[PATCH v3 2/2] pinctrl: rockchip: Add rk3576 pinctrl support
Heiko Stübner
heiko at sntech.de
Thu Aug 15 07:05:08 PDT 2024
Am Donnerstag, 15. August 2024, 00:30:39 CEST schrieb Detlev Casanova:
> From: Steven Liu <steven.liu at rock-chips.com>
>
> Add support for the 5 rk3576 GPIO banks.
>
> This also adds support for optionnal support of the sys-grf syscon,
only one "n" in optional
> used for i3c software controlled weak pull-up.
>
> Signed-off-by: Steven Liu <steven.liu at rock-chips.com>
> [rebase, reword commit message]
> Signed-off-by: Detlev Casanova <detlev.casanova at collabora.com>
> ---
> drivers/pinctrl/pinctrl-rockchip.c | 228 +++++++++++++++++++++++++++++
> drivers/pinctrl/pinctrl-rockchip.h | 2 +
> 2 files changed, 230 insertions(+)
>
> diff --git a/drivers/pinctrl/pinctrl-rockchip.c b/drivers/pinctrl/pinctrl-rockchip.c
> index 0eacaf10c640f..110ed81d650be 100644
> --- a/drivers/pinctrl/pinctrl-rockchip.c
> +++ b/drivers/pinctrl/pinctrl-rockchip.c
> @@ -84,6 +84,27 @@
> }, \
> }
>
> +#define PIN_BANK_IOMUX_FLAGS_OFFSET_PULL_FLAGS(id, pins, label, iom0, \
> + iom1, iom2, iom3, \
> + offset0, offset1, \
> + offset2, offset3, pull0, \
> + pull1, pull2, pull3) \
> + { \
> + .bank_num = id, \
> + .nr_pins = pins, \
> + .name = label, \
> + .iomux = { \
> + { .type = iom0, .offset = offset0 }, \
> + { .type = iom1, .offset = offset1 }, \
> + { .type = iom2, .offset = offset2 }, \
> + { .type = iom3, .offset = offset3 }, \
> + }, \
> + .pull_type[0] = pull0, \
> + .pull_type[1] = pull1, \
> + .pull_type[2] = pull2, \
> + .pull_type[3] = pull3, \
> + }
> +
> #define PIN_BANK_DRV_FLAGS(id, pins, label, type0, type1, type2, type3) \
> { \
> .bank_num = id, \
> @@ -1120,6 +1141,11 @@ static int rockchip_get_mux(struct rockchip_pin_bank *bank, int pin)
> if (bank->recalced_mask & BIT(pin))
> rockchip_get_recalced_mux(bank, pin, ®, &bit, &mask);
>
> + if (ctrl->type == RK3576) {
> + if ((bank->bank_num == 0) && (pin >= RK_PB4) && (pin <= RK_PB7))
> + reg += 0x1FF4; /* GPIO0_IOC_GPIO0B_IOMUX_SEL_H */
0x1ff4 in lower case please
> + }
> +
> if (ctrl->type == RK3588) {
> if (bank->bank_num == 0) {
> if ((pin >= RK_PB4) && (pin <= RK_PD7)) {
> @@ -1193,6 +1219,7 @@ static int rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
> struct device *dev = info->dev;
> int iomux_num = (pin / 8);
> struct regmap *regmap;
> + struct regmap *regmap_sys;
> int reg, ret, mask, mux_type;
> u8 bit;
> u32 data, rmask, route_location, route_reg, route_val;
> @@ -1213,6 +1240,8 @@ static int rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
> else
> regmap = info->regmap_base;
>
> + regmap_sys = info->regmap_sys_grf;
> +
> /* get basic quadrupel of mux registers and the correct reg inside */
> mux_type = bank->iomux[iomux_num].type;
> reg = bank->iomux[iomux_num].offset;
> @@ -1234,6 +1263,20 @@ static int rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
> if (bank->recalced_mask & BIT(pin))
> rockchip_get_recalced_mux(bank, pin, ®, &bit, &mask);
>
> + if (ctrl->type == RK3576) {
> + if ((bank->bank_num == 0) && (pin >= RK_PB4) && (pin <= RK_PB7))
> + reg += 0x1FF4; /* GPIO0_IOC_GPIO0B_IOMUX_SEL_H */
0x1ff4 please
> + /* i3c0 weakpull controlled by software */
> + if (((bank->bank_num == 0) && (pin == RK_PC5) && (mux == 0xb)) ||
> + ((bank->bank_num == 1) && (pin == RK_PD1) && (mux == 0xa)))
> + regmap_update_bits(regmap_sys, 0x4, 0xc000c0, 0xc000c0);
> + /* i3c1 weakpull controlled by software */
> + if (((bank->bank_num == 2) && (pin == RK_PA5) && (mux == 0xe)) ||
> + ((bank->bank_num == 2) && (pin == RK_PD6) && (mux == 0xc)) ||
> + ((bank->bank_num == 3) && (pin == RK_PD1) && (mux == 0xb)))
> + regmap_update_bits(regmap_sys, 0x4, 0x3000300, 0x3000300);
this setting belongs into drivers/soc/rockchip/grf.c .
You want to decide that the i3c controller has no say over the pull
settings, but instead pinctrl should always be in control.
Such default system-wide settings should not clutter up the pinctrl
driver please. The grf-"driver" exists for exactly that case.
That way you also don't need the additional grf-handling here and
in the dt-binding.
> + }
> +
> if (ctrl->type == RK3588) {
> if (bank->bank_num == 0) {
> if ((pin >= RK_PB4) && (pin <= RK_PD7)) {
> @@ -2038,6 +2081,142 @@ static int rk3568_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
> return 0;
> }
>
> +#define RK3576_DRV_BITS_PER_PIN 4
> +#define RK3576_DRV_PINS_PER_REG 4
> +#define RK3576_DRV_GPIO0_AL_OFFSET 0x10
> +#define RK3576_DRV_GPIO0_BH_OFFSET 0x2014
> +#define RK3576_DRV_GPIO1_OFFSET 0x6020
> +#define RK3576_DRV_GPIO2_OFFSET 0x6040
> +#define RK3576_DRV_GPIO3_OFFSET 0x6060
> +#define RK3576_DRV_GPIO4_AL_OFFSET 0x6080
> +#define RK3576_DRV_GPIO4_CL_OFFSET 0xA090
> +#define RK3576_DRV_GPIO4_DL_OFFSET 0xB098
> +
> +static int rk3576_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
> + int pin_num, struct regmap **regmap,
> + int *reg, u8 *bit)
> +{
> + struct rockchip_pinctrl *info = bank->drvdata;
> +
> + *regmap = info->regmap_base;
> +
> + if (bank->bank_num == 0 && pin_num < 12)
> + *reg = RK3576_DRV_GPIO0_AL_OFFSET;
> + else if (bank->bank_num == 0)
> + *reg = RK3576_DRV_GPIO0_BH_OFFSET - 0xc;
> + else if (bank->bank_num == 1)
> + *reg = RK3576_DRV_GPIO1_OFFSET;
> + else if (bank->bank_num == 2)
> + *reg = RK3576_DRV_GPIO2_OFFSET;
> + else if (bank->bank_num == 3)
> + *reg = RK3576_DRV_GPIO3_OFFSET;
> + else if (bank->bank_num == 4 && pin_num < 16)
> + *reg = RK3576_DRV_GPIO4_AL_OFFSET;
> + else if (bank->bank_num == 4 && pin_num < 24)
> + *reg = RK3576_DRV_GPIO4_CL_OFFSET - 0x10;
> + else if (bank->bank_num == 4)
> + *reg = RK3576_DRV_GPIO4_DL_OFFSET - 0x18;
> + else
> + dev_err(info->dev, "unsupported bank_num %d\n", bank->bank_num);
> +
> + *reg += ((pin_num / RK3576_DRV_PINS_PER_REG) * 4);
> + *bit = pin_num % RK3576_DRV_PINS_PER_REG;
> + *bit *= RK3576_DRV_BITS_PER_PIN;
> +
> + return 0;
> +}
> +
> +#define RK3576_PULL_BITS_PER_PIN 2
> +#define RK3576_PULL_PINS_PER_REG 8
> +#define RK3576_PULL_GPIO0_AL_OFFSET 0x20
> +#define RK3576_PULL_GPIO0_BH_OFFSET 0x2028
> +#define RK3576_PULL_GPIO1_OFFSET 0x6110
> +#define RK3576_PULL_GPIO2_OFFSET 0x6120
> +#define RK3576_PULL_GPIO3_OFFSET 0x6130
> +#define RK3576_PULL_GPIO4_AL_OFFSET 0x6140
> +#define RK3576_PULL_GPIO4_CL_OFFSET 0xA148
> +#define RK3576_PULL_GPIO4_DL_OFFSET 0xB14C
> +
> +static int rk3576_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
> + int pin_num, struct regmap **regmap,
> + int *reg, u8 *bit)
> +{
> + struct rockchip_pinctrl *info = bank->drvdata;
> +
> + *regmap = info->regmap_base;
> +
> + if (bank->bank_num == 0 && pin_num < 12)
> + *reg = RK3576_PULL_GPIO0_AL_OFFSET;
> + else if (bank->bank_num == 0)
> + *reg = RK3576_PULL_GPIO0_BH_OFFSET - 0x4;
> + else if (bank->bank_num == 1)
> + *reg = RK3576_PULL_GPIO1_OFFSET;
> + else if (bank->bank_num == 2)
> + *reg = RK3576_PULL_GPIO2_OFFSET;
> + else if (bank->bank_num == 3)
> + *reg = RK3576_PULL_GPIO3_OFFSET;
> + else if (bank->bank_num == 4 && pin_num < 16)
> + *reg = RK3576_PULL_GPIO4_AL_OFFSET;
> + else if (bank->bank_num == 4 && pin_num < 24)
> + *reg = RK3576_PULL_GPIO4_CL_OFFSET - 0x8;
> + else if (bank->bank_num == 4)
> + *reg = RK3576_PULL_GPIO4_DL_OFFSET - 0xc;
> + else
> + dev_err(info->dev, "unsupported bank_num %d\n", bank->bank_num);
> +
> + *reg += ((pin_num / RK3576_PULL_PINS_PER_REG) * 4);
> + *bit = pin_num % RK3576_PULL_PINS_PER_REG;
> + *bit *= RK3576_PULL_BITS_PER_PIN;
> +
> + return 0;
> +}
> +
> +#define RK3576_SMT_BITS_PER_PIN 1
> +#define RK3576_SMT_PINS_PER_REG 8
> +#define RK3576_SMT_GPIO0_AL_OFFSET 0x30
> +#define RK3576_SMT_GPIO0_BH_OFFSET 0x2040
> +#define RK3576_SMT_GPIO1_OFFSET 0x6210
> +#define RK3576_SMT_GPIO2_OFFSET 0x6220
> +#define RK3576_SMT_GPIO3_OFFSET 0x6230
> +#define RK3576_SMT_GPIO4_AL_OFFSET 0x6240
> +#define RK3576_SMT_GPIO4_CL_OFFSET 0xA248
> +#define RK3576_SMT_GPIO4_DL_OFFSET 0xB24C
> +
> +static int rk3576_calc_schmitt_reg_and_bit(struct rockchip_pin_bank *bank,
> + int pin_num,
> + struct regmap **regmap,
> + int *reg, u8 *bit)
> +{
> + struct rockchip_pinctrl *info = bank->drvdata;
> +
> + *regmap = info->regmap_base;
> +
> + if (bank->bank_num == 0 && pin_num < 12)
> + *reg = RK3576_SMT_GPIO0_AL_OFFSET;
> + else if (bank->bank_num == 0)
> + *reg = RK3576_SMT_GPIO0_BH_OFFSET - 0x4;
> + else if (bank->bank_num == 1)
> + *reg = RK3576_SMT_GPIO1_OFFSET;
> + else if (bank->bank_num == 2)
> + *reg = RK3576_SMT_GPIO2_OFFSET;
> + else if (bank->bank_num == 3)
> + *reg = RK3576_SMT_GPIO3_OFFSET;
> + else if (bank->bank_num == 4 && pin_num < 16)
> + *reg = RK3576_SMT_GPIO4_AL_OFFSET;
> + else if (bank->bank_num == 4 && pin_num < 24)
> + *reg = RK3576_SMT_GPIO4_CL_OFFSET - 0x8;
> + else if (bank->bank_num == 4)
> + *reg = RK3576_SMT_GPIO4_DL_OFFSET - 0xc;
> + else
> + dev_err(info->dev, "unsupported bank_num %d\n", bank->bank_num);
> +
> + *reg += ((pin_num / RK3576_SMT_PINS_PER_REG) * 4);
> + *bit = pin_num % RK3576_SMT_PINS_PER_REG;
> + *bit *= RK3576_SMT_BITS_PER_PIN;
> +
> + return 0;
> +}
> +
> #define RK3588_PMU1_IOC_REG (0x0000)
> #define RK3588_PMU2_IOC_REG (0x4000)
> #define RK3588_BUS_IOC_REG (0x8000)
> @@ -2332,6 +2511,10 @@ static int rockchip_set_drive_perpin(struct rockchip_pin_bank *bank,
> rmask_bits = RK3568_DRV_BITS_PER_PIN;
> ret = (1 << (strength + 1)) - 1;
> goto config;
> + } else if (ctrl->type == RK3576) {
> + rmask_bits = RK3576_DRV_BITS_PER_PIN;
> + ret = ((strength & BIT(2)) >> 2) | ((strength & BIT(0)) << 2) | (strength & BIT(1));
> + goto config;
> }
>
> if (ctrl->type == RV1126) {
> @@ -2469,6 +2652,7 @@ static int rockchip_get_pull(struct rockchip_pin_bank *bank, int pin_num)
> case RK3368:
> case RK3399:
> case RK3568:
> + case RK3576:
> case RK3588:
> pull_type = bank->pull_type[pin_num / 8];
> data >>= bit;
> @@ -2528,6 +2712,7 @@ static int rockchip_set_pull(struct rockchip_pin_bank *bank,
> case RK3368:
> case RK3399:
> case RK3568:
> + case RK3576:
> case RK3588:
> pull_type = bank->pull_type[pin_num / 8];
> ret = -EINVAL;
> @@ -2793,6 +2978,7 @@ static bool rockchip_pinconf_pull_valid(struct rockchip_pin_ctrl *ctrl,
> case RK3368:
> case RK3399:
> case RK3568:
> + case RK3576:
> case RK3588:
> return (pull != PIN_CONFIG_BIAS_PULL_PIN_DEFAULT);
> }
> @@ -3439,6 +3625,15 @@ static int rockchip_pinctrl_probe(struct platform_device *pdev)
> }
> }
>
> + /* try to find the optional reference to the sys_grf syscon */
> + node = of_parse_phandle(np, "rockchip,sys-grf", 0);
> + if (node) {
> + info->regmap_sys_grf = syscon_node_to_regmap(node);
> + of_node_put(node);
> + if (IS_ERR(info->regmap_sys_grf))
> + return PTR_ERR(info->regmap_sys_grf);
> + }
> +
not needed if the i3c stuff moves into the grf driver.
> /* try to find the optional reference to the pmu syscon */
> node = of_parse_phandle(np, "rockchip,pmu", 0);
> if (node) {
> @@ -3949,6 +4144,37 @@ static struct rockchip_pin_ctrl rk3568_pin_ctrl = {
> .schmitt_calc_reg = rk3568_calc_schmitt_reg_and_bit,
> };
>
> +#define RK3576_PIN_BANK(ID, LABEL, OFFSET0, OFFSET1, OFFSET2, OFFSET3) \
> + PIN_BANK_IOMUX_FLAGS_OFFSET_PULL_FLAGS(ID, 32, LABEL, \
> + IOMUX_WIDTH_4BIT, \
> + IOMUX_WIDTH_4BIT, \
> + IOMUX_WIDTH_4BIT, \
> + IOMUX_WIDTH_4BIT, \
> + OFFSET0, OFFSET1, \
> + OFFSET2, OFFSET3, \
> + PULL_TYPE_IO_1V8_ONLY, \
> + PULL_TYPE_IO_1V8_ONLY, \
> + PULL_TYPE_IO_1V8_ONLY, \
> + PULL_TYPE_IO_1V8_ONLY)
> +
> +static struct rockchip_pin_bank rk3576_pin_banks[] = {
> + RK3576_PIN_BANK(0, "gpio0", 0, 0x8, 0x2004, 0x200C),
> + RK3576_PIN_BANK(1, "gpio1", 0x4020, 0x4028, 0x4030, 0x4038),
> + RK3576_PIN_BANK(2, "gpio2", 0x4040, 0x4048, 0x4050, 0x4058),
> + RK3576_PIN_BANK(3, "gpio3", 0x4060, 0x4068, 0x4070, 0x4078),
> + RK3576_PIN_BANK(4, "gpio4", 0x4080, 0x4088, 0xA390, 0xB398),
> +};
> +
> +static struct rockchip_pin_ctrl rk3576_pin_ctrl __maybe_unused = {
> + .pin_banks = rk3576_pin_banks,
> + .nr_banks = ARRAY_SIZE(rk3576_pin_banks),
> + .label = "RK3576-GPIO",
> + .type = RK3576,
> + .pull_calc_reg = rk3576_calc_pull_reg_and_bit,
> + .drv_calc_reg = rk3576_calc_drv_reg_and_bit,
> + .schmitt_calc_reg = rk3576_calc_schmitt_reg_and_bit,
> +};
> +
> static struct rockchip_pin_bank rk3588_pin_banks[] = {
> RK3588_PIN_BANK_FLAGS(0, 32, "gpio0",
> IOMUX_WIDTH_4BIT, PULL_TYPE_IO_1V8_ONLY),
> @@ -4005,6 +4231,8 @@ static const struct of_device_id rockchip_pinctrl_dt_match[] = {
> .data = &rk3399_pin_ctrl },
> { .compatible = "rockchip,rk3568-pinctrl",
> .data = &rk3568_pin_ctrl },
> + { .compatible = "rockchip,rk3576-pinctrl",
> + .data = &rk3576_pin_ctrl },
> { .compatible = "rockchip,rk3588-pinctrl",
> .data = &rk3588_pin_ctrl },
> {},
> diff --git a/drivers/pinctrl/pinctrl-rockchip.h b/drivers/pinctrl/pinctrl-rockchip.h
> index 849266f8b1913..0b2b56014b173 100644
> --- a/drivers/pinctrl/pinctrl-rockchip.h
> +++ b/drivers/pinctrl/pinctrl-rockchip.h
> @@ -197,6 +197,7 @@ enum rockchip_pinctrl_type {
> RK3368,
> RK3399,
> RK3568,
> + RK3576,
> RK3588,
> };
>
> @@ -455,6 +456,7 @@ struct rockchip_pinctrl {
> int reg_size;
> struct regmap *regmap_pull;
> struct regmap *regmap_pmu;
> + struct regmap *regmap_sys_grf;
same
> struct device *dev;
> struct rockchip_pin_ctrl *ctrl;
> struct pinctrl_desc pctl;
>
The pinctrl changes for the core rk3576 parts look fine.
Heiko
More information about the Linux-rockchip
mailing list