[PATCH v3 1/4] dt-bindings: Add Rockchip rk817 battery charger support

[Rob Herring]

On Mon, Aug 09, 2021 at 09:54:33PM -0500, Chris Morgan wrote:
> From: Chris Morgan <macromorgan at hotmail.com>
> 
> Create dt-binding documentation to document rk817 battery and charger
> usage. New device-tree properties have been added.
> 
> - rockchip,resistor-sense-micro-ohms: The value in microohms of the
> 				      sample resistor.
> - rockchip,sleep-enter-current-microamp: The value in microamps of the
> 					 sleep enter current.
> - rockchip,sleep-filter-current: The value in microamps of the sleep
> 				 filter current.
> 
> Signed-off-by: Chris Morgan <macromorgan at hotmail.com>
> Signed-off-by: Maya Matuszczyk <maccraft123mc at gmail.com>
> ---
>  .../devicetree/bindings/mfd/rk808.txt         | 36 ++++++++++++++++++-
>  1 file changed, 35 insertions(+), 1 deletion(-)

Kind of a big change without converting this binding to DT schema first. 

> 
> diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt
> index 23a17a6663ec..89b9fa7e10b5 100644
> --- a/Documentation/devicetree/bindings/mfd/rk808.txt
> +++ b/Documentation/devicetree/bindings/mfd/rk808.txt
> @@ -70,13 +70,40 @@ Optional RK817 properties:
>  
>  - vcc8-supply:  The input supply for BOOST
>  - vcc9-supply:  The input supply for OTG_SWITCH
> +
>  - codec:	The child node for the codec to hold additional properties.
>  		If no additional properties are required for the codec, this
>  		node can be omitted.
> -

Unrelated whitespace changes.

>  - rockchip,mic-in-differential: Telling if the microphone uses differential
>  				mode. Should be under the codec child node.
>  
> +- battery:	The child node for the charger to hold additional properties.
> +		If a battery is not in use, this node can be omitted. If a
> +		battery node is used, the following values are required:
> +		rockchip,resistor-sense, rockchip,sleep-enter-current,
> +		rockchip,sleep-filter-current, and a phandle to a

Property names are out of date...

> +		monitored-battery node that contains a valid value for
> +		charge-full-design-microamp-hours,
> +		charge-term-current-microamp,
> +		constant-charge-current-max-microamp,
> +		constant-charge-voltage-max-microvolt,
> +		voltage-max-design-microvolt, voltage-min-design-microvolt,
> +		and a valid ocv-capacity table.

Please list these 1 per line and make it clearer this is the list of 
properties for the battery node.

> +- rockchip,resistor-sense-micro-ohms: Value in microohms of the battery sense
> +				      resistor. The PMIC only supports values
> +				      of either 10000 or 20000. This value is
> +				      used by the driver to set the correct
> +				      divisor value to translate ADC readings
> +				      into the proper units of measure.
> +- rockchip,sleep-enter-current-microamp: Value in microamps of the sleep enter
> +					 current for the charger. Value is used
> +					 by the driver to calibrate the relax
> +					 threshold.
> +- rockchip,sleep-filter-current-microamp: Value in microamps of the sleep
> +					  filter current for the charger.
> +					  Value is used by the driver to derive
> +					  the sleep sample current.
> +
>  Optional RK818 properties:
>  - vcc1-supply:  The input supply for DCDC_REG1
>  - vcc2-supply:  The input supply for DCDC_REG2
> @@ -459,6 +486,13 @@ Example:
>  			};
>  		};
>  
> +		rk817_battery: battery {
> +			monitored-battery = <&battery_cell>;
> +			rockchip,resistor-sense-micro-ohms = <10000>;
> +			rockchip,sleep-enter-current-microamp = <300000>;
> +			rockchip,sleep-filter-current-microamp = <100000>;
> +		};
> +
>  		rk817_codec: codec {
>  			rockchip,mic-in-differential;
>  		};
> -- 
> 2.25.1
> 
>