[PATCH V2 3/3] arm64: dts: rockchip: Add Orange Pi 5 Pro board support
Shawn Lin
shawn.lin at rock-chips.com
Wed Mar 4 21:19:47 PST 2026
在 2026/03/04 星期三 10:55, dennis at ausil.us 写道:
> From: Dennis Gilmore <dennis at ausil.us>
>
> Add device tree for the Xunlong Orange Pi 5 Pro (RK3588S). The Pro
> differs from the base Orange Pi 5 in the following ways:
>
> - No SPI NOR flash; eMMC module slot instead, you can optionally solder
> a SPI NOR fin place and turn off the eMMC
> - PCIe-attached NIC (pcie2x1l1) replaces the GMAC1 ethernet
> - PCIe NVMe slot (pcie2x1l2)
> - AP6256 WiFi (BCM43456) via SDIO with mmc-pwrseq
> - BCM4345C5 Bluetooth via uart9 with full RTS/CTS
> - Two-colour (blue/green) GPIO LED using modern color/function binding
> - audio is wired up differently
>
> Vendors description and links to schematics available:
> http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-5-Pro.html
>
> Signed-off-by: Dennis Gilmore <dennis at ausil.us>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../dts/rockchip/rk3588s-orangepi-5-pro.dts | 376 ++++++++++++++++++
> 2 files changed, 377 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 4d384f153c13..c99dca2ae9e7 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -214,6 +214,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-nanopi-r6c.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-odroid-m2.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5b.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5-pro.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-cm5-base.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-radxa-cm5-io.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-roc-pc.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts
> new file mode 100644
> index 000000000000..d656328c906d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts
> @@ -0,0 +1,376 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include "rk3588s-orangepi-5.dtsi"
> +
> +/ {
> + model = "Xunlong Orange Pi 5 Pro";
> + compatible = "xunlong,orangepi-5-pro", "rockchip,rk3588s";
> +
> + aliases {
> + /delete-property/ ethernet0;
> + mmc0 = &sdhci;
> + mmc1 = &sdmmc;
> + mmc2 = &sdio;
> + };
> +
> + /* Pro uses gpio-leds instead; pwm0 LED is not wired up */
> + /delete-node/ pwm-leds;
> +
> + /*
> + * Pro uses i2s2 (i2s2m1 mux) for audio, not i2s1. Recreate the sound
> + * card node pointing at i2s2_2ch instead.
> + */
> + /delete-node/ analog-sound;
> +
> + analog-sound {
> + compatible = "simple-audio-card";
> + pinctrl-names = "default";
> + pinctrl-0 = <&hp_detect>;
> + simple-audio-card,bitclock-master = <&masterdai>;
> + simple-audio-card,format = "i2s";
> + simple-audio-card,frame-master = <&masterdai>;
> + simple-audio-card,hp-det-gpios = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>;
> + simple-audio-card,mclk-fs = <256>;
> + simple-audio-card,name = "rockchip,es8388";
> + simple-audio-card,routing =
> + "Headphones", "LOUT1",
> + "Headphones", "ROUT1",
> + "LINPUT1", "Microphone Jack",
> + "RINPUT1", "Microphone Jack",
> + "LINPUT2", "Onboard Microphone",
> + "RINPUT2", "Onboard Microphone";
> + simple-audio-card,widgets =
> + "Microphone", "Microphone Jack",
> + "Microphone", "Onboard Microphone",
> + "Headphone", "Headphones";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&i2s2_2ch>;
> + };
> +
> + masterdai: simple-audio-card,codec {
> + sound-dai = <&es8388>;
> + system-clock-frequency = <12288000>;
> + };
> + };
> +
> + fan: pwm-fan {
> + compatible = "pwm-fan";
> + #cooling-cells = <2>;
> + cooling-levels = <0 50 100 150 200 255>;
> + fan-supply = <&vcc5v0_sys>;
> + pwms = <&pwm2 0 20000000 0>;
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&leds_rgb>;
> +
> + blue-led {
> + color = <LED_COLOR_ID_BLUE>;
> + function = LED_FUNCTION_STATUS;
> + gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> +
> + green-led {
> + color = <LED_COLOR_ID_GREEN>;
> + function = LED_FUNCTION_ACTIVITY;
> + gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "mmc0";
> + };
> + };
> +
> + vcc5v0_otg: regulator-vcc5v0-otg {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc5v0_otg_en>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <5000000>;
> + regulator-min-microvolt = <5000000>;
> + regulator-name = "vcc5v0_otg";
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + clocks = <&hym8563>;
> + clock-names = "ext_clock";
> + post-power-on-delay-ms = <200>;
> + reset-gpios = <&gpio0 RK_PD0 GPIO_ACTIVE_LOW>;
> + };
> +
> + vcc3v3_pcie20: regulator-vcc3v3-pcie20 {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpios = <&gpio3 RK_PB7 GPIO_ACTIVE_HIGH>;
> + regulator-boot-on;
> + regulator-max-microvolt = <3300000>;
> + regulator-min-microvolt = <3300000>;
> + regulator-name = "vcc3v3_pcie20";
> + startup-delay-us = <50000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc3v3_pcie_eth: regulator-vcc3v3-pcie-eth {
> + compatible = "regulator-fixed";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <3300000>;
> + regulator-min-microvolt = <3300000>;
> + regulator-name = "vcc3v3_pcie_eth";
> + vin-supply = <&vcc5v0_sys>;
> + };
> +};
> +
> +/* disable gmac1 as the pro has a PCIe attached NIC */
> +&gmac1 {
> + status = "disabled";
> +};
> +
> +/* 40-pin header pins 3/5 */
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1m4_xfer>;
> + status = "okay";
> +};
> +
> +/*
> + * Pro routes audio codec via i2c3 (not i2c6) and i2s2m1 (not i2s1m0).
> + * Delete the inherited es8388 node from i2c6 and redeclare it here.
> + */
> +/delete-node/ &es8388;
> +
> +&i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c3m0_xfer>;
> + status = "okay";
> +
> + es8388: audio-codec at 11 {
> + compatible = "everest,es8388", "everest,es8328";
> + reg = <0x11>;
> + #sound-dai-cells = <0>;
> + AVDD-supply = <&vcc_3v3_s0>;
> + DVDD-supply = <&vcc_1v8_s0>;
> + HPVDD-supply = <&vcc_3v3_s0>;
> + PVDD-supply = <&vcc_3v3_s0>;
> + assigned-clock-rates = <12288000>;
> + assigned-clocks = <&cru I2S2_2CH_MCLKOUT>;
> + clocks = <&cru I2S2_2CH_MCLKOUT>;
> + };
> +};
> +
> +/* 40-pin header pins 27/28 */
> +&i2c4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c4m3_xfer>;
> + status = "okay";
> +};
> +
> +/*
> + * i2s1_8ch uses i2s1m0 which occupies GPIO4_PA0 (CLKREQ#) and GPIO4_PA1
> + * (WAKE#) needed for the NVMe M.2 slot. Disable it; audio is on i2s2_2ch.
> + */
> +&i2s1_8ch {
> + status = "disabled";
> +};
> +
> +/* Audio codec on i2s2, m1 mux; add mclk pin to the base pinctrl */
> +&i2s2_2ch {
> + pinctrl-0 = <&i2s2m1_lrck &i2s2m1_mclk &i2s2m1_sclk
> + &i2s2m1_sdi &i2s2m1_sdo>;
> + status = "okay";
> +};
> +
> +&package_thermal {
> + polling-delay = <1000>;
> +
> + cooling-maps {
> + map0 {
> + trip = <&package_fan0>;
> + cooling-device = <&fan THERMAL_NO_LIMIT 1>;
> + };
> +
> + map1 {
> + trip = <&package_fan1>;
> + cooling-device = <&fan 2 THERMAL_NO_LIMIT>;
> + };
> + };
> +
> + trips {
> + package_fan0: package-fan0 {
> + hysteresis = <2000>;
> + temperature = <55000>;
> + type = "active";
> + };
> +
> + package_fan1: package-fan1 {
> + hysteresis = <2000>;
> + temperature = <65000>;
> + type = "active";
> + };
> + };
> +};
> +
> +/* NVMe */
> +&pcie2x1l1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie30x1m1_1_clkreqn &pcie30x1m1_1_waken>;
> + reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
> + supports-clkreq;
> + vpcie3v3-supply = <&vcc3v3_pcie_eth>;
I don't get this. NVMe M.2 slot uses power for eth?
> + status = "okay";
> +};
> +
> +/* NIC */
> +&pcie2x1l2 {
> + reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
> + vpcie3v3-supply = <&vcc3v3_pcie20>;
The same question as above.
> + status = "okay";
> +};
> +
> +&pinctrl {
> + bluetooth {
> + bt_wake_gpio: bt-wake-pin {
> + rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + bt_wake_host_irq: bt-wake-host-irq {
> + rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +
> + gpio-leds {
> + leds_rgb: leds-rgb {
> + rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>,
> + <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + usb {
> + vcc5v0_otg_en: vcc5v0-otg-en {
> + rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + wlan {
> + wifi_host_wake_irq: wifi-host-wake-irq {
> + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +};
> +
> +/* pwm0 pin conflicts with i2c4 pin 27 Pro */
> +&pwm0 {
> + status = "disabled";
> +};
> +
> +&pwm2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwm2m1_pins>;
> + status = "okay";
> +};
> +
> +&sdhci {
> + status = "okay";
> +};
> +
> +&sdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cap-sdio-irq;
> + disable-wp;
Please remove disable-wp for SDIO device.
> + keep-power-in-suspend;
> + max-frequency = <150000000>;
> + mmc-pwrseq = <&sdio_pwrseq>;
> + no-mmc;
> + no-sd;
> + non-removable;
> + sd-uhs-sdr104;
> + status = "okay";
> +
> + ap6256: wifi at 1 {
> + compatible = "brcm,bcm43456-fmac", "brcm,bcm4329-fmac";
> + reg = <1>;
> + interrupt-names = "host-wake";
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PA0 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_host_wake_irq>;
> + };
> +};
> +
> +&uart9 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart9m2_xfer &uart9m2_ctsn &uart9m2_rtsn>;
> + uart-has-rtscts;
> + status = "okay";
> +
> + bluetooth {
> + compatible = "brcm,bcm4345c5";
> + clocks = <&hym8563>;
> + clock-names = "lpo";
> + device-wakeup-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
> + interrupt-names = "host-wakeup";
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PC5 IRQ_TYPE_LEVEL_HIGH>;
> + max-speed = <1500000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&bt_wake_host_irq &bt_wake_gpio>;
> + shutdown-gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
> + vbat-supply = <&vcc_3v3_s3>;
> + vddio-supply = <&vcc_1v8_s3>;
> + };
> +};
> +
> +/* USB2 OTG PHY for usb_host0_xhci; phy-supply enables VBUS to USB3 Type-A port */
> +&u2phy0_otg {
> + phy-supply = <&vcc5v0_otg>;
> +};
> +
> +/* Pro has no FUSB302; the USB-C port is power delivery only */
> +/delete-node/ &usbc0;
> +
> +/*
> + * The Pro's USB-C port is power delivery only: no FUSB302, no data lines,
> + * no alt-mode switching. The parent DTSI enables usbdp_phy0 (status = "okay")
> + * and adds FUSB302 alt-mode/orientation properties; delete those here.
> + *
> + * dp-lane-mux = <0 1>: PHY lanes 0/1 are DP (physically routed to the
> + * LT8711UXD DP→HDMI2 bridge), lanes 2/3 are USB3 SuperSpeed (physically
> + * routed to the USB3 Type-A port P3). Without this property the driver
> + * defaults to USB-only mode and places USB3 on lanes 0/1, which do not
> + * reach the Type-A connector and makes the USB3 port non-functional.
> + */
> +&usbdp_phy0 {
> + rockchip,dp-lane-mux = <0 1>;
> + /delete-property/ mode-switch;
> + /delete-property/ orientation-switch;
> + /delete-property/ sbu1-dc-gpios;
> + /delete-property/ sbu2-dc-gpios;
> + /delete-node/ port;
> +};
> +
> +/* USB3 Type-A port*/
> +&usb_host0_xhci {
> + dr_mode = "host";
> + /delete-property/ usb-role-switch;
> + status = "okay";
> + /delete-node/ port;
> +};
> +
> +/*
> + * combphy2_psu is shared between usb_host2_xhci (USB3) and pcie2x1l1 (PCIe).
> + * Disable USB3 so the PHY can be used for the NVMe M.2 slot.
> + */
> +&usb_host2_xhci {
> + status = "disabled";
> +};
>
More information about the Linux-rockchip
mailing list