[OpenWrt-Devel] [PATCH] generic: revert workarounds for AR8337 switch
Mathias Kresin
dev at kresin.me
Thu Aug 16 15:44:36 EDT 2018
The intention of 967b6be118e3 ("ar8327: Add workarounds for AR8337
switch") was to remove the register fixups for AR8337. But instead they
were removed for AR8327.
The RGMII RX delay is forced even if the port is used as phy instead of
mac, which results in no package flow at least for one board.
Fixes: FS#1664
Signed-off-by: Mathias Kresin <dev at kresin.me>
---
.../linux/generic/files/drivers/net/phy/ar8327.c | 42 +---------------------
.../linux/generic/files/drivers/net/phy/ar8327.h | 21 -----------
2 files changed, 1 insertion(+), 62 deletions(-)
diff --git a/target/linux/generic/files/drivers/net/phy/ar8327.c b/target/linux/generic/files/drivers/net/phy/ar8327.c
index 7bfc187..74f0a08 100644
--- a/target/linux/generic/files/drivers/net/phy/ar8327.c
+++ b/target/linux/generic/files/drivers/net/phy/ar8327.c
@@ -506,14 +506,6 @@ ar8327_hw_config_pdata(struct ar8xxx_priv *priv,
ar8xxx_write(priv, AR8327_REG_PAD0_MODE, t);
t = ar8327_get_pad_cfg(pdata->pad5_cfg);
- if (chip_is_ar8337(priv)) {
- /*
- * Workaround: RGMII RX delay setting needs to be
- * always specified for AR8337 to avoid port 5
- * RX hang on high traffic / flood conditions
- */
- t |= AR8327_PAD_RGMII_RXCLK_DELAY_EN;
- }
ar8xxx_write(priv, AR8327_REG_PAD5_MODE, t);
t = ar8327_get_pad_cfg(pdata->pad6_cfg);
ar8xxx_write(priv, AR8327_REG_PAD6_MODE, t);
@@ -678,39 +670,6 @@ ar8327_init_globals(struct ar8xxx_priv *priv)
/* Disable EEE on all phy's due to stability issues */
for (i = 0; i < AR8XXX_NUM_PHYS; i++)
data->eee[i] = false;
-
- if (chip_is_ar8337(priv)) {
- /* Update HOL registers with values suggested by QCA switch team */
- for (i = 0; i < AR8327_NUM_PORTS; i++) {
- if (i == AR8216_PORT_CPU || i == 5 || i == 6) {
- t = 0x3 << AR8327_PORT_HOL_CTRL0_EG_PRI0_BUF_S;
- t |= 0x4 << AR8327_PORT_HOL_CTRL0_EG_PRI1_BUF_S;
- t |= 0x4 << AR8327_PORT_HOL_CTRL0_EG_PRI2_BUF_S;
- t |= 0x4 << AR8327_PORT_HOL_CTRL0_EG_PRI3_BUF_S;
- t |= 0x6 << AR8327_PORT_HOL_CTRL0_EG_PRI4_BUF_S;
- t |= 0x8 << AR8327_PORT_HOL_CTRL0_EG_PRI5_BUF_S;
- t |= 0x1e << AR8327_PORT_HOL_CTRL0_EG_PORT_BUF_S;
- } else {
- t = 0x3 << AR8327_PORT_HOL_CTRL0_EG_PRI0_BUF_S;
- t |= 0x4 << AR8327_PORT_HOL_CTRL0_EG_PRI1_BUF_S;
- t |= 0x6 << AR8327_PORT_HOL_CTRL0_EG_PRI2_BUF_S;
- t |= 0x8 << AR8327_PORT_HOL_CTRL0_EG_PRI3_BUF_S;
- t |= 0x19 << AR8327_PORT_HOL_CTRL0_EG_PORT_BUF_S;
- }
- ar8xxx_write(priv, AR8327_REG_PORT_HOL_CTRL0(i), t);
-
- t = 0x6 << AR8327_PORT_HOL_CTRL1_ING_BUF_S;
- t |= AR8327_PORT_HOL_CTRL1_EG_PRI_BUF_EN;
- t |= AR8327_PORT_HOL_CTRL1_EG_PORT_BUF_EN;
- t |= AR8327_PORT_HOL_CTRL1_WRED_EN;
- ar8xxx_rmw(priv, AR8327_REG_PORT_HOL_CTRL1(i),
- AR8327_PORT_HOL_CTRL1_ING_BUF |
- AR8327_PORT_HOL_CTRL1_EG_PRI_BUF_EN |
- AR8327_PORT_HOL_CTRL1_EG_PORT_BUF_EN |
- AR8327_PORT_HOL_CTRL1_WRED_EN,
- t);
- }
- }
}
static void
@@ -1498,6 +1457,7 @@ const struct ar8xxx_chip ar8327_chip = {
.atu_flush_port = ar8327_atu_flush_port,
.vtu_flush = ar8327_vtu_flush,
.vtu_load_vlan = ar8327_vtu_load_vlan,
+ .phy_fixup = ar8327_phy_fixup,
.set_mirror_regs = ar8327_set_mirror_regs,
.get_arl_entry = ar8327_get_arl_entry,
.sw_hw_apply = ar8327_sw_hw_apply,
diff --git a/target/linux/generic/files/drivers/net/phy/ar8327.h b/target/linux/generic/files/drivers/net/phy/ar8327.h
index 2309e52..d53ef88 100644
--- a/target/linux/generic/files/drivers/net/phy/ar8327.h
+++ b/target/linux/generic/files/drivers/net/phy/ar8327.h
@@ -278,28 +278,7 @@
#define AR8327_REG_PORT_PRIO(_i) (0x664 + (_i) * 0xc)
-#define AR8327_REG_PORT_HOL_CTRL0(_i) (0x970 + (_i) * 0x8)
-#define AR8327_PORT_HOL_CTRL0_EG_PRI0_BUF BITS(0, 4)
-#define AR8327_PORT_HOL_CTRL0_EG_PRI0_BUF_S 0
-#define AR8327_PORT_HOL_CTRL0_EG_PRI1_BUF BITS(4, 4)
-#define AR8327_PORT_HOL_CTRL0_EG_PRI1_BUF_S 4
-#define AR8327_PORT_HOL_CTRL0_EG_PRI2_BUF BITS(8, 4)
-#define AR8327_PORT_HOL_CTRL0_EG_PRI2_BUF_S 8
-#define AR8327_PORT_HOL_CTRL0_EG_PRI3_BUF BITS(12, 4)
-#define AR8327_PORT_HOL_CTRL0_EG_PRI3_BUF_S 12
-#define AR8327_PORT_HOL_CTRL0_EG_PRI4_BUF BITS(16, 4)
-#define AR8327_PORT_HOL_CTRL0_EG_PRI4_BUF_S 16
-#define AR8327_PORT_HOL_CTRL0_EG_PRI5_BUF BITS(20, 4)
-#define AR8327_PORT_HOL_CTRL0_EG_PRI5_BUF_S 20
-#define AR8327_PORT_HOL_CTRL0_EG_PORT_BUF BITS(24, 6)
-#define AR8327_PORT_HOL_CTRL0_EG_PORT_BUF_S 24
-
#define AR8327_REG_PORT_HOL_CTRL1(_i) (0x974 + (_i) * 0x8)
-#define AR8327_PORT_HOL_CTRL1_ING_BUF BITS(0, 4)
-#define AR8327_PORT_HOL_CTRL1_ING_BUF_S 0
-#define AR8327_PORT_HOL_CTRL1_EG_PRI_BUF_EN BIT(6)
-#define AR8327_PORT_HOL_CTRL1_EG_PORT_BUF_EN BIT(7)
-#define AR8327_PORT_HOL_CTRL1_WRED_EN BIT(8)
#define AR8327_PORT_HOL_CTRL1_EG_MIRROR_EN BIT(16)
#define AR8337_PAD_MAC06_EXCHANGE_EN BIT(31)
--
2.7.4
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list