[PATCH 3/3] arm64: dts: rockchip: rk3328: Add Radxa ROCK Pi E
Chen-Yu Tsai
wens at kernel.org
Sun Jan 10 10:37:15 EST 2021
Hi,
On Sun, Jan 10, 2021 at 10:45 PM Johan Jonker <jbx6244 at gmail.com> wrote:
>
> Hi Chen-Yu,
>
> Some comments, have a look if it is useful...
>
> On 1/10/21 4:58 AM, Chen-Yu Tsai wrote:
> > From: Chen-Yu Tsai <wens at csie.org>
> >
> > Radxa ROCK Pi E is a router oriented SBC based on Rockchip's RK3328 SoC.
> > As the official wiki page puts it, "E for Ethernets".
> >
> > It features the RK3328 SoC, gigabit and fast Ethernet RJ45 ports, both
> > directly served by Ethernet controllers in the SoC, a USB 3.0 host port,
> > a power-only USB type-C port, a 3.5mm headphone jack for audio output,
>
> > two LEDs, a 40-pin Raspberry Pi style GPIO header, and optional WiFi+BT
> > and PoE header.
> >
> > The board comes in multiple configurations, differing in the amount of
> > onboard RAM, the level of WiFi+BT (none, 802.11n 2.4GHz, or 802.11ac
> > 2.4 GHz & 5 GHz), and whether PoE is supported or not. These variants
> > can all share the same device tree.
> >
> > The USB 2.0 OTG controller is available on the 40-pin header. This is
> > not enabled in the device tree, since it is possible to use it in a
> > host-only configuration, or in OTG mode with an extra pin from the
> > header as the ID pin.
> >
> > The device tree is based on the one of the Rock64, with various parts
> > modified to match the ROCK Pi E, and some parts updated to newer styles,
> > such as the gmac2io node's mdio sub-node.
> >
> > Add a new device tree file for the new board.
> >
> > Signed-off-by: Chen-Yu Tsai <wens at csie.org>
> > ---
> > arch/arm64/boot/dts/rockchip/Makefile | 1 +
> > .../boot/dts/rockchip/rk3328-rock-pi-e.dts | 369 ++++++++++++++++++
> > 2 files changed, 370 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
> >
> > diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> > index 622d320ddd13..62d3abc17a24 100644
> > --- a/arch/arm64/boot/dts/rockchip/Makefile
> > +++ b/arch/arm64/boot/dts/rockchip/Makefile
> > @@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
> > +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock-pi-e.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
> > diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
> > new file mode 100644
> > index 000000000000..7818d2e8180c
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
> > @@ -0,0 +1,369 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * (C) Copyright 2020 Chen-Yu Tsai <wens at csie.org>
> > + *
> > + * Based on ./rk3328-rock64.dts, which is
> > + *
> > + * Copyright (c) 2017 PINE64
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include <dt-bindings/leds/common.h>
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/pinctrl/rockchip.h>
> > +#include "rk3328.dtsi"
> > +
> > +/ {
> > + model = "Radxa ROCK Pi E";
> > + compatible = "radxa,rockpi-e", "rockchip,rk3328";
> > +
> > + chosen {
> > + stdout-path = "serial2:1500000n8";
> > + };
> > +
> > + gmac_clkin: external-gmac-clock {
> > + compatible = "fixed-clock";
> > + clock-frequency = <125000000>;
> > + clock-output-names = "gmac_clkin";
> > + #clock-cells = <0>;
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > + pinctrl-0 = <&led_pin>;
> > + pinctrl-names = "default";
> > +
> > + led-0 {
>
> > + /* schematic say green but the actual thing is blue */
>
> In rockpie-v1.2-20200427-sch.pdf this led is already called "LED_BLUE",
> so comment maybe not needed anymore?
Thanks. Did not notice there was a new revision.
> > + color = <LED_COLOR_ID_BLUE>;
> > + gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>;
> > + linux,default-trigger = "heartbeat";
> > + };> + };
> > +
> > + vcc_sd: sdmmc-regulator {
> > + compatible = "regulator-fixed";
> > + gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&sdmmc0m1_pin>;
>
> > + regulator-boot-on;
> > + regulator-name = "vcc_sd";
>
> regulator-name above other regulator properties
That is actually what I was used to, but some other rockchip dts files
have all the properties sorted alphabetically. So I stuck with what I
saw.
> regulator voltage missing
> make things as complete as possible
>
> from fixed-regulator.yaml:
>
> description:
> Any property defined as part of the core regulator binding, defined in
> regulator.yaml, can also be used. However a fixed voltage regulator is
> expected to have the regulator-min-microvolt and regulator-max-microvolt
> to be the same.
However this is not a real regulator; it is merely an on/off switch.
I believe in this case it should just pass through the voltage from
its upstream.
> > + vin-supply = <&vcc_io>;
> > + };
> > +
>
> > + vcc_host_5v: vcc-host-5v-regulator {
> > + compatible = "regulator-fixed";
> > + gpio = <&gpio3 RK_PA7 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&usb30_host_drv>;
> > + enable-active-high;
> > + regulator-name = "vcc_host_5v";
>
> idem limits
Same here.
> > + regulator-always-on;
> > + regulator-boot-on;
> > + vin-supply = <&vcc_sys>;
> > + };
>
> For Heiko: ?? remove ??
> usb3 has no support in mainline.
> Regulators not in use are disabled.
> For mainline this node has no use....
As it already has a defined binding, we can put it in the device tree.
> > +
> > + vcc_sys: vcc-sys {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc_sys";
>
> > + regulator-always-on;
> > + regulator-boot-on;
>
> At the other regulators this is sort below the regulator limits.
Again, alphabetically sorted vs preferred sorting method.
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + };
> > +
> > + vcc_wifi: vcc-wifi-regulator {
> > + compatible = "regulator-fixed";
> > + gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&wifi_en>;
> > + regulator-name = "vcc_wifi";
>
> idem limits
Again, it is just a switch.
> > + regulator-always-on;
> > + regulator-boot-on;
> > + vin-supply = <&vcc_io>;
> > + };
> > +};
> > +
> > +&analog_sound {
> > + status = "okay";
> > +};
> > +
> > +&codec {
> > + status = "okay";
> > +};
> > +
> > +&cpu0 {
> > + cpu-supply = <&vdd_arm>;
> > +};
> > +
> > +&cpu1 {
> > + cpu-supply = <&vdd_arm>;
> > +};
> > +
> > +&cpu2 {
> > + cpu-supply = <&vdd_arm>;
> > +};
> > +
> > +&cpu3 {
> > + cpu-supply = <&vdd_arm>;
> > +};
> > +
> > +&emmc {
> > + bus-width = <8>;
> > + cap-mmc-highspeed;
>
> > + max-frequency = <150000000>;
>
> remove
> already defined in dtsi
OK.
> > + mmc-ddr-1_8v;
> > + mmc-hs200-1_8v;
> > + non-removable;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_bus8>;
> > + vmmc-supply = <&vcc_io>;
> > + vqmmc-supply = <&vcc18_emmc>;
> > + status = "okay";
> > +};
>
> ////////////////////////
> emmc: mmc at ff520000 {
> compatible = "rockchip,rk3328-dw-mshc", "rockchip,rk3288-dw-mshc";
> reg = <0x0 0xff520000 0x0 0x4000>;
> interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
> <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
> clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
> fifo-depth = <0x100>;
> max-frequency = <150000000>;
> status = "disabled";
> };
> ////////////////////////
>
> > +
> > +&gmac2io {
> > + assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
> > + assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>;
> > + clock_in_out = "input";
> > + phy-handle = <&rtl8211e>;
> > + phy-mode = "rgmii";
> > + phy-supply = <&vcc_io>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&rgmiim1_pins>;
> > + snps,aal;
> > + snps,rxpbl = <0x4>;
> > + snps,txpbl = <0x4>;
> > + tx_delay = <0x26>;
> > + rx_delay = <0x11>;
> > + status = "okay";
> > +
> > + mdio {
> > + compatible = "snps,dwmac-mdio";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + rtl8211e: ethernet-phy at 1 {
> > + reg = <1>;
> > + pinctrl-0 = <ð_phy_int_pin>, <ð_phy_reset_pin>;
> > + pinctrl-names = "default";
> > + interrupt-parent = <&gpio1>;
> > + interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
> > + reset-assert-us = <10000>;
> > + reset-deassert-us = <50000>;
> > + reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
> > + };
> > + };
> > +};
> > +
> > +&gmac2phy {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&fephyled_linkm1>, <&fephyled_rxm1>;
> > + status = "okay";
> > +};
> > +
> > +&i2c1 {
> > + status = "okay";
> > +
> > + rk805: pmic at 18 {
> > + compatible = "rockchip,rk805";
> > + reg = <0x18>;
> > + interrupt-parent = <&gpio2>;
> > + interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
>
> > + #clock-cells = <1>;
>
> all thing that start with "#" down the list
Is there a proper "preferred" sorting method defined somewhere?
> > + clock-output-names = "xin32k", "rk805-clkout2";
> > + gpio-controller;
>
> > + #gpio-cells = <2>;
>
> idem
>
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pmic_int_l>;
> > + rockchip,system-power-controller;
> > + wakeup-source;
> > +
> > + vcc1-supply = <&vcc_sys>;
> > + vcc2-supply = <&vcc_sys>;
> > + vcc3-supply = <&vcc_sys>;
> > + vcc4-supply = <&vcc_sys>;
> > + vcc5-supply = <&vcc_io>;
> > + vcc6-supply = <&vcc_sys>;
> > +
> > + regulators {
> > + vdd_log: DCDC_REG1 {
> > + regulator-name = "vdd_log";
> > + regulator-min-microvolt = <712500>;
> > + regulator-max-microvolt = <1450000>;
> > + regulator-ramp-delay = <12500>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > +
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <1000000>;
> > + };
> > + };
> > +
> > + vdd_arm: DCDC_REG2 {
> > + regulator-name = "vdd_arm";
> > + regulator-min-microvolt = <712500>;
> > + regulator-max-microvolt = <1450000>;
> > + regulator-ramp-delay = <12500>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > +
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <950000>;
> > + };
> > + };
> > +
> > + vcc_ddr: DCDC_REG3 {
> > + regulator-name = "vcc_ddr";
> > + regulator-always-on;
> > + regulator-boot-on;
> > +
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + };
> > + };
> > +
> > + vcc_io: DCDC_REG4 {
> > + regulator-name = "vcc_io";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > +
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <3300000>;
> > + };
> > + };
> > +
> > + vcc_18: LDO_REG1 {
> > + regulator-name = "vcc_18";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > +
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <1800000>;
> > + };
> > + };
> > +
> > + vcc18_emmc: LDO_REG2 {
> > + regulator-name = "vcc18_emmc";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > +
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <1800000>;
> > + };
> > + };
> > +
> > + vdd_10: LDO_REG3 {
> > + regulator-name = "vdd_10";
> > + regulator-min-microvolt = <1000000>;
> > + regulator-max-microvolt = <1000000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > +
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <1000000>;
> > + };
> > + };
> > + };
> > + };
> > +};
> > +
> > +&i2s1 {
> > + status = "okay";
> > +};
> > +
> > +&io_domains {
> > + pmuio-supply = <&vcc_io>;
> > + vccio1-supply = <&vcc_io>;
> > + vccio2-supply = <&vcc18_emmc>;
> > + vccio3-supply = <&vcc_io>;
> > + vccio4-supply = <&vcc_io>;
> > + vccio5-supply = <&vcc_io>;
> > + vccio6-supply = <&vcc_io>;
> > + status = "okay";
> > +};
> > +
> > +&pinctrl {
>
> > + ethernet-phy {
>
> gmac2io
OK.
> phy / ethernet-phy is a reserved node name
> use something else
>
> make ARCH=arm64 dtbs_check
>
> /arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dt.yaml: ethernet-phy:
> 'reg' is a required property
> From schema: Documentation/devicetree/bindings/net/ethernet-phy.yaml
That's somewhat annoying. :(
I wouldn't say the name is "reserved", just that the binding checking
mechanism can't account for these situations.
> > + eth_phy_int_pin: eth-phy-int-pin {
> > + rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_down>;
> > + };
> > +
> > + eth_phy_reset_pin: eth-phy-reset-pin {
> > + rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
> > + };
> > + };
> > +
> > + leds {
> > + led_pin: led-pin {
> > + rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
> > + };
> > + };
> > +
> > + pmic {
> > + pmic_int_l: pmic-int-l {
> > + rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
> > + };
> > + };
> > +
>
> > + usb3 {
>
> usb
>
> Last numbers in nodenames are more related to the sort order then to
> capabillity.
> ie: mmc0, mmc1
> All usb pin related things here.
I'd say it is more related to functionality in this case, as in "this group
is for USB3 related pins". Makes more sense if the board supported both USB2
and USB3.
> > + usb30_host_drv: usb30-host-drv {
> > + rockchip,pins = <3 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>;
> > + };
> > + };
> > +
> > + wifi {
> > + wifi_en: wifi-en {
> > + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
> > + };
> > + };
> > +};
> > +
> > +&sdmmc {
> > + bus-width = <4>;
>
> > + cap-mmc-highspeed;
>
> remove
> micro SD only
>
> > + cap-sd-highspeed;
> > + disable-wp;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&sdmmc0_clk>, <&sdmmc0_cmd>, <&sdmmc0_dectn>, <&sdmmc0_bus4>;
> > + vmmc-supply = <&vcc_sd>;
> > + status = "okay";
> > +};
> > +
>
> > +&saradc {
> > + vref-supply = <&vcc_18>;
> > + status = "okay";
> > +};
>
> What happened to the recovery key from the schematic?
I believe I originally planned on adding it, but failed to find a proper
key event for it. Any suggestions?
AFAIK only U-boot handles the recovery button, but in its case it just
looks for the saradc and reads from a predefined channel.
Regards
ChenYu
> > +
> > +&tsadc {
> > + status = "okay";
> > +};
> > +
> > +&u2phy {
> > + status = "okay";
> > +};
> > +
> > +&u2phy_host {
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + status = "okay";
> > +};
> > +
> > +&usb_host0_ehci {
> > + status = "okay";
> > +};
> >
>
More information about the Linux-rockchip
mailing list