[PATCH-next v1] arm64: dts: rockchip: Enable NVM Express PCIe controller on rock3a

[Anand Moon]

Add the nodes to enable the NVM Express PCIe controller on the
Radxa ROCK3 Model A board.

Cc: Chukun Pan <amadeus at jmu.edu.cn>
Cc: Michael Riesch <michael.riesch at wolfvision.net>
Signed-off-by: Anand Moon <linux.amoon at gmail.com>
---
alarm at rock-3a:~$ lspci
0000:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3568 Remote Signal Processor (rev 01)
0002:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3568 Remote Signal Processor (rev 01)
0002:01:00.0 Non-Volatile memory controller: Micron/Crucial Technology P2 NVMe PCIe SSD (rev 01)
---
 .../boot/dts/rockchip/rk3568-rock-3a.dts      | 36 +++++++++++++++++++
 1 file changed, 36 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
index fb87a168fe96..44d85ee1631e 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
@@ -79,6 +79,26 @@ vcc3v3_pcie: vcc3v3-pcie-regulator {
 		vin-supply = <&vcc5v0_sys>;
 	};
 
+	/* pi6c pcie clock generator feeds both ports */
+	vcc3v3_pi6c_03: vcc3v3-pi6c-03-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_pi6c_03";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <200000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	pcie30_3v3: gpio-regulator {
+		compatible = "regulator-gpio";
+		regulator-name = "pcie30_3v3";
+		regulator-min-microvolt = <100000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0x1>;
+		states = <100000 0x0>, <3300000 0x1>;
+	};
+
 	vcc3v3_sys: vcc3v3-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc3v3_sys";
@@ -546,6 +566,22 @@ &pcie2x1 {
 	status = "okay";
 };
 
+&pcie30phy {
+	data-lanes = <0 1 2 3>;
+	phy-supply = <&vcc3v3_pi6c_03>;
+	status = "okay";
+};
+
+&pcie3x2 {
+	/* mPCIe slot */
+	num-lanes = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie30x2m1_pins>;
+	reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&pcie30_3v3>;
+	status = "okay";
+};
+
 &pinctrl {
 	cam {
 		vcc_cam_en: vcc_cam_en {
-- 
2.37.3