[PATCH v2 3/4] arm64: dts: rockchip: Add base DT for rk3528 SoC

[Dragan Simic]

Hello Yao,

Please see one comment below.

On 2024-08-11 16:07, Yao Zi wrote:
> This initial device tree describes CPU, interrupts and UART on the chip
> and is able to boot into basic kernel with only UART. Cache information
> is omitted for now as there is no precise documentation. Support for
> other features will be added later.
> 
> Signed-off-by: Yao Zi <ziyao at disroot.org>
> ---
>  arch/arm64/boot/dts/rockchip/rk3528.dtsi | 182 +++++++++++++++++++++++
>  1 file changed, 182 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/rockchip/rk3528.dtsi
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3528.dtsi
> b/arch/arm64/boot/dts/rockchip/rk3528.dtsi
> new file mode 100644
> index 000000000000..0596cdc38737
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3528.dtsi
> @@ -0,0 +1,182 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2022 Rockchip Electronics Co., Ltd.
> + * Copyright (c) 2024 Yao Zi <ziyao at disroot.org>
> + */
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> +	compatible = "rockchip,rk3528";
> +
> +	interrupt-parent = <&gic>;
> +	#address-cells = <2>;
> +	#size-cells = <2>;
> +
> +	aliases {
> +		serial0 = &uart0;
> +		serial1 = &uart1;
> +		serial2 = &uart2;
> +		serial3 = &uart3;
> +		serial4 = &uart4;
> +		serial5 = &uart5;
> +		serial6 = &uart6;
> +		serial7 = &uart7;
> +	};
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu-map {
> +			cluster0 {
> +				core0 {
> +					cpu = <&cpu0>;
> +				};
> +				core1 {
> +					cpu = <&cpu1>;
> +				};
> +				core2 {
> +					cpu = <&cpu2>;
> +				};
> +				core3 {
> +					cpu = <&cpu3>;
> +				};
> +			};
> +		};
> +
> +		cpu0: cpu at 0 {
> +			compatible = "arm,cortex-a53";
> +			reg = <0x0>;
> +			device_type = "cpu";
> +			enable-method = "psci";
> +		};
> +
> +		cpu1: cpu at 1 {
> +			compatible = "arm,cortex-a53";
> +			reg = <0x1>;
> +			device_type = "cpu";
> +			enable-method = "psci";
> +		};
> +
> +		cpu2: cpu at 2 {
> +			compatible = "arm,cortex-a53";
> +			reg = <0x2>;
> +			device_type = "cpu";
> +			enable-method = "psci";
> +		};
> +
> +		cpu3: cpu at 3 {
> +			compatible = "arm,cortex-a53";
> +			reg = <0x3>;
> +			device_type = "cpu";
> +			enable-method = "psci";
> +		};
> +	};
> +
> +	psci {
> +		compatible = "arm,psci-1.0", "arm,psci-0.2";
> +		method = "smc";
> +	};
> +
> +	timer {
> +		compatible = "arm,armv8-timer";
> +		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | 
> IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> +	};
> +
> +	xin24m: clk-24m {

Please use "xin24m: clock-xin24m { ... }" instead, because that follows
the recently established revised pattern for clock names.  We should 
have
come consistency in the new SoC dtsi additions.

> +		compatible = "fixed-clock";
> +		clock-frequency = <24000000>;
> +		clock-output-names = "xin24m";
> +		#clock-cells = <0>;
> +	};