[OpenWrt-Devel] [PATCH] ath79: add support for TP-Link Archer C7 v1
Christian Lamparter
chunkeey at gmail.com
Fri Aug 17 12:36:32 EDT 2018
TP-Link Archer C7 v1 is a dual band router
based on Qualcomm/Atheros QCA9558 + QCA9880.
Specification:
- 720 MHz CPU
- 128 MB of RAM (Various chips)
- 8 MB of FLASH (Various chips)
- SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi
- minipcie slot with 3T3R 5 GHz QCA9880-AR1A (unsupported by ath10k!)
- 5x 10/100/1000 Mbps Ethernet (AR8327N Switch)
- 10x LEDs, 2x software buttons
For further informwation on the device, visit the wiki:
<https://openwrt.org/toh/tp-link/archer-c7-1750>
Signed-off-by: Christian Lamparter <chunkeey at gmail.com>
---
.../ath79/base-files/etc/board.d/02_network | 1 +
.../ath79/dts/qca9558_tplink_archer-c7-v1.dts | 46 +++++++++++++++++++
target/linux/ath79/image/generic-tp-link.mk | 9 ++++
3 files changed, 56 insertions(+)
create mode 100644 target/linux/ath79/dts/qca9558_tplink_archer-c7-v1.dts
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index 9e31be40f9..0d33549890 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -81,6 +81,7 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0 at eth0" "3:lan:1" "5:lan:2" "4:wan"
;;
+ tplink,archer-c7-v1|\
tplink,archer-c7-v2|\
tplink,tl-wdr4900-v2)
ucidef_add_switch "switch0" \
diff --git a/target/linux/ath79/dts/qca9558_tplink_archer-c7-v1.dts b/target/linux/ath79/dts/qca9558_tplink_archer-c7-v1.dts
new file mode 100644
index 0000000000..3d7713f675
--- /dev/null
+++ b/target/linux/ath79/dts/qca9558_tplink_archer-c7-v1.dts
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca9558_tplink_archer-c7.dtsi"
+
+/ {
+ compatible = "tplink,archer-c7-v1", "qca,qca9558";
+ model = "TP-Link Archer C7 Version 1";
+};
+
+&gpio_keys {
+ rfkill {
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ linux,input-type = <EV_SW>;
+ debounce-interval = <60>;
+ };
+};
+
+&gpio_leds {
+ wlan5g {
+ label = "tp-link:green:wlan5g";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ linux,default-trigger = "phy0tpt";
+ };
+};
+
+&mtdparts {
+ uboot: u-boot at 0 {
+ reg = <0x000000 0x020000>;
+ read-only;
+ };
+
+ firmware at 20000 {
+ reg = <0x020000 0x7d0000>;
+ };
+
+ art: art at ff0000 {
+ reg = <0x7f0000 0x010000>;
+ read-only;
+ };
+};
diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk
index 4c85099a1a..926c3cb618 100644
--- a/target/linux/ath79/image/generic-tp-link.mk
+++ b/target/linux/ath79/image/generic-tp-link.mk
@@ -1,5 +1,14 @@
include ./common-tp-link.mk
+define Device/tplink_archer-c7-v1
+ $(Device/tplink-8mlzma)
+ ATH_SOC := qca9558
+ DEVICE_TITLE := TP-LINK Archer C7 v1
+ DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport kmod-ath10k ath10k-firmware-qca988x
+ TPLINK_HWID := 0x75000001
+endef
+TARGET_DEVICES += tplink_archer-c7-v1
+
define Device/tplink_archer-c7-v2
$(Device/tplink-16mlzma)
ATH_SOC := qca9558
--
2.18.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list