[PATCH 3/3] arm64: dts: rockchip: add Quartz64-A sdmmc1 node

[Peter Geis]

The sdmmc1 node on Quartz64-A supports the optional wifi module from
Pine64.
Add the sdmmc1 node and requisite sdio_pwrseq to enable wifi support on
the Quartz64-A.

Signed-off-by: Peter Geis <pgwipeout at gmail.com>
---
 .../boot/dts/rockchip/rk3566-quartz64-a.dts   | 45 +++++++++++++++++++
 1 file changed, 45 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts
index 33c2c18caaa9..1d73ac6557c5 100644
--- a/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts
@@ -91,6 +91,18 @@ simple-audio-card,codec {
 		};
 	};
 
+	sdio_pwrseq: sdio-pwrseq {
+		status = "okay";
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk817 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+		reset-gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <100>;
+		power-off-delay-us = <5000000>;
+	};
+
 	vcc12v_dcin: vcc12v_dcin {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc12v_dcin";
@@ -147,6 +159,17 @@ vcc_sys: vcc_sys {
 		regulator-max-microvolt = <4400000>;
 		vin-supply = <&vbus>;
 	};
+
+	/* sourced from vcc_sys, sdio module operates internally at 3.3v */
+	vcc_wl: vcc_wl {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_wl";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_sys>;
+	};
 };
 
 &cpu0 {
@@ -475,6 +498,12 @@ pmic_int_l: pmic-int-l {
 		};
 	};
 
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	vcc_sd {
 		vcc_sd_h: vcc-sd-h {
 			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
@@ -516,6 +545,22 @@ &sdmmc0 {
 	status = "okay";
 };
 
+&sdmmc1 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	disable-wp;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc_wl>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
 &spdif {
 	status = "okay";
 };
-- 
2.25.1