[PATCH v3 2/2] arm64: dts: rockchip: Add basic support for Kobol's Helios64
Johan Jonker
jbx6244 at gmail.com
Tue Oct 13 13:34:54 EDT 2020
Hi Uwe,
Part 1 of 2 missing here.
Submit all patches to all maintainers and mail lists.
Don't forget robh+dt !
./scripts/get_maintainer.pl --noroles --norolestats --nogit-fallback
--nogit <patch 1> <patch2>
git send-email --suppress-cc all --annotate --to <..> --cc <..> <patch
1> <patch2>
On 10/13/20 6:13 PM, Uwe Kleine-König wrote:
> The hardware is described in detail on Kobol's wiki at
> https://wiki.kobol.io/helios64/intro/.
>
> Up to now the following peripherals are working:
>
> - UART
> - Micro-SD card
> - eMMC
> - ethernet port 1
> - status LED
> - temperature sensor on i2c bus 2
>
> Signed-off-by: Uwe Kleine-König <uwe at kleine-koenig.org>
> ---
Add a little change log here.
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../dts/rockchip/rk3399-kobol-helios64.dts | 378 ++++++++++++++++++
> 2 files changed, 379 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index b87b1f773083..ddf07c5e5f7c 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -24,6 +24,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-hugsun-x99.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-khadas-edge.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-khadas-edge-captain.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-khadas-edge-v.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-kobol-helios64.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-leez-p710.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopc-t4.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-m4.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts b/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts
> new file mode 100644
> index 000000000000..98a2bbed8c14
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts
> @@ -0,0 +1,378 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2020 Aditya Prayoga <aditya at kobol.io>
> + */
> +
> +/*
> + * The Kobol Helios64 is a board designed to operate as a NAS and optionally
> + * ships with an enclosing that can host five 2.5" hard disks.
> + *
> + * See https://wiki.kobol.io/helios64/intro/ for further details.
> + */
> +
> +/dts-v1/;
> +#include "rk3399.dtsi"
> +#include "rk3399-opp.dtsi"
> +
> +/ {
> + model = "Kobol Helios64";
> + compatible = "kobol,helios64", "rockchip,rk3399";
> +
> + avdd_1v8_s0: avdd-1v8-s0 {
> + compatible = "regulator-fixed";
> + regulator-name = "avdd_1v8_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc3v3_sys_s3>;
> + };
> +
> + clkin_gmac: external-gmac-clock {
> + compatible = "fixed-clock";
> + clock-frequency = <125000000>;
> + clock-output-names = "clkin_gmac";
> + #clock-cells = <0>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&fault_led &status_led>;
sort
> +
> + fault-led {
fault_led: led-0 {}
My fault.
Change ones more...
# The first form is preferred, but fall back to just 'led' anywhere in the
# node name to at least catch some child nodes.
"(^led-[0-9a-f]$|led)":
> + label = "helios64:red:fault";
> + gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>;
> + default-state = "keep";
> + };
> +
> + status-led {
status_led: led-1 {}
> + label = "helios64:green:status";
> + gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "none";
Don't use 'none' for mainline.
> + default-state = "on";
> + };
> + };
> +
> + vcc1v8_sys_s0: vcc1v8-sys-s0 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc1v8_sys_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc1v8_sys_s3>;
> + };
> +
> + vcc3v0_sd: vcc3v0-sd {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v0_sd";
Doesn't a sd card need a on/off gpio?
Could you check the schematics?
> + regulator-boot-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + vin-supply = <&vcc3v3_sys_s3>;
> + };
> +
> + vcc3v3_sys_s3: vcc_lan: vcc3v3-sys-s3 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3_sys_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc5v0_sys>;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc5v0_sys: vcc5v0-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc12v_dcin_bkup>;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc12v_dcin: vcc12v-dcin {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc12v_dcin";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + };
> +
> + vcc12v_dcin_bkup: vcc12v-dcin-bkup {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc12v_dcin_bkup";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + vin-supply = <&vcc12v_dcin>;
> + };
> +};
> +
> +/*
> + * The system doesn't run stable with cpu freq enabled, so disallow the lower
> + * frequencies until this problem is properly understood and resolved.
> + */
> +&cluster0_opp {
> + /delete-node/ opp00;
> + /delete-node/ opp01;
> + /delete-node/ opp02;
> + /delete-node/ opp03;
> + /delete-node/ opp04;
> +};
> +&cluster1_opp {
> + /delete-node/ opp00;
> + /delete-node/ opp01;
> + /delete-node/ opp02;
> + /delete-node/ opp03;
> + /delete-node/ opp04;
> + /delete-node/ opp05;
> + /delete-node/ opp06;
> +};
> +
> +&cpu_b0 {
> + cpu-supply = <&vdd_cpu_b>;
> +};
> +
> +&cpu_b1 {
> + cpu-supply = <&vdd_cpu_b>;
> +};
> +
> +&cpu_l0 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l1 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l2 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l3 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&emmc_phy {
> + status = "okay";
> +};
> +
> +&gmac {
> + assigned-clock-parents = <&clkin_gmac>;
> + assigned-clocks = <&cru SCLK_RMII_SRC>;
> + clock_in_out = "input";
> + phy-mode = "rgmii";
> + phy-supply = <&vcc_lan>;
> + pinctrl-0 = <&rgmii_pins &rgmii_phy_reset>;
> + pinctrl-names = "default";
> + rx_delay = <0x20>;
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 10000 50000>;
> + snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
> + tx_delay = <0x28>;
> + status = "okay";
> +};
> +
> +&i2c0 {
> + clock-frequency = <400000>;
> + i2c-scl-falling-time-ns = <4>;
> + i2c-scl-rising-time-ns = <168>;
> + status = "okay";
> +
> + rk808: pmic at 1b {
> + compatible = "rockchip,rk808";
> + reg = <0x1b>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
> + clock-output-names = "xin32k", "rk808-clkout2";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int_l>;
sort
> + vcc1-supply = <&vcc5v0_sys>;
> + vcc2-supply = <&vcc5v0_sys>;
> + vcc3-supply = <&vcc5v0_sys>;
> + vcc4-supply = <&vcc5v0_sys>;
> + vcc6-supply = <&vcc5v0_sys>;
> + vcc7-supply = <&vcc5v0_sys>;
> + vcc8-supply = <&vcc3v3_sys_s3>;
> + vcc9-supply = <&vcc5v0_sys>;
> + vcc10-supply = <&vcc5v0_sys>;
> + vcc11-supply = <&vcc5v0_sys>;
> + vcc12-supply = <&vcc3v3_sys_s3>;
> + vddio-supply = <&vcc3v0_s3>;
> + wakeup-source;
> +
remove empty line
> + #clock-cells = <1>;
> +
> + regulators {
> + vdd_cpu_l: DCDC_REG2 {
> + regulator-name = "vdd_cpu_l";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <1350000>;
> + regulator-min-microvolt = <750000>;
The rest has min above max.
Exception to the sort rule, not sure what Heiko wants, but keep it every
where the same.
> + regulator-ramp-delay = <6001>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc1v8_sys_s3: DCDC_REG4 {
> + regulator-name = "vcc1v8_sys_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <1800000>;
> + regulator-min-microvolt = <1800000>;
idem
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc_sdio_s0: LDO_REG4 {
> + regulator-name = "vcc_sdio_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3000000>;
keep
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3000000>;
> + };
> + };
> +
> + vcc3v0_s3: LDO_REG8 {
> + regulator-name = "vcc3v0_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <3000000>;
> + regulator-min-microvolt = <3000000>;
change
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3000000>;
> + };
> + };
> + };
> + };
> +
> + vdd_cpu_b: regulator at 40 {
> + compatible = "silergy,syr827";
> + reg = <0x40>;
> + fcs,suspend-voltage-selector = <1>;
> + pinctrl-0 = <&vsel1_gpio>;
> + pinctrl-names = "default";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <1500000>;
> + regulator-min-microvolt = <712500>;
change
> + regulator-name = "vdd_cpu_b";
> + regulator-ramp-delay = <1000>;
> + vin-supply = <&vcc5v0_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +};
> +
> +&i2c2 {
> + clock-frequency = <400000>;
> + i2c-scl-rising-time-ns = <160>;
> + i2c-scl-falling-time-ns = <30>;
sort
> + status = "okay";
> +
> + temp at 4c {
> + compatible = "national,lm75";
> + reg = <0x4c>;
> + };
> +};
> +
> +&io_domains {
> + audio-supply = <&vcc1v8_sys_s0>;
> + bt656-supply = <&vcc1v8_sys_s0>;
> + gpio1830-supply = <&vcc3v0_s3>;
> + sdmmc-supply = <&vcc_sdio_s0>;
> + status = "okay";
> +};
> +
> +&pinctrl {
> + gmac {
> + rgmii_phy_reset: rgmii-phy-reset {
> + rockchip,pins =
> + <3 RK_PB7 RK_FUNC_GPIO &pcfg_output_low>;
align on the same line similar to pmic
> + };
> + };
> +
> + leds {
> + fault_led: fault-led {
> + rockchip,pins =
> + <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_down>;
align
> + };
> +
> + status_led: status-led {
> + rockchip,pins =
> + <0 RK_PB4 RK_FUNC_GPIO &pcfg_pull_down>,
align
> + };
> + };
> +
> + pmic {
> + pmic_int_l: pmic-int-l {
> + rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + vsel1_gpio: vsel1-gpio {
> + rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> +
> + vsel2_gpio: vsel2-gpio {
> + rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +};
> +
> +&pmu_io_domains {
> + pmu1830-supply = <&vcc3v0_s3>;
> + status = "okay";
> +};
> +
> +&sdhci {
> + bus-width = <8>;
> + disable-wp;
remove
not used with emmc
> + mmc-hs200-1_8v;
> + non-removable;
> + supports-emmc;
remove
not a valid property for mainline
> + vqmmc-supply = <&vcc1v8_sys_s0>;
> + status = "okay";
> +};
> +
> +&sdmmc {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
see regulator?
> + disable-wp;
> + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
> + pinctrl-names = "default";
> + vmmc-supply = <&vcc3v0_sd>;
> + vqmmc-supply = <&vcc_sdio_s0>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
>
More information about the Linux-rockchip
mailing list