[PATCH v2] arm64: dts: rockchip: enable both 2.5GbE ports on Rock 5T

[Nicolas Frattaroli]

On Thursday, 18 December 2025 07:27:06 Central European Standard Time Martin Holovský (Probably Nothing s.r.o.) wrote:
> The Radxa Rock 5T board features two RTL8125B 2.5GbE Ethernet controllers
> connected via PCIe lanes pcie2x1l0 (fe170000) and pcie2x1l2 (fe190000).
> Currently only one interface is functional because the PCIe controller
> nodes lack the necessary reset GPIO configuration.
> 
> Without the reset-gpios property, the RTL8125B PHYs remain in reset state
> and are not enumerated by the PCIe bus. This results in only one Ethernet
> interface being detected, or none at all depending on U-Boot initialization.
> 
> This patch adds the missing configuration for both PCIe controllers:
> - Enables both pcie2x1l0 and pcie2x1l2 nodes (status = "okay")
> - Configures reset GPIOs (GPIO4_PA5 and GPIO3_PB0 respectively)
> - Adds corresponding pinctrl definitions
> 
> With this change, both 2.5GbE interfaces are properly detected and
> functional on the Rock 5T.
> 
> Tested on Radxa Rock 5T v1.2 running Linux 6.12.
> 
> Signed-off-by: Martin Holovsky <mh at probably.group>
> ---
> Changes in v2:
> - Sorted pcie nodes alphanumerically
> - Sorted pinctrl nodes alphanumerically
> - Added Signed-off-by line
> 
>  .../boot/dts/rockchip/rk3588-rock-5t.dts      | 28 +++++++++++++++++++
>  1 file changed, 28 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588-rock-5t.dts b/arch/arm64/boot/dts/rockchip/rk3588-rock-5t.dts
> index 0dd90c744380..aeb8e0d42f09 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3588-rock-5t.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3588-rock-5t.dts
> @@ -68,10 +68,24 @@ &pcie2x1l1 {
>  	reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
>  	status = "okay";
>  };
>  
> +&pcie2x1l0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie2_0_rst>;
> +	reset-gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
> +	status = "okay";
> +};
> +
> +&pcie2x1l2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie2_2_rst>;
> +	reset-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_HIGH>;
> +	status = "okay";
> +};
> +
>  &pcie30phy {
>  	data-lanes = <1 1 2 2>;
>  };
> @@ -101,6 +115,14 @@ pcie2 {
> +		pcie2_0_rst: pcie2-0-rst {
> +			rockchip,pins = <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
>  		pcie2_1_rst: pcie2-1-rst {
>  			rockchip,pins = <4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
>  		};
> +
> +		pcie2_2_rst: pcie2-2-rst {
> +			rockchip,pins = <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
>  		pcie2_0_vcc3v3_en: pcie2-0-vcc-en {
>  			rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
>  		};
> 

This stuff is already in rk3588-rock-5b-5bp-5t.dtsi. Ergo, this patch
does nothing at all. What are you actually trying to solve?

Heiko, please don't apply this.

Kind regards,
Nicolas Frattaroli