[PATCH-next v1] arm64: dts: rockchip: Enable NVM Express PCIe controller on rock3a

[Anand Moon]

Hi Chukun,

On Tue, 27 Sept 2022 at 23:45, Chukun Pan <amadeus at jmu.edu.cn> wrote:
>
> Hi Anand,
>
> On 27-09-22, 19:16, Anand Moon wrote:
>
> > As per the schematic below pice support with 2 regulators
> >
> > VCC3V3_PCIE        (SCT2250FPA)
> > VCC3V3_PI6C_03  (PI6C557-03 is a spread spectrum clock generator
> > supporting PCI Express and Ethernet requirements)
>
> > [0] https://dl.radxa.com/rock3/docs/hw/3a/rock3a_v1.3_sch.pdf
>
> Thanks for sharing, I rewrote this patch, can you try again?
>

No, It's not working on my board.
I have to enable CONFIG_REGULATOR_DEBUG, See the logs below.

[ 0.784121] reg-fixed-voltage vcc3v3-pi6c-03-regulator: vcc3v3_pi6c03
supplying 3300000uV
[ 0.784430] vcc3v3_pcie: 3300 mV, disabled

[0] https://pastebin.com/aEKQx1YZ

> > No, it did not work on my board, see bool logs.
> > [0] https://pastebin.com/Lk93VFxg
>
If you check the driver code it requires *data-line* and *num-lanes
from the dts.

[ 0.725985] phy phy-fe8c0000.phy.4: lane number 0, val 1
[ 0.726975] phy phy-fe8c0000.phy.4: rockchip_p3phy_rk3568_init: lock
failed 0x6890000, check input refclk and power supply
[ 0.728172] phy phy-fe8c0000.phy.4: phy init failed --> -110
[ 0.728704] rockchip-dw-pcie: probe of 3c0800000.pcie failed with error -110

> From the boot log, looks like ethernet is broken:
>   mdio_bus stmmac-0: MDIO device at address 0 is missing.
>   rk_gmac-dwmac fe010000.ethernet eth0: no phy at addr -1
>
> Actually I had this problem too, and reusing the "snps, reset"
> property solved it. What confuses me is am I doing something
> wrong or there is something wrong with the device tree now?
>

Yep, I have the following changes that work to bring the Ethernet up.

alarm at rock-3a:~/linux-next-5.y-devel$ git diff
arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
index 097cee13885d..498b9b2af3ed 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
@@ -242,6 +242,11 @@ &gmac1 {
        assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>;
        assigned-clock-rates = <0>, <125000000>;
        clock_in_out = "output";
+
+       snps,reset-gpio = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+       snps,reset-delays-us = <0 20000 100000>;
+       snps,reset-active-low;
+
        phy-handle = <&rgmii_phy1>;
        phy-mode = "rgmii-id";
        pinctrl-names = "default";
@@ -250,6 +255,8 @@ &gmac1m1_tx_bus2
                     &gmac1m1_rx_bus2
                     &gmac1m1_rgmii_clk
                     &gmac1m1_rgmii_bus>;
+       tx_delay = <0x30>;
+       rx_delay = <0x10>;
        status = "okay";
 };

@@ -559,14 +566,11 @@ &i2s1_8ch {
 };

 &mdio1 {
-       rgmii_phy1: ethernet-phy at 0 {
+       rgmii_phy1: ethernet-phy at 1 {
                compatible = "ethernet-phy-ieee802.3-c22";
-               reg = <0x0>;
+               reg = <0x1>;
                pinctrl-names = "default";
                pinctrl-0 = <&eth_phy_rst>;
-               reset-assert-us = <20000>;
-               reset-deassert-us = <100000>;
-               reset-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
        };
 };

Thanks
-Anand