[PATCH 2/3] iommu/rockchip: Disable the device link during resume

[Jagan Teki]

On Thu, Mar 30, 2023 at 7:13 PM Robin Murphy <robin.murphy at arm.com> wrote:
>
> On 2023-03-30 14:17, Jagan Teki wrote:
> > Rockchip iommu is trying to enable the associated device at runtime
> > resume however some devices might enable the iommu during their pm
> > runtime resume operation which indeed leads iommu to use the wrong
> > domain and this leads to device iommu page fault.
> >
> > An example of this behavior has been observed in Rockchip RK3328, where
> > iommu stalls request timeout dring VOP device enablement.
> >
> > Here is the dmesg log for the same:
> >
> > rockchip-drm display-subsystem: bound ff370000.vop (ops vop_component_ops)
> > dwhdmi-rockchip ff3c0000.hdmi: supply avdd-0v9 not found, using dummy regulator
> > rk_iommu ff373f00.iommu: Enable stall request timed out, status: 0x00004b
> > dwhdmi-rockchip ff3c0000.hdmi: supply avdd-1v8 not found, using dummy regulator
> > rk_iommu ff373f00.iommu: Disable paging request timed out, status: 0x00004b
> > dwhdmi-rockchip ff3c0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (inno_dw_hdmi_phy2)
> > dwhdmi-rockchip ff3c0000.hdmi: registered DesignWare HDMI I2C bus driver
> > rockchip-drm display-subsystem: bound ff3c0000.hdmi (ops dw_hdmi_rockchip_ops)
> > [drm] Initialized rockchip 1.0.0 20140818 for display-subsystem on minor 0
> >
> > This issue is reproduced if we enable the display in U-Boot however
> > U-Boot is not even touched any iommu register as the U-Boot display
> > uses the simple frame buffer like other Rockchip platforms RK3399,
> > and RK3328 do.
> >
> > When VOP is trying to enable the iommu using runtime resume call
> > pm_runtime_resume_and_get from @vop_enable then the iommu runtime
> > resume call @rk_iommu_resume will try to attach the VOP in the wrong
> > domain via @rk_iommu_enable will lead to the vop iommu page fault.
>
> That sounds like a driver bug. The whole point of the device link is

Do you mean the bug in rockchip-iommu.c or vop?

> supposed to be that the IOMMU gets suspended after the VOP, and resumed
> before it, so it can make sure that whatever translations the VOP was
> using are restored *before* the VOP starts trying to access them again.
> If the IOMMU driver is failing to restore the correct state on resume,
> no amount of DT abuse is the right answer.

Then how can we handle the co-relation b/w them as VOP already
attaching the iommu and at the same time IOMMU trying to enable VOP
device but referring to the wrong domain? Any suggestions?

>
> I can understand if the IOMMU itself expects to be idle for the initial
> configuration at probe time, and gets unhappy if we try to reset it
> while (bypass) VOP traffic for the bootloader framebuffer is still going
> through, but that's an entirely different issue, and again hacking

Does it mean accessing VOP traffic at the bootloader stage effecting
iommu even though the VOP drivers in the bootloader are not using
iommu at all?

Thanks,
Jagan.