[PATCH V2 1/2 RESEND] arm64: dts: rockchip: Add DTS for FriendlyARM NanoPi R2S Plus
Heiko Stübner
heiko at sntech.de
Wed Aug 14 04:36:43 PDT 2024
Am Mittwoch, 14. August 2024, 13:21:38 CEST schrieb Sergey 'Jin' Bostandzhyan:
> Hi,
>
> On Sat, Aug 10, 2024 at 09:11:56PM +0200, Heiko Stübner wrote:
> > Am Montag, 5. August 2024, 10:59:35 CEST schrieb Sergey 'Jin' Bostandzhyan:
> > > On Sun, Aug 04, 2024 at 01:27:50AM +0100, Daniel Golle wrote:
> > > > On Thu, Aug 01, 2024 at 05:57:35PM +0000, Sergey Bostandzhyan wrote:
> > > > > The R2S Plus is basically an R2S with additional eMMC.
> > > > >
> > > > > The eMMC configuration for the DTS has been extracted and copied from
> > > > > rk3328-nanopi-r2.dts, v2017.09 branch from the friendlyarm/uboot-rockchip
> > > > > repository.
> > > > >
> > > > > Signed-off-by: Sergey Bostandzhyan <jin at mediatomb.cc>
> > > > > ---
> > > > > arch/arm64/boot/dts/rockchip/Makefile | 1 +
> > > > > .../dts/rockchip/rk3328-nanopi-r2s-plus.dts | 31 +++++++++++++++++++
> > > > > 2 files changed, 32 insertions(+)
> > > > > create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s-plus.dts
> > > > >
> > > > > diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> > > > > index fda1b980eb4b..36258dc8dafd 100644
> > > > > --- a/arch/arm64/boot/dts/rockchip/Makefile
> > > > > +++ b/arch/arm64/boot/dts/rockchip/Makefile
> > > > > @@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
> > > > > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2c.dtb
> > > > > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2c-plus.dtb
> > > > > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s.dtb
> > > > > +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s-plus.dtb
> > > > > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-orangepi-r1-plus.dtb
> > > > > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-orangepi-r1-plus-lts.dtb
> > > > > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
> > > > > diff --git a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s-plus.dts b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s-plus.dts
> > > > > new file mode 100644
> > > > > index 000000000000..7b83090a2145
> > > > > --- /dev/null
> > > > > +++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s-plus.dts
> > > > > @@ -0,0 +1,31 @@
> > > > > +// SPDX-License-Identifier: GPL-2.0+
> > > > > +/*
> > > > > + * (C) Copyright 2018 FriendlyElec Computer Tech. Co., Ltd.
> > > > > + * (http://www.friendlyarm.com)
> > > > > + *
> > > > > + * (C) Copyright 2016 Rockchip Electronics Co., Ltd
> > > > > + */
> > > > > +
> > > > > +/dts-v1/;
> > > > > +#include "rk3328-nanopi-r2s.dts"
> > > > > +
> > > > > +/ {
> > > > > + model = "FriendlyElec NanoPi R2S Plus";
> > > > > + compatible = "friendlyarm,nanopi-r2s-plus", "rockchip,rk3328";
> > > > > +
> > > > > + aliases {
> > > > > + mmc1 = &emmc;
> > > > > + };
> > > > > +};
> > > > > +
> > > > > +&emmc {
> > > > > + bus-width = <8>;
> > > > > + cap-mmc-highspeed;
> > > > > + supports-emmc;
> > > > > + disable-wp;
> > > > > + non-removable;
> > > > > + num-slots = <1>;
> > > > > + pinctrl-names = "default";
> > > > > + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
> > > >
> > > > I think it's worth adding
> > > >
> > > > mmc-hs200-1_8v;
> > > >
> > > >
> > > > I've tried getting the best speed possible and while HS400 with and
> > > > without enhanced strobe did NOT work, hs200 works just fine.
> > > > [ 0.459863] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
> > > > [ 0.460884] mmc_host mmc1: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0)
> > > > ...
> > > > [ 0.728220] dwmmc_rockchip ff520000.mmc: Successfully tuned phase to 194
> > > > [ 0.728940] mmc1: new HS200 MMC card at address 0001
> > > > [ 0.730774] mmcblk1: mmc1:0001 A3A551 28.9 GiB
> > > > [ 0.733262] mmcblk1: p1 p2
> > > > [ 0.734562] mmcblk1boot0: mmc1:0001 A3A551 4.00 MiB
> > > > [ 0.736818] mmcblk1boot1: mmc1:0001 A3A551 4.00 MiB
> > > > [ 0.738503] mmcblk1rpmb: mmc1:0001 A3A551 16.0 MiB, chardev (245:0)
> > > >
> > > > root at OpenWrt:/# hdparm -t /dev/mmcblk1
> > > >
> > > > /dev/mmcblk1:
> > > > Timing buffered disk reads: 342 MB in 3.00 seconds = 113.81 MB/sec
> > > >
> > > >
> > > > Without 'mmc-hs200-1_8v' property in DT the eMMC is detected as
> > > > [ 0.440465] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
> > > > [ 0.442032] mmc1: new high speed MMC card at address 0001
> > > > [ 0.444261] mmcblk1: mmc1:0001 A3A551 28.9 GiB
> > > > [ 0.447388] mmcblk1: p1 p2
> > > > [ 0.448744] mmcblk1boot0: mmc1:0001 A3A551 4.00 MiB
> > > > [ 0.451065] mmcblk1boot1: mmc1:0001 A3A551 4.00 MiB
> > > > [ 0.452871] mmcblk1rpmb: mmc1:0001 A3A551 16.0 MiB, chardev (245:0)
> > > >
> > > >
> > > > root at OpenWrt:/# hdparm -t /dev/mmcblk1
> > > >
> > > > /dev/mmcblk1:
> > > > Timing buffered disk reads: 134 MB in 3.03 seconds = 44.18 MB/sec
> > > >
> > > >
> > > > > + status = "okay";
> > > > > +};
> > > >
> > > > I'm right now trying to get SDIO RTL8822CS working, so far I'm out of luck,
> > > > but it can be added later once we got it working.
> > >
> > > would you be interested in taking over my attempted patches? Thing is,
> > > that I am a userspace guy who only copy-pasted some entries from
> > > FriendlyElec and things happened to work, but I really have no clue what I am
> > > doing when it comes to hardware and DTS. I see that some changes were suggested,
> > > not only by you above, but also by others earlier and I have little
> > > understanding of where I should be inserting what and how.
> > >
> > > At this point I think it would make more sense if someone who actually
> > > understands what they are doing would continue to tune the DTS :)
> > >
> > > So it'd be great if either you or anyone else would be willing to take
> > > over?
> >
> > Though, a board devicetree is a nice way to get "your feet wet" in the
> > kernel :-) and for a lot of people scratching ones own itches gets them
> > started.
>
> While this may very well be true, my main issue is not the DT syntax,
> but the lack of understanding of the underlying hardware and also a lack of
> enthusiasm to dive into the hardware topics - I prefer to stay in
> userspace where the kernel provides a very nice abstraction to all those
> details ;)
No worries :-) .
Though in this case you're "on the hook" for the board devicetree :-D .
> > The devicetree is easy enough, also looks correct and you even got the
> > binding change correct - and you're the person with the actual board :-) .
> >
> > Could you possibly test if the mmc-hs200-1_8v; property works for you?
>
> It does, I get pretty much the same results as Daniel:
>
> root at nanopi-r2s-plus:~# hdparm -t /dev/mmcblk1
> /dev/mmcblk1:
> Timing buffered disk reads: 134 MB in 3.04 seconds = 44.13 MB/sec
>
> With mmc-hs200-1_8v:
>
> root at nanopi-r2s-plus:~# hdparm -t /dev/mmcblk1
> /dev/mmcblk1:
> Timing buffered disk reads: 340 MB in 3.01 seconds = 113.08 MB/sec
>
> Should I add a commit on top with this change and submit a v3 patchset?
>
> On Thu, Aug 01, 2024 at 11:22:27PM +0200, Heiko Stübner wrote:
> > general remark, please don't send new versions as threaded replies to
> > old
> > versions. The normal case for git-send-email is to create a new thread
> > and this continuing inside the old thread confues tooling.
>
> In case you tell me to go ahead with a v3 set, should it be in this
> thread or not? I understood RESEND's should be new, but updates should
> stay in the thread, right?
>
> Sorry, I actually did read the guides, but seems misunderstood what I should
> be doing as I inserted the in-reply-to header in my last RESEND.
Please do a v3 ... in a new thread.
Also for the process, please add the Ack you received for patch 2
in that v3.
Thanks
Heiko
More information about the Linux-rockchip
mailing list