[PATCH v3 3/3] arm64: dts: rockchip: Add Orange Pi 5

[Dhruva Gole]

Hello,

On Oct 05, 2023 at 16:54:04 +0300, Muhammed Efe Cetin wrote:
> Hello,
> 
> On 28.09.2023 13:51, Dhruva Gole wrote:
> > Hi,
> > 
> > On Aug 21, 2023 at 18:47:59 +0300, Muhammed Efe Cetin wrote:
> >> Add initial support for OPi5 that includes support for USB2, PCIe2, Sata,
> >> Sdmmc, SPI Flash, PMIC.
> >>
> >> Signed-off-by: Muhammed Efe Cetin <efectn at 6tel.net>
> >> Reviewed-by: Ondřej Jirman <megi at xff.cz>
> >> ---
> >>   arch/arm64/boot/dts/rockchip/Makefile         |   1 +
> >>   .../boot/dts/rockchip/rk3588s-orangepi-5.dts  | 673 ++++++++++++++++++
> >>   2 files changed, 674 insertions(+)
> >>   create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts
> >>
> > ...
> > 
> > Can you provide some sort of documentation on how I can build and boot
> > the kernel on this board? I was unable to use the upstream arm64
> > defconfig with this exact series applied to boot the board.
> 
> What was wrong when you tried to compile & boot the board? Can you provide some logs?

Umm don't have logs at hand, but I remember it didn't really reach the
linux first line either, it went into sort of a bootloop just after
the uboot stage.

> 
> > 
> >> +
> >> +&i2c6 {
> >> +	pinctrl-names = "default";
> >> +	pinctrl-0 = <&i2c6m3_xfer>;
> >> +	status = "okay";
> >> +
> >> +	hym8563: rtc at 51 {
> >> +		compatible = "haoyu,hym8563";
> >> +		reg = <0x51>;
> >> +		#clock-cells = <0>;
> >> +		clock-output-names = "hym8563";
> >> +		pinctrl-names = "default";
> >> +		pinctrl-0 = <&hym8563_int>;
> >> +		interrupt-parent = <&gpio0>;
> >> +		interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
> >> +		wakeup-source;
> > 
> > Are you able to actually use rtc as a wakeup source? I tried this
> > on a downstream kernel that I mention below..
> > 
> > rtcwake -s 10 -m mem
> > 
> > didn't actually seem to wake the device from deepsleep after 10 seconds.
> > Do you know what other pins I can use as wakeup sources?
> 
> No, i've not tried it before.

ah okay

> 
> > 
> >> +	};
> >> +};
> >> +
> >> +&mdio1 {
> >> +	rgmii_phy1: ethernet-phy at 1 {
> >> +		compatible = "ethernet-phy-ieee802.3-c22";
> > 
> > Just wondering, can you please give some logs of the board with eth
> > working? The image that I have from opi seems to fail eth? As in I am
> > not able to see any ip address. here are the logs:
> > 
> > https://gist.github.com/DhruvaG2000/eda2762e35013c8d5ac9f37e818103a3
> 
> Unfortunately the board is not near me currently. However, i was able to use GMAC ethernet in both the upstreram and downstream kernels. Did you try any images other than Orange Pi ones?

Nope, are there any other images that maybe more suitable? Please can you point me to them?

> 
> > 
> > ...
> > 
> 

-- 
Best regards,
Dhruva Gole <d-gole at ti.com>