Guifi.net roger.pueyo at guifi.net
Mon Nov 11 16:21:56 EST 2019


Hi,

In addition to Adrian's comments, could it be that the device was a
802.11bgn router?
www.comfast.com.cn/index.php?m=content&c=index&a=show&catid=19&id=23

Cheers,

Roger

El 11/11/19 a les 10:09, Adrian Schmutzler ha escrit:
> Hi,
>
>> +	aliases {
>> +		serial0 = &uart;
>> +		led-boot = &lan;
>> +		led-failsafe = &lan;
>> +		led-upgrade = &lan;
> Please don't use LAN here, as it will be ambiguous.
> For TP-Link CPE devices, we relied on rssi_high for this task, so either use this one or choose "unused".
> Please prefix the led label (but not the node name) with "led_", so either led_rssihigh or led_unused ...
>
>> +		label-mac-device = &eth0;
>> +	};
>> +
>> +	leds {
>> +		compatible = "gpio-leds";
>> +
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&led_rssimediumhigh_pin>;
>> +
>> +		wlan {
>> +			label = "cf-e130n-v2:green:wlan";
>> +			gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
>> +			linux,default-trigger = "phy0tpt";
>> +		};
>> +
>> +		lan: lan {
>> +			label = "cf-e130n-v2:green:lan";
>> +			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
>> +		};
>> +
>> +		unused {
>> +			label = "cf-e130n-v2:green:unused";
>> +			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
>> +		};
>> +
>> +		rssilow {
>> +			label = "cf-e130n-v2:red:rssilow";
>> +			gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
>> +		};
>> +
>> +		rssimediumlow {
>> +			label = "cf-e130n-v2:red:rssimediumlow";
>> +			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
>> +		};
>> +
>> +		rssimediumhigh {
>> +			label = "cf-e130n-v2:green:rssimediumhigh";
>> +                        // No individual GPIOs matched this LED!
>> +		};
>> +
>> +		rssihigh {
>> +			label = "cf-e130n-v2:green:rssihigh";
>> +			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
>> +		};
>> +	};
>> +
>> +	keys {
>> +		compatible = "gpio-keys";
>> +
>> +		reset {
>> +			label = "reset";
>> +			linux,code = <KEY_RESTART>;
>> +			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
>> +			debounce-interval = <60>;
>> +		};
>> +	};
>> +};
>> +
>> +&pinmux {
>> +		led_rssimediumhigh_pin: pinmux_rssimediumhigh_pin {
>> +			pinctrl-single,bits = <0x10 0x0 0xff>;
>> +		};
> Single tab indent.
>
>> +};
>> +
>> +&spi {
>> +	status = "okay";
>> +	num-cs = <1>;
> Add empty line after status.
>
>> +
>> +	flash at 0 {
>> +		compatible = "jedec,spi-nor";
>> +		reg = <0>;
>> +		spi-max-frequency = <25000000>;
>> +
>> +		partitions {
>> +			compatible = "fixed-partitions";
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +
>> +			uboot:	partition at 0 {
>> +				label = "u-boot";
>> +				reg = <0x000000 0x010000>;
>> +				read-only;
>> +			};
>> +
>> +			art: partition at 10000 {
>> +				label = "art";
>> +				reg = <0x010000 0x010000>;
>> +				read-only;
>> +			};
>> +
>> +			firmware: partition at 20000 {
>> +				compatible = "denx,uimage";
>> +				label = "firmware";
>> +				reg = <0x020000 0x7d0000>;
>> +			};
>> +
>> +			nvram: partition at 7f0000 {
>> +				label = "nvram";
>> +				reg = <0x7f0000 0x010000>;
>> +				read-only;
>> +			};
> We typically only add node labels when they are required, so here we would only need "art:". Keep the label properties, though ...
>
>> +		};
>> +	};
>> +};
>> +
>> +&uart {
>> +	status = "okay";
>> +};
>> +
>> +&eth0 {
>> +	status = "okay";
>> +	phy-handle = <&swphy0>;
>> +	mtd-mac-address = <&art 0x0>;
> Add empty lines after status and after phy-handle.
>
>> +
>> +	gmac-config {
>> +		device = <&gmac>;
>> +		switch-phy-swap = <1>;
>> +	};
>> +};
>> +
>> +&wmac {
>> +	status = "okay";
> Add empty line after status.
>
>> +	mtd-cal-data = <&art 0x1000>;
>> +};
>> +
>> diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
>> b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
>> index fbb0d0ea03..3046d34605 100755
>> --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
>> +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
>> @@ -47,6 +47,14 @@ comfast,cf-e120a-v3)
>>  	ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH"
>> "$boardname:green:rssimediumhigh" "wlan0" "51" "100"
>>  	ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "$boardname:green:rssihigh"
>> "wlan0" "76" "100"
>>  	;;
>> +comfast,cf-e130n-v2)
>> +	ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0"
>> +	ucidef_set_rssimon "wlan0" "200000" "1"
>> +	ucidef_set_led_rssi "rssilow" "RSSILOW" "$boardname:red:rssilow"
>> "wlan0" "1" "100"
>> +	ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW"
>> "$boardname:red:rssimediumlow" "wlan0" "26" "100"
>> +	ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH"
>> "$boardname:green:rssimediumhigh" "wlan0" "51" "100"
> Will this work without a defined gpio?
>
>> +	ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "$boardname:green:rssihigh"
>> "wlan0" "76" "100"
>> +	;;
>>  comfast,cf-e313ac)
>>  	ucidef_set_led_switch "lan" "LAN" "$boardname:green:lan" "switch0"
>> "0x02"
>>  	ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth1"
>> diff --git a/target/linux/ath79/image/generic.mk
>> b/target/linux/ath79/image/generic.mk
>> index 70631c20d0..48d6864ecb 100644
>> --- a/target/linux/ath79/image/generic.mk
>> +++ b/target/linux/ath79/image/generic.mk
>> @@ -258,6 +258,16 @@ define Device/comfast_cf-e120a-v3
>>  endef
>>  TARGET_DEVICES += comfast_cf-e120a-v3
>>
>> +define Device/comfast_cf-e130n-v2
>> +  ATH_SOC := qca9531
>> +  DEVICE_VENDOR := COMFAST
>> +  DEVICE_MODEL := CF-E130N
>> +  DEVICE_VARIANT := v2
>> +  DEVICE_PACKAGES := rssileds kmod-leds-gpio -swconfig -uboot-envtools
>> +  IMAGE_SIZE := 16192k
> That's wrong. You have 0x7d0000, not 0xfd0000 ...
>
> Best
>
> Adrian 
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20191111/d8edd252/attachment.htm>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20191111/d8edd252/attachment.sig>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel


More information about the openwrt-devel mailing list