[PATCH v2 3/3] arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro
Caleb Connolly
kc at postmarketos.org
Fri Aug 5 19:10:12 PDT 2022
On 06/08/2022 00:44, Tom Fitzhenry wrote:
> This is a basic DT containing regulators and UART, intended to be a
> base that myself and others can add additional nodes in future patches.
Hi,
I was surprised to see this series, and this patch especially.
An almost ready to submit version of this patch with considerably more
functionality has been sat around for a while but unfortunately never sent [1].
Creating a minimal patch to just finally get the PinePhone pro into mainline is
not a bad idea, but as it stands I'm not fully on board with this patch.
According to the link below (and my own knowledge of PPP development) Kamil is
the original author of this patch, both Kamil and Martijn created the initial
version of the devicetree. Given that you're using their work as a base, Kamil's
authorship should be respected in the patch you submit.
Their original patch [2] contained SoBs from them and Martijn, those are both
missing below. Both of their signed-off-by tags should be added before this
patch hits the mailing list, and the same for Ondrej. The order also seems wrong
(Ondrej should be last before you).
Support for the volume keys, accelerometer, magnetometer, GPIO LEDs,
touchscreen, modem codec and audio support are all missing here, but they're
included in the patches you referenced. In their current state (see Martijn's
commit [1] or my 5.19 rebase [3]) the DT for these components has been worked on
by several people, tested by the larger user community, and are already
supported in mainline. It seems strange not to include them and just leads to a
bunch of extra busywork to add them back later. It's easy enough to drop any of
these nodes during review if they become an issue.
With that being said, I've left some feedback below, with it addressed and the
authorship/SoB situation sorted out:
Reviewed-by: Caleb Connolly <kc at postmarketos.org>
Alternatively, I'd be more than happy to review a new revision with the
aforementioned nodes re-included.
Kind Regards,
Caleb
[1]:
https://git.sr.ht/~martijnbraam/linux-unlisted/commit/01f0c90f6c4c1649f17a0ced72fc32a26d509e06
[2]:
https://gitlab.com/pine64-org/linux/-/commit/261d3b5f8ac503f97da810986d1d6422430c8531
[3]:
https://gitlab.com/pine64-org/linux/-/blob/caleb/ppp-5.19-rc5/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
>
> Tested to work: booting from eMMC, output over UART.
>
> This is derived from a combination of https://gitlab.com/pine64-org/linux
> and https://megous.com/git/linux.
>
> https://wiki.pine64.org/wiki/PinePhone_Pro
>
> Co-developed-by: Ondrej Jirman <megi at xff.cz>
> Co-developed-by: Martijn Braam <martijn at brixit.nl>
> Co-developed-by: Kamil Trzciński <ayufan at ayufan.eu>
> Signed-off-by: Tom Fitzhenry <tom at tom-fitzhenry.me.uk>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../dts/rockchip/rk3399-pinephone-pro.dts | 385 ++++++++++++++++++
> 2 files changed, 386 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index ef79a672804a1..cb42e0a15808e 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -42,6 +42,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-neo4.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-r4s.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-orangepi.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinephone-pro.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-mezzanine.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
> new file mode 100644
> index 0000000000000..f5608487ad58f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
> @@ -0,0 +1,385 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2020 Martijn Braam <martijn at brixit.nl>
> + * Copyright (c) 2021 Kamil Trzciński <ayufan at ayufan.eu>
> + */
> +
> +// PinePhone Pro datasheet: https://files.pine64.org/doc/PinePhonePro/PinephonePro-Schematic-V1.0-20211127.pdf
Use C-style comments
> +
> +/dts-v1/;
> +#include <dt-bindings/input/gpio-keys.h>
This header is unused and can be dropped.
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include "rk3399.dtsi"
> +#include "rk3399-t-opp.dtsi"
> +
> +/ {
> + model = "Pine64 PinePhonePro";
> + compatible = "pine64,pinephone-pro", "rockchip,rk3399";
> + chassis-type = "handset";
> +
> + aliases {
> + mmc0 = &sdio0;
> + mmc1 = &sdmmc;
> + mmc2 = &sdhci;
> + };
> +
> + chosen {
> + stdout-path = "serial2:115200n8";
> + };
> +
> + gpio-key-power {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwrbtn_pin>;
> +
> + power {
> + debounce-interval = <20>;
> + // Per "PMU Controler", page 4.
Comments like these aren't useful and should be dropped
> + gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
> + label = "Power";
> + linux,code = <KEY_POWER>;
> + wakeup-source;
> + };
> + };
> +
> + /* Power tree */
> + /* Root power source */
These too
> + vcc_sysin: vcc-sysin {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sysin";
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + /* Main 3.3v supply */
^^
> + vcc3v3_sys: wifi_bat: vcc3v3-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc_sysin>;
> + };
> +
> + vcca1v8_s3: vcc1v8-s3 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcca1v8_s3";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc3v3_sys>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +};
> +
> +&cpu_l0 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l1 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l2 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l3 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_b0 {
> + cpu-supply = <&vdd_cpu_b>;
> +};
> +
> +&cpu_b1 {
> + cpu-supply = <&vdd_cpu_b>;
> +};
> +
> +&emmc_phy {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + // Per "SCL clock frequency", page 30, RK818 datasheet.
Drop
> + clock-frequency = <400000>;
> + i2c-scl-rising-time-ns = <168>;
> + i2c-scl-falling-time-ns = <4>;
> + status = "okay";
> +
> + // Per "PMIC RK818-3", page 13.
Drop
> + rk818: pmic at 1c {
> + compatible = "rockchip,rk818";
> + reg = <0x1c>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <RK_PC5 IRQ_TYPE_LEVEL_LOW>;
> + #clock-cells = <1>;
> + clock-output-names = "xin32k", "rk808-clkout2";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int_l>;
> + rockchip,system-power-controller;
> + wakeup-source;
> +
> + vcc1-supply = <&vcc_sysin>;
> + vcc2-supply = <&vcc_sysin>;
> + vcc3-supply = <&vcc_sysin>;
> + vcc4-supply = <&vcc_sysin>;
> + vcc6-supply = <&vcc_sysin>;
> + vcc7-supply = <&vcc3v3_sys>;
> + vcc8-supply = <&vcc_sysin>;
> + vcc9-supply = <&vcc3v3_sys>;
> +
> + regulators {
> + vdd_cpu_l: DCDC_REG1 {
> + regulator-name = "vdd_cpu_l";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_center: DCDC_REG2 {
> + regulator-name = "vdd_center";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-name = "vcc_ddr";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_1v8: vcc_wl: DCDC_REG4 {
> + regulator-name = "vcc_1v8";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + // Audio codec.
Drop
> + vcca3v0_codec: LDO_REG1 {
> + regulator-name = "vcca3v0_codec";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + // Touch screen.
Drop
> + vcc3v0_touch: LDO_REG2 {
> + regulator-name = "vcc3v0_touch";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcca1v8_codec: LDO_REG3 {
> + regulator-name = "vcca1v8_codec";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_power_on: LDO_REG4 {
> + regulator-name = "vcc_power_on";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_3v0: LDO_REG5 {
> + regulator-name = "vcc_3v0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_1v5: LDO_REG6 {
> + regulator-name = "vcc_1v5";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc1v8_dvp: LDO_REG7 {
> + regulator-name = "vcc1v8_dvp";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + vcc3v3_s3: LDO_REG8 {
> + regulator-name = "vcc3v3_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vccio_sd: LDO_REG9 {
> + regulator-name = "vccio_sd";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + vcc3v3_s0: SWITCH_REG {
> + regulator-name = "vcc3v3_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> + };
> + };
> +
> + vdd_cpu_b: regulator at 40 {
> + compatible = "silergy,syr827";
> + reg = <0x40>;
> + fcs,suspend-voltage-selector = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vsel1_pin>;
> + regulator-name = "vdd_cpu_b";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <1000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu: regulator at 41 {
> + compatible = "silergy,syr828";
> + reg = <0x41>;
> + fcs,suspend-voltage-selector = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vsel2_pin>;
> + regulator-name = "vdd_gpu";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <1000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +};
> +
> +&io_domains {
> + status = "okay";
> +
> + bt656-supply = <&vcc1v8_dvp>;
> + audio-supply = <&vcca1v8_codec>;
> + sdmmc-supply = <&vccio_sd>;
> + gpio1830-supply = <&vcc_3v0>;
> +};
> +
> +&pmu_io_domains {
> + pmu1830-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> +
> +&pinctrl {
> + buttons {
> + pwrbtn_pin: pwrbtn-pin {
> + rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + pmic {
> + pmic_int_l: pmic-int-l {
> + rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + vsel1_pin: vsel1-pin {
> + rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> +
> + vsel2_pin: vsel2-pin {
> + rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +};
> +
> +// Per "SDMMC Controler", page 6.
Drop
> +&sdmmc {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
> + disable-wp;
> + max-frequency = <150000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
> + vmmc-supply = <&vcc3v3_sys>;
> + vqmmc-supply = <&vccio_sd>;
> + status = "okay";
> +};
> +
> +&sdhci {
> + bus-width = <8>;
> + mmc-hs200-1_8v;
> + non-removable;
> + status = "okay";
> +};
> +
> +// Enable thermal sensors.
Drop
> +&tsadc {
> + /* tshut mode 0:CRU 1:GPIO */
Drop
> + rockchip,hw-tshut-mode = <1>;
> + /* tshut polarity 0:LOW 1:HIGH */
Drop
> + rockchip,hw-tshut-polarity = <1>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
More information about the Linux-rockchip
mailing list