[PATCH 07/16] configs: Enable USB host on Rock-PI-N10

[Kever Yang]

Hi Jagan,

     For the same board config, please just enable all the features you 
need in one patch

since the drivers already there, no need the split them into pieces.


     BTW: please add prefix "rockchip" in subject

Thanks,

- Kever

On 2020/7/21 上午2:51, Jagan Teki wrote:
> From: Suniel Mahesh <sunil at amarulasolutions.com>
>
> Enable USB 3.0 and 2.0 and related configs for the Rock-PI-N10
> target, which hosts RK3399Pro-VMARC-SOM.
>
> Log:
> Bus usb at fe380000: USB EHCI 1.00
> Bus usb at fe3c0000: USB EHCI 1.00
> Bus dwc3: usb maximum-speed not found
> Register 2000140 NbrPorts 2
> Starting the controller
> USB XHCI 1.10
> scanning bus usb at fe380000 for devices... 1 USB Device(s) found
> scanning bus usb at fe3c0000 for devices... 1 USB Device(s) found
> scanning bus dwc3 for devices... cannot reset port 1!?
> 2 USB Device(s) found
>          scanning usb for storage devices... 1 Storage Device(s) found
> => usb tree
> USB device tree:
>          1  Hub (480 Mb/s, 0mA)
>                  u-boot EHCI Host Controller
>
>          1  Hub (480 Mb/s, 0mA)
>                  u-boot EHCI Host Controller
>
>          1  Hub (5 Gb/s, 0mA)
>          |  U-Boot XHCI Host Controller
>          |
>          +-2  Mass Storage (5 Gb/s, 224mA)
>                  SanDisk Dual Drive 04019c9b2e1a58f24ee318c3c123aa5
> => usb tree
> USB device tree:
> 1  Hub (480 Mb/s, 0mA)
> |  u-boot EHCI Host Controller
> |
> +-2  Mass Storage (480 Mb/s, 224mA)
>          SanDisk Dual Drive 04019c9b2e1a58f24ee318c3c123aa5
>
> 1  Hub (480 Mb/s, 0mA)
>     u-boot EHCI Host Controller
>
> Signed-off-by: Suniel Mahesh <sunil at amarulasolutions.com>
> Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
> ---
>   configs/rock-pi-n10-rk3399pro_defconfig | 13 +++++++++++++
>   1 file changed, 13 insertions(+)
>
> diff --git a/configs/rock-pi-n10-rk3399pro_defconfig b/configs/rock-pi-n10-rk3399pro_defconfig
> index c705ce01ce..e09e656fbc 100644
> --- a/configs/rock-pi-n10-rk3399pro_defconfig
> +++ b/configs/rock-pi-n10-rk3399pro_defconfig
> @@ -19,6 +19,7 @@ CONFIG_TPL=y
>   CONFIG_CMD_BOOTZ=y
>   CONFIG_CMD_GPT=y
>   CONFIG_CMD_MMC=y
> +CONFIG_CMD_USB=y
>   # CONFIG_CMD_SETEXPR is not set
>   CONFIG_CMD_TIME=y
>   CONFIG_SPL_OF_CONTROL=y
> @@ -36,11 +37,23 @@ CONFIG_MMC_SDHCI_ROCKCHIP=y
>   CONFIG_DM_ETH=y
>   CONFIG_ETH_DESIGNWARE=y
>   CONFIG_GMAC_ROCKCHIP=y
> +CONFIG_PHY_ROCKCHIP_INNO_USB2=y
> +CONFIG_PHY_ROCKCHIP_TYPEC=y
>   CONFIG_PMIC_RK8XX=y
>   CONFIG_REGULATOR_PWM=y
>   CONFIG_REGULATOR_RK8XX=y
>   CONFIG_PWM_ROCKCHIP=y
> +CONFIG_DM_RESET=y
>   CONFIG_BAUDRATE=1500000
>   CONFIG_DEBUG_UART_SHIFT=2
>   CONFIG_SYSRESET=y
> +CONFIG_USB=y
> +CONFIG_USB_XHCI_HCD=y
> +CONFIG_USB_XHCI_DWC3=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_EHCI_GENERIC=y
> +CONFIG_USB_DWC3=y
> +CONFIG_USB_DWC3_GENERIC=y
> +CONFIG_USB_KEYBOARD=y
> +# CONFIG_USB_KEYBOARD_FN_KEYS is not set
>   CONFIG_ERRNO_STR=y