[OpenWrt-Devel] [PATCH] net: dsa: rtl8366rb: Support port 4 (WAN)
Linus Walleij
linus.walleij at linaro.org
Wed Aug 8 08:38:55 EDT 2018
The totally undocumented IO mode needs to be set to enumerator
0 to enable port 4 also known as WAN in most configurations,
for ordinary traffic. The 3 bits in the register come up as
010 after reset, but need to be set to 000.
The Realtek source code contains a name for these bits, but
no explanation of what the 8 different IO modes may be.
Set it to zero for the time being and drop a comment so
people know what is going on if they run into trouble. This
"mode zero" works fine with the D-Link DIR-685 with
RTL8366RB.
Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
drivers/net/dsa/rtl8366rb.c | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/drivers/net/dsa/rtl8366rb.c b/drivers/net/dsa/rtl8366rb.c
index 1e55b9bf8b56..a4d5049df692 100644
--- a/drivers/net/dsa/rtl8366rb.c
+++ b/drivers/net/dsa/rtl8366rb.c
@@ -48,6 +48,23 @@
#define RTL8366RB_SSCR2 0x0004
#define RTL8366RB_SSCR2_DROP_UNKNOWN_DA BIT(0)
+/* Port Mode Control registers */
+#define RTL8366RB_PMC0 0x0005
+#define RTL8366RB_PMC0_SPI BIT(0)
+#define RTL8366RB_PMC0_EN_AUTOLOAD BIT(1)
+#define RTL8366RB_PMC0_PROBE BIT(2)
+#define RTL8366RB_PMC0_DIS_BISR BIT(3)
+#define RTL8366RB_PMC0_ADCTEST BIT(4)
+#define RTL8366RB_PMC0_SRAM_DIAG BIT(5)
+#define RTL8366RB_PMC0_EN_SCAN BIT(6)
+#define RTL8366RB_PMC0_P4_IOMODE_SHIFT 7
+#define RTL8366RB_PMC0_P4_IOMODE_MASK GENMASK(9, 7)
+#define RTL8366RB_PMC0_P5_IOMODE_SHIFT 10
+#define RTL8366RB_PMC0_P5_IOMODE_MASK GENMASK(12, 10)
+#define RTL8366RB_PMC0_SDSMODE_SHIFT 13
+#define RTL8366RB_PMC0_SDSMODE_MASK GENMASK(15, 13)
+#define RTL8366RB_PMC1 0x0006
+
/* Port Mirror Control Register */
#define RTL8366RB_PMCR 0x0007
#define RTL8366RB_PMCR_SOURCE_PORT(a) (a)
@@ -860,6 +877,19 @@ static int rtl8366rb_setup(struct dsa_switch *ds)
if (ret)
return ret;
+ /* Port 4 setup: this enables Port 4, usually the WAN port,
+ * common PHY IO mode is apparently mode 0, and this is not what
+ * the port is initialized to. There is no explanation of the
+ * IO modes in the Realtek source code, if your WAN port is
+ * connected to something exotic such as fiber, then this might
+ * be worth experimenting with.
+ */
+ ret = regmap_update_bits(smi->map, RTL8366RB_PMC0,
+ RTL8366RB_PMC0_P4_IOMODE_MASK,
+ 0 << RTL8366RB_PMC0_P4_IOMODE_SHIFT);
+ if (ret)
+ return ret;
+
/* Discard VLAN tagged packets if the port is not a member of
* the VLAN with which the packets is associated.
*/
--
2.17.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list