[OpenWrt-Devel] [PATCH 4/4] ath79: add support for OCEDO Koala
David Bauer
mail at david-bauer.net
Mon Aug 6 10:21:04 EDT 2018
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail at david-bauer.net>
---
package/boot/uboot-envtools/files/ath79 | 1 +
.../ath79/base-files/etc/board.d/02_network | 1 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 4 +
.../linux/ath79/dts/qca9558_ocedo_koala.dts | 173 ++++++++++++++++++
target/linux/ath79/image/generic.mk | 10 +
5 files changed, 189 insertions(+)
create mode 100644 target/linux/ath79/dts/qca9558_ocedo_koala.dts
diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79
index 4d9d2e8fe0..aa0bf4514f 100644
--- a/package/boot/uboot-envtools/files/ath79
+++ b/package/boot/uboot-envtools/files/ath79
@@ -14,6 +14,7 @@ board=$(board_name)
case "$board" in
glinet,ar300m|\
+ocedo,koala|\
ocedo,raccoon|\
openmesh,om5p-ac-v2)
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x10000"
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index 0bc187a245..e333231638 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -13,6 +13,7 @@ ath79_setup_interfaces()
ucidef_set_interface_lan "eth0" "dhcp"
;;
"avm,fritz300e"|\
+ "ocedo,koala"|\
"ocedo,raccoon"|\
"pcs,cap324"|\
"tplink,re450-v2"|\
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 240a1bf1dd..c6d6c0157d 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -87,6 +87,10 @@ board=$(board_name)
case "$FIRMWARE" in
"ath10k/cal-pci-0000:00:00.0.bin")
case $board in
+ "ocedo,koala")
+ ath10kcal_extract "art" 20480 2116
+ ath10kcal_patch_mac $(mtd_get_mac_binary art 12)
+ ;;
"openmesh,om5p-ac-v2")
ath10kcal_extract "ART" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
diff --git a/target/linux/ath79/dts/qca9558_ocedo_koala.dts b/target/linux/ath79/dts/qca9558_ocedo_koala.dts
new file mode 100644
index 0000000000..e0d9680add
--- /dev/null
+++ b/target/linux/ath79/dts/qca9558_ocedo_koala.dts
@@ -0,0 +1,173 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca9557.dtsi"
+
+/ {
+ compatible = "ocedo,koala", "qca,qca9557";
+ model = "OCEDO Koala";
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ aliases {
+ led-status = &system;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power {
+ label = "koala:green:power";
+ gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ wifi2 {
+ label = "koala:yellow:wlan2";
+ gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ default-state = "off";
+ };
+
+ wifi5 {
+ label = "koala:red:wlan58";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ default-state = "off";
+ };
+
+ system: system {
+ label = "koala:blue:sys";
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <100>;
+
+ button at 0 {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&uart {
+ status = "okay";
+};
+
+&pll {
+ clocks = <&extosc>;
+};
+
+&spi {
+ status = "okay";
+ num-cs = <1>;
+
+ flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ uboot: partition at 0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x010000>;
+ };
+
+ partition at 50000 {
+ label = "firmware";
+ reg = <0x050000 0x740000>;
+ };
+
+ partition at 790000 {
+ label = "vendor";
+ reg = <0x790000 0x740000>;
+ read-only;
+ };
+
+ partition at ed0000 {
+ label = "data";
+ reg = <0xed0000 0x110000>;
+ read-only;
+ };
+
+ partition at fe0000 {
+ label = "id";
+ reg = <0xfe0000 0x010000>;
+ read-only;
+ };
+
+ art: partition at ff0000 {
+ label = "art";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+ mtd-mac-address = <&art 0x06>;
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy5: ethernet-phy at 5 {
+ reg = <5>;
+ phy-mode = "rgmii-rxid";
+
+ at803x-disable-smarteee;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ mtd-mac-address = <&art 0x00>;
+
+ phy-handle = <&phy5>;
+ phy-mode = "rgmii-rxid";
+
+ pll-data = <0xae000000 0xa0000101 0xa0001313>;
+
+ gmac-config {
+ device = <&gmac>;
+
+ rxdv-delay = <3>;
+ rxd-delay = <3>;
+ txen-delay = <0>;
+ txd-delay = <0>;
+ rgmii-enabled = <1>;
+ };
+};
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index a924fa90b0..f122afb8b1 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -49,6 +49,16 @@ define Device/glinet_ar300m_nor
endef
TARGET_DEVICES += glinet_ar300m_nor
+define Device/ocedo_koala
+ ATH_SOC := qca9558
+ DEVICE_TITLE := OCEDO Koala
+ DEVICE_PACKAGES := kmod-ath10k ath10k-firmware-qca988x
+ SUPPORTED_DEVICES += koala
+ IMAGE_SIZE := 7424k
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
+endef
+TARGET_DEVICES += ocedo_koala
+
define Device/ocedo_raccoon
ATH_SOC := ar9344
DEVICE_TITLE := OCEDO Raccoon
--
2.18.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list