[PATCH 4/6] arm64: dts: rockchip: Add ArmSoM Sige1

Chukun Pan amadeus at jmu.edu.cn
Wed Jul 9 00:00:03 PDT 2025


Hi,

> +	vcc5v0_usb1_host: regulator-5v0-vcc-usb1-host {
> +		compatible = "regulator-fixed";
> ...
> +		regulator-always-on;
> +		regulator-boot-on;
> ...
> +	vcc5v0_usb2_host: regulator-5v0-vcc-usb2-host {
> +		regulator-always-on;
> +		regulator-boot-on;
> ...

I think these two regulators do not need boot-on?

> +	rfkill {
> +		compatible = "rfkill-gpio";
> +		label = "rfkill-wlan";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&wifi_reg_on_h>;
> +		radio-type = "wlan";
> +		shutdown-gpios = <&gpio1 RK_PA6 GPIO_ACTIVE_HIGH>;
> +	};

Why not use mmc-pwrseq instead of rfkill?

> +	rfkill-bt {
> +		compatible = "rfkill-gpio";
> +		label = "rfkill-bt";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&bt_reg_on_h>;
> +		radio-type = "bluetooth";
> +		shutdown-gpios = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>;
> +	};

Why not use shutdown-gpios of bcm43438-bt?

> +&i2c0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c0m0_xfer>;
> +	status = "okay";
> +
> +	hym8563: rtc at 51 {
> +		compatible = "haoyu,hym8563";
> +		reg = <0x51>;
> +		#clock-cells = <0>;
> +		clock-output-names = "hym8563";

CLKOUT pin is not connected.

> +&sdio0 {
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	cap-sdio-irq;
> +	disable-wp;
> +	keep-power-in-suspend;
> +	no-mmc;
> +	no-sd;
> +	non-removable;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sdio0_bus4>, <&sdio0_clk>, <&sdio0_cmd>, <&clkm1_32k_out>;

I recommend using clkm1_32k_out at the sdio-pwrseq node.

> +	sd-uhs-sdr104;
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&vcc_1v8>;
> +	status = "okay";

Maybe `brcm,bcm4329-fmac` nodes can be added here?

> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart2m1_xfer>, <&uart2m1_ctsn>, <&uart2m1_rtsn>;
> +	uart-has-rtscts;
> +	status = "okay";

You can add `brcm,bcm43438-bt` nodes here:

	bluetooth {
		compatible = "brcm,bcm43438-bt";
		device-wakeup-gpios = <&gpio3 RK_PC3 GPIO_ACTIVE_HIGH>;
		host-wakeup-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_HIGH>;
		shutdown-gpios = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>;
		...
	};

Thanks,
Chukun

--
2.25.1




More information about the Linux-rockchip mailing list