[resend rfc v3] pwm: add BCM2835 PWM driver

[Thierry Reding]

On Thu, Sep 04, 2014 at 09:06:48AM -0600, Stephen Warren wrote:
> On 09/04/2014 04:05 AM, Bart Tanghe wrote:
> >No problem. Thanks for the feedback.
> >I've got some question below.
> >
> >On 2014-08-25 15:19, Thierry Reding wrote:
> >>Sorry for taking so long to reply to this, I had completely forgotten.
> >>
> >>On Mon, Apr 28, 2014 at 02:54:46PM +0200, Bart Tanghe wrote:
> >>>	Add some better error handling and Device table support
> >>>	Added Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt
> >>>	
> >>>Signed-off-by: Bart Tanghe <bart.tanghe at thomasmore.be>
> 
> >>>diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
> >>>index 22f2f28..20341a3 100644
> >>>--- a/drivers/pwm/Kconfig
> >>>+++ b/drivers/pwm/Kconfig
> >>>@@ -62,6 +62,18 @@ config PWM_ATMEL_TCB
> >>>  	  To compile this driver as a module, choose M here: the module
> >>>  	  will be called pwm-atmel-tcb.
> >>>
> >>>+config PWM_BCM2835
> >>>+	tristate "BCM2835 PWM support"
> >>>+	depends on MACH_BCM2835 || MACH_BCM2708
> >>>+	help
> >>>+	  PWM framework driver for BCM2835 controller (raspberry pi)
> >>
> >>I think the correct capitalization would be "Raspberry Pi".
> >>
> >>>+	  Only 1 channel is implemented.
> >>
> >>How many can it take? Why haven't all been implemented?
> >
> >BCM2835 can take 2 pwm channels.
> >I can implement 2 channels but can't physically test the second channel. Is that a problem?
> 
> I don't think that's a problem; I would expect the channels to be identical,
> so testing 1 should be fine.

Agreed. If it turns out not to work it can always be fixed.

> >>I notice that you never prepare or enable the clock here. Perhaps this
> >>isn't required because it's always on, but I think you should still call
> >>clk_prepare_enable() here (and clk_disable_unprepare() in .remove()) to
> >>make sure the driver is more portable.
> >The frequency can be minimized by a clock_divider ( the pwm clock is default disabled). this has to be done by
> >a clock driver, as mentioned in a previous comment by Stephen Warren.
> >
> >Any clock programming should be performed by a clock driver. We don't
> >have one of those upstream yet, mainly because it would rely on talking
> >to the firmware (running on the VideoCore) to manipulate the clocks, and
> >we don't have a firmware protocol driver either.
> >
> >Nowadays, I'm using a userspace program to change the clock_divider, but would like to implement this in a clock driver.
> >The clock hardware description isn't implemented in the datasheet. I can convert the userspace prog to a clock driver but this is very experimental.
> >If anyone has some suggestions?
> 
> Oh dear. It sounds like we need at least some form of clock driver for the
> platform then. I still don't think there's complete documentation for the
> HW, even though a lot of register docs were published which presumably cover
> the clock HW? Equally, given that the VC firmware assumes it owns most of
> the HW, it seems best to manipulate the clocks through the firmware
> interface rather than directly touching the HW. Unfortunately, I don't
> believe there's any ABI guarantee on the firmware interface. Perhaps we can
> get one?

Urgs... this VC firmware seems to be more of a headache that I thought
it was. How is this handled in other drivers? Surely PWM isn't the first
one that needs clocks?

> >>>+static const struct of_device_id bcm2835_pwm_of_match[] = {
> >>>+	{ .compatible = "bcrm,pwm-bcm2835", },
> >>
> >>s/bcrm/brcm/
> 
> Probably swap the order, so "brcm,bcm2835-pwm". That would be consistent
> with all the other HW on this SoC.

Yes, please.

Thierry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-rpi-kernel/attachments/20140926/e4aeb840/attachment.sig>