[PATCH v2 15/16] iio: health: max30102: do not use internal iio_dev lock

[Nuno Sá]

On Sun, 2022-10-09 at 12:44 +0100, Jonathan Cameron wrote:
> On Wed, 05 Oct 2022 10:17:00 +0200
> Nuno Sá <noname.nuno at gmail.com> wrote:
> 
> > On Tue, 2022-10-04 at 17:15 +0300, Andy Shevchenko wrote:
> > > On Tue, Oct 4, 2022 at 4:49 PM Nuno Sá <nuno.sa at analog.com>
> > > wrote:  
> > > > 
> > > > The pattern used in this device does not quite fit in the
> > > > iio_device_claim_direct_mode() typical usage. In this case, we
> > > > want
> > > > to
> > > > know if we are in buffered mode or not to know if the device is
> > > > powered
> > > > (buffer mode) or not. And depending on that max30102_get_temp()
> > > > will
> > > > power on the device if needed. Hence, in order to keep the same
> > > > functionality, we try to:
> > > > 
> > > > 1. Claim Buffered mode;
> > > > 2: If 1) succeeds call max30102_get_temp() without powering on
> > > > the
> > > >    device;
> > > > 3: Release Buffered mode;
> > > > 4: If 1) fails, Claim Direct mode;
> > > > 5: If 4) succeeds call max30102_get_temp() with powering on the
> > > > device;
> > > > 6: Release Direct mode;
> > > > 7: If 4) fails, goto to 1) and try again.
> > > > 
> > > > This dance between buffered and direct mode is not particularly
> > > > pretty
> > > > (as well as the loop introduced by the goto statement) but it
> > > > does
> > > > allow
> > > > us to get rid of the mlock usage while keeping the same
> > > > behavior.  
> > > 
> > > ...
> > >   
> > > > +               if (iio_device_claim_buffer_mode(indio_dev)) { 
> > > 
> > > Why is ret not used here?
> > >   
> > > > +                       /*
> > > > +                        * This one is a *bit* hacky. If we
> > > > cannot
> > > > claim buffer
> > > > +                        * mode, then try direct mode so that
> > > > we
> > > > make sure
> > > > +                        * things cannot concurrently change.
> > > > And
> > > > we just keep
> > > > +                        * trying until we get one of the
> > > > modes...
> > > > +                        */
> > > > +                       if
> > > > (iio_device_claim_direct_mode(indio_dev))  
> > > 
> > > ...and here?
> > >   
> > > > +                               goto any_mode_retry;  
> > >   
> > > > +               } else {  
> > >   
> > > > +               }  
> > > 
> > > I.o.w. what error code will be visible to the caller and why.
> > >   
> > 
> > Note that we do not really care about the error code returned by
> > both
> > iio_device_claim_buffer_mode() and iio_device_claim_direct_mode().
> > We
> > just loop until we get one of the modes (thus ret = 0) so that we
> > can
> > safely call one of the max30102_get_temp() variants. And that will
> > be
> > the visible error code (if any). That said, you can look at the
> > first
> > version of the series about this (and the previous patch) and why
> > this
> > is being done like this (note that I'm also not 100% convinced
> > about
> > this ping pong between getting one of the IIO modes but it's also
> > not
> > that bad and if there's no major complains, I'm fine with it).
> 
> This is a vanishingly rare corner case and not in a remotely high
> performance
> path so I'm not keen on introducing a more complex API just to handle
> this corner. If we added a means to get the lock independent of mode
> we'd have an interface that is far to likely to get missused.

Totally agree. It crossed my mind to have an helper for getting the
lock but that would defeat the purpose of this patchset! Well, I'm also
fine with the code as it stands so I'll leave it for v3 and if no one
complains I guess we're good to go... 


- Nuno Sá