[PATCH v2 5/8] arm64: dts: rockchip: add rk3568 tsadc nodes

[Heiko Stübner]

Hi Peter, Kever,

Am Mittwoch, 28. Juli 2021, 20:00:31 CEST schrieb Peter Geis:
> Add the thermal and tsadc nodes to the rk3568 device tree.
> There are two sensors, one for the cpu, one for the gpu.
> 
> Signed-off-by: Peter Geis <pgwipeout at gmail.com>
> ---
>  .../boot/dts/rockchip/rk3568-pinctrl.dtsi     |  7 ++
>  arch/arm64/boot/dts/rockchip/rk356x.dtsi      | 70 +++++++++++++++++++
>  2 files changed, 77 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi b/arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi
> index a588ca95ace2..3b1efaf2646e 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi
> @@ -2420,6 +2420,13 @@ spi3m1_cs1: spi3m1-cs1 {
>  	};
>  
>  	tsadc {
> +		/omit-if-no-ref/
> +		tsadc_pin: tsadc-pin {
> +			rockchip,pins =
> +				/* tsadc_pin */
> +				<0 RK_PA1 0 &pcfg_pull_none>;
> +		};
> +

The rk3568-pinctrl.dtsi is autogenerated on Rockchip's side and I don't
want to break that unnecessarily ;-) .

So the question below is more for Kever and Liang:

The tsadc on most mainline Rockchip socs uses the additional init-pinctrl
to set the pin to gpio mode before the tsadc probes and only to the shutdown
function after the tsadc has probed sucessfully. This prevents the
shutdown firing before the tsadc actually attached to the pin function.

Is it possible to fit the above addition pin setting in the database you
have as base for the autogeneration?


Thanks
Heiko





>  		/omit-if-no-ref/
>  		tsadcm0_shut: tsadcm0-shut {
>  			rockchip,pins =
> diff --git a/arch/arm64/boot/dts/rockchip/rk356x.dtsi b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> index fbd9f1c366ff..c74072941da1 100644
> --- a/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> @@ -50,6 +50,7 @@ cpu0: cpu at 0 {
>  			compatible = "arm,cortex-a55";
>  			reg = <0x0 0x0>;
>  			clocks = <&scmi_clk 0>;
> +			#cooling-cells = <2>;
>  			enable-method = "psci";
>  			operating-points-v2 = <&cpu0_opp_table>;
>  		};
> @@ -58,6 +59,7 @@ cpu1: cpu at 100 {
>  			device_type = "cpu";
>  			compatible = "arm,cortex-a55";
>  			reg = <0x0 0x100>;
> +			#cooling-cells = <2>;
>  			enable-method = "psci";
>  			operating-points-v2 = <&cpu0_opp_table>;
>  		};
> @@ -66,6 +68,7 @@ cpu2: cpu at 200 {
>  			device_type = "cpu";
>  			compatible = "arm,cortex-a55";
>  			reg = <0x0 0x200>;
> +			#cooling-cells = <2>;
>  			enable-method = "psci";
>  			operating-points-v2 = <&cpu0_opp_table>;
>  		};
> @@ -74,6 +77,7 @@ cpu3: cpu at 300 {
>  			device_type = "cpu";
>  			compatible = "arm,cortex-a55";
>  			reg = <0x0 0x300>;
> +			#cooling-cells = <2>;
>  			enable-method = "psci";
>  			operating-points-v2 = <&cpu0_opp_table>;
>  		};
> @@ -773,6 +777,72 @@ uart9: serial at fe6d0000 {
>  		status = "disabled";
>  	};
>  
> +	thermal_zones: thermal-zones {
> +		cpu_thermal: cpu-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsadc 0>;
> +
> +			trips {
> +				cpu_alert0: cpu_alert0 {
> +					temperature = <70000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +				cpu_alert1: cpu_alert1 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +				cpu_crit: cpu_crit {
> +					temperature = <95000>;
> +					hysteresis = <2000>;
> +					type = "critical";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map0 {
> +					trip = <&cpu_alert0>;
> +					cooling-device =
> +						<&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		gpu_thermal: gpu-thermal {
> +			polling-delay-passive = <20>; /* milliseconds */
> +			polling-delay = <1000>; /* milliseconds */
> +
> +			thermal-sensors = <&tsadc 1>;
> +		};
> +	};
> +
> +	tsadc: tsadc at fe710000 {
> +		compatible = "rockchip,rk3568-tsadc";
> +		reg = <0x0 0xfe710000 0x0 0x100>;
> +		interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
> +		assigned-clocks = <&cru CLK_TSADC_TSEN>, <&cru CLK_TSADC>;
> +		assigned-clock-rates = <17000000>, <700000>;
> +		clocks = <&cru CLK_TSADC>, <&cru PCLK_TSADC>;
> +		clock-names = "tsadc", "apb_pclk";
> +		resets = <&cru SRST_TSADC>, <&cru SRST_P_TSADC>,
> +			 <&cru SRST_TSADCPHY>;
> +		reset-names = "tsadc", "tsadc-apb", "tsadc-phy";
> +		rockchip,grf = <&grf>;
> +		rockchip,hw-tshut-temp = <95000>;
> +		pinctrl-names = "init", "default", "sleep";
> +		pinctrl-0 = <&tsadc_pin>;
> +		pinctrl-1 = <&tsadc_shutorg>;
> +		pinctrl-2 = <&tsadc_pin>;
> +		#thermal-sensor-cells = <1>;
> +		status = "disabled";
> +	};
> +
>  	saradc: saradc at fe720000 {
>  		compatible = "rockchip,rk3568-saradc", "rockchip,rk3399-saradc";
>  		reg = <0x0 0xfe720000 0x0 0x100>;
>