[PATCH 07/11] arm64: dts: rockchip: Add USB nodes for RK3528

[Jonas Karlman]

Rockchip RK3528 has one USB 3.0 DWC3 controller, a USB 2.0 EHCI/OHCI
controller and uses a USB2PHY for USB 2.0. The DWC3 controller may also
use the Naneng Combo PHY for USB3.

Add device tree nodes to describe these USB controllers along with the
USB 2.0 PHYs.

Signed-off-by: Jonas Karlman <jonas at kwiboo.se>
---
The DWC3 node does not contain any default phys because out of current
and pending supported boards only one board, ROCK 2A, can use USB3.
Remaining boards use the Naneng Combo PHY for PCIe instead of USB3.
---
 arch/arm64/boot/dts/rockchip/rk3528.dtsi | 76 ++++++++++++++++++++++++
 1 file changed, 76 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3528.dtsi b/arch/arm64/boot/dts/rockchip/rk3528.dtsi
index 85bc3f5aa2c7..3e51a3f51e05 100644
--- a/arch/arm64/boot/dts/rockchip/rk3528.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3528.dtsi
@@ -243,6 +243,29 @@ soc {
 		#address-cells = <2>;
 		#size-cells = <2>;
 
+		usb_host0_xhci: usb at fe500000 {
+			compatible = "rockchip,rk3528-dwc3", "snps,dwc3";
+			reg = <0x0 0xfe500000 0x0 0x400000>;
+			clocks = <&cru CLK_REF_USB3OTG>,
+				 <&cru CLK_SUSPEND_USB3OTG>,
+				 <&cru ACLK_USB3OTG>;
+			clock-names = "ref_clk", "suspend_clk", "bus_clk";
+			interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&power RK3528_PD_VPU>;
+			resets = <&cru SRST_A_USB3OTG>;
+			dr_mode = "otg";
+			phy_type = "utmi_wide";
+			snps,dis_enblslpm_quirk;
+			snps,dis-del-phy-power-chg-quirk;
+			snps,dis-tx-ipgap-linecheck-quirk;
+			snps,dis-u1-entry-quirk;
+			snps,dis-u2-entry-quirk;
+			snps,dis-u2-freeclk-exists-quirk;
+			snps,parkmode-disable-hs-quirk;
+			snps,parkmode-disable-ss-quirk;
+			status = "disabled";
+		};
+
 		gic: interrupt-controller at fed01000 {
 			compatible = "arm,gic-400";
 			reg = <0x0 0xfed01000 0 0x1000>,
@@ -256,6 +279,30 @@ gic: interrupt-controller at fed01000 {
 			#interrupt-cells = <3>;
 		};
 
+		usb_host0_ehci: usb at ff100000 {
+			compatible = "generic-ehci";
+			reg = <0x0 0xff100000 0x0 0x40000>;
+			clocks = <&cru HCLK_USBHOST>, <&cru HCLK_USBHOST_ARB>,
+				 <&u2phy>;
+			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&u2phy_host>;
+			phy-names = "usb";
+			power-domains = <&power RK3528_PD_VO>;
+			status = "disabled";
+		};
+
+		usb_host0_ohci: usb at ff140000 {
+			compatible = "generic-ohci";
+			reg = <0x0 0xff140000 0x0 0x40000>;
+			clocks = <&cru HCLK_USBHOST>, <&cru HCLK_USBHOST_ARB>,
+				 <&u2phy>;
+			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&u2phy_host>;
+			phy-names = "usb";
+			power-domains = <&power RK3528_PD_VO>;
+			status = "disabled";
+		};
+
 		qos_crypto_a: qos at ff200000 {
 			compatible = "rockchip,rk3528-qos", "syscon";
 			reg = <0x0 0xff200000 0x0 0x20>;
@@ -1109,6 +1156,35 @@ dmac: dma-controller at ffd60000 {
 			#dma-cells = <1>;
 			arm,pl330-periph-burst;
 		};
+
+		u2phy: usb2phy at ffdf0000 {
+			compatible = "rockchip,rk3528-usb2phy";
+			reg = <0x0 0xffdf0000 0x0 0x10000>;
+			clocks = <&cru CLK_REF_USBPHY>, <&cru PCLK_USBPHY>;
+			clock-names = "phyclk", "pclk";
+			#clock-cells = <0>;
+			clock-output-names = "clk_usbphy_480m";
+			power-domains = <&power RK3528_PD_VO>;
+			rockchip,usbgrf = <&vo_grf>;
+			status = "disabled";
+
+			u2phy_otg: otg-port {
+				interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "otg-bvalid", "otg-id",
+						  "linestate";
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+
+			u2phy_host: host-port {
+				interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "linestate";
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+		};
 	};
 };
 
-- 
2.50.1