[PATCH v2 5/5] arm64: dts: rockchip: Enable more power domains for RK3528
Jonas Karlman
jonas at kwiboo.se
Wed Jul 23 01:56:47 PDT 2025
Describe device power-domains and enable the PD_RKVENC, PD_VO and PD_VPU
power-domains on RK3528.
The PD_RKVDEC is used by RKVDEC and DDRPHY CRU, and is kept disabled to
prevent a full system reset trying to read the rate of the SCMI_CLK_DDR
clock.
Signed-off-by: Jonas Karlman <jonas at kwiboo.se>
---
Changes in v2:
- Add power-domains for spi nodes
- Rebased on top of next-20250722
---
arch/arm64/boot/dts/rockchip/rk3528.dtsi | 30 +++++++++++++++++++++---
1 file changed, 27 insertions(+), 3 deletions(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3528.dtsi b/arch/arm64/boot/dts/rockchip/rk3528.dtsi
index 54fa8089c4d3..85bc3f5aa2c7 100644
--- a/arch/arm64/boot/dts/rockchip/rk3528.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3528.dtsi
@@ -155,6 +155,7 @@ gpio1: gpio at ffaf0000 {
gpio-ranges = <&pinctrl 0 32 32>;
interrupt-controller;
#interrupt-cells = <2>;
+ power-domains = <&power RK3528_PD_VPU>;
};
gpio2: gpio at ffb00000 {
@@ -167,6 +168,7 @@ gpio2: gpio at ffb00000 {
gpio-ranges = <&pinctrl 0 64 32>;
interrupt-controller;
#interrupt-cells = <2>;
+ power-domains = <&power RK3528_PD_VO>;
};
gpio3: gpio at ffb10000 {
@@ -179,6 +181,7 @@ gpio3: gpio at ffb10000 {
gpio-ranges = <&pinctrl 0 96 32>;
interrupt-controller;
#interrupt-cells = <2>;
+ power-domains = <&power RK3528_PD_VPU>;
};
gpio4: gpio at ffb20000 {
@@ -191,6 +194,7 @@ gpio4: gpio at ffb20000 {
gpio-ranges = <&pinctrl 0 128 32>;
interrupt-controller;
#interrupt-cells = <2>;
+ power-domains = <&power RK3528_PD_RKVENC>;
};
};
@@ -501,7 +505,6 @@ power-domain at RK3528_PD_RKVENC {
reg = <RK3528_PD_RKVENC>;
pm_qos = <&qos_rkvenc>;
#power-domain-cells = <0>;
- status = "disabled";
};
power-domain at RK3528_PD_VO {
reg = <RK3528_PD_VO>;
@@ -515,7 +518,6 @@ power-domain at RK3528_PD_VO {
<&qos_vdpp>,
<&qos_vop>;
#power-domain-cells = <0>;
- status = "disabled";
};
power-domain at RK3528_PD_VPU {
reg = <RK3528_PD_VPU>;
@@ -529,7 +531,6 @@ power-domain at RK3528_PD_VPU {
<&qos_usb3otg>,
<&qos_vpu>;
#power-domain-cells = <0>;
- status = "disabled";
};
};
};
@@ -571,6 +572,7 @@ spi0: spi at ff9c0000 {
interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmac 25>, <&dmac 24>;
dma-names = "tx", "rx";
+ power-domains = <&power RK3528_PD_RKVENC>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -585,6 +587,7 @@ spi1: spi at ff9d0000 {
interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmac 31>, <&dmac 30>;
dma-names = "tx", "rx";
+ power-domains = <&power RK3528_PD_VPU>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -609,6 +612,7 @@ uart1: serial at ff9f8000 {
clock-names = "baudclk", "apb_pclk";
interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmac 11>, <&dmac 10>;
+ power-domains = <&power RK3528_PD_RKVENC>;
reg-io-width = <4>;
reg-shift = <2>;
status = "disabled";
@@ -621,6 +625,7 @@ uart2: serial at ffa00000 {
clock-names = "baudclk", "apb_pclk";
interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmac 13>, <&dmac 12>;
+ power-domains = <&power RK3528_PD_VPU>;
reg-io-width = <4>;
reg-shift = <2>;
status = "disabled";
@@ -633,6 +638,7 @@ uart3: serial at ffa08000 {
clock-names = "baudclk", "apb_pclk";
interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmac 15>, <&dmac 14>;
+ power-domains = <&power RK3528_PD_RKVENC>;
reg-io-width = <4>;
reg-shift = <2>;
status = "disabled";
@@ -645,6 +651,7 @@ uart4: serial at ffa10000 {
clock-names = "baudclk", "apb_pclk";
interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmac 17>, <&dmac 16>;
+ power-domains = <&power RK3528_PD_VO>;
reg-io-width = <4>;
reg-shift = <2>;
status = "disabled";
@@ -657,6 +664,7 @@ uart5: serial at ffa18000 {
clock-names = "baudclk", "apb_pclk";
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmac 19>, <&dmac 18>;
+ power-domains = <&power RK3528_PD_VPU>;
reg-io-width = <4>;
reg-shift = <2>;
status = "disabled";
@@ -669,6 +677,7 @@ uart6: serial at ffa20000 {
clock-names = "baudclk", "apb_pclk";
interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmac 21>, <&dmac 20>;
+ power-domains = <&power RK3528_PD_VPU>;
reg-io-width = <4>;
reg-shift = <2>;
status = "disabled";
@@ -681,6 +690,7 @@ uart7: serial at ffa28000 {
clock-names = "baudclk", "apb_pclk";
interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmac 23>, <&dmac 22>;
+ power-domains = <&power RK3528_PD_VPU>;
reg-io-width = <4>;
reg-shift = <2>;
status = "disabled";
@@ -693,6 +703,7 @@ i2c0: i2c at ffa50000 {
clocks = <&cru CLK_I2C0>, <&cru PCLK_I2C0>;
clock-names = "i2c", "pclk";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&power RK3528_PD_RKVENC>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -705,6 +716,7 @@ i2c1: i2c at ffa58000 {
clocks = <&cru CLK_I2C1>, <&cru PCLK_I2C1>;
clock-names = "i2c", "pclk";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&power RK3528_PD_RKVENC>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -731,6 +743,7 @@ i2c3: i2c at ffa68000 {
clocks = <&cru CLK_I2C3>, <&cru PCLK_I2C3>;
clock-names = "i2c", "pclk";
interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&power RK3528_PD_VPU>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -745,6 +758,7 @@ i2c4: i2c at ffa70000 {
interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&i2c4_xfer>;
+ power-domains = <&power RK3528_PD_VO>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -757,6 +771,7 @@ i2c5: i2c at ffa78000 {
clocks = <&cru CLK_I2C5>, <&cru PCLK_I2C5>;
clock-names = "i2c", "pclk";
interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&power RK3528_PD_VPU>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -769,6 +784,7 @@ i2c6: i2c at ffa80000 {
clocks = <&cru CLK_I2C6>, <&cru PCLK_I2C6>;
clock-names = "i2c", "pclk";
interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&power RK3528_PD_VPU>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -783,6 +799,7 @@ i2c7: i2c at ffa88000 {
interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&i2c7_xfer>;
+ power-domains = <&power RK3528_PD_VO>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -874,6 +891,7 @@ saradc: adc at ffae0000 {
clocks = <&cru CLK_SARADC>, <&cru PCLK_SARADC>;
clock-names = "saradc", "apb_pclk";
interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&power RK3528_PD_VPU>;
resets = <&cru SRST_P_SARADC>;
reset-names = "saradc-apb";
#io-channel-cells = <1>;
@@ -894,6 +912,7 @@ gmac0: ethernet at ffbd0000 {
interrupt-names = "macirq", "eth_wake_irq";
phy-handle = <&rmii0_phy>;
phy-mode = "rmii";
+ power-domains = <&power RK3528_PD_VO>;
resets = <&cru SRST_A_MAC_VO>;
reset-names = "stmmaceth";
rockchip,grf = <&vo_grf>;
@@ -952,6 +971,7 @@ gmac1: ethernet at ffbe0000 {
interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq", "eth_wake_irq";
+ power-domains = <&power RK3528_PD_VPU>;
resets = <&cru SRST_A_MAC>;
reset-names = "stmmaceth";
rockchip,grf = <&vpu_grf>;
@@ -1002,6 +1022,7 @@ sdhci: mmc at ffbf0000 {
pinctrl-names = "default";
pinctrl-0 = <&emmc_bus8>, <&emmc_clk>, <&emmc_cmd>,
<&emmc_strb>;
+ power-domains = <&power RK3528_PD_VPU>;
resets = <&cru SRST_C_EMMC>, <&cru SRST_H_EMMC>,
<&cru SRST_A_EMMC>, <&cru SRST_B_EMMC>,
<&cru SRST_T_EMMC>;
@@ -1023,6 +1044,7 @@ sdio0: mmc at ffc10000 {
max-frequency = <200000000>;
pinctrl-names = "default";
pinctrl-0 = <&sdio0_bus4>, <&sdio0_clk>, <&sdio0_cmd>;
+ power-domains = <&power RK3528_PD_VPU>;
resets = <&cru SRST_H_SDIO0>;
reset-names = "reset";
status = "disabled";
@@ -1042,6 +1064,7 @@ sdio1: mmc at ffc20000 {
max-frequency = <200000000>;
pinctrl-names = "default";
pinctrl-0 = <&sdio1_bus4>, <&sdio1_clk>, <&sdio1_cmd>;
+ power-domains = <&power RK3528_PD_VPU>;
resets = <&cru SRST_H_SDIO1>;
reset-names = "reset";
status = "disabled";
@@ -1062,6 +1085,7 @@ sdmmc: mmc at ffc30000 {
pinctrl-names = "default";
pinctrl-0 = <&sdmmc_bus4>, <&sdmmc_clk>, <&sdmmc_cmd>,
<&sdmmc_det>;
+ power-domains = <&power RK3528_PD_VO>;
resets = <&cru SRST_H_SDMMC0>;
reset-names = "reset";
rockchip,default-sample-phase = <90>;
--
2.50.1
More information about the Linux-rockchip
mailing list