[PATCH 1/3] dt-bindings: Add document for rockchip RGB output interface

Rob Herring robh at kernel.org
Tue Sep 19 07:46:21 PDT 2017


On Thu, Sep 14, 2017 at 11:43:18AM +0800, Sandy Huang wrote:
> This path add support rv1108 rgb output interface driver.
> 
> Signed-off-by: Sandy Huang <hjc at rock-chips.com>
> ---
>  .../bindings/display/rockchip/rockchip-rgb.txt     | 80 ++++++++++++++++++++++
>  1 file changed, 80 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt
> 
> diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt
> new file mode 100644
> index 0000000..4164512
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt
> @@ -0,0 +1,80 @@
> +Rockchip RV1108 RGB interface
> +================================
> +
> +Required properties:
> +- compatible: matching the soc type:
> +	- "rockchip,rv1108-rgb";
> +
> +Optional properties:
> +- pinctrl-names: must contain a "lcdc" entry.
> +- pinctrl-0: pin control group to be used for this interface.
> +
> +Required nodes:
> +- rockchip,rgb-mode: should be "p888", "p666", "p565", "s888", "s888-dummy"

This should be a standard property. Any device with a parallel interface 
is going to need something like this.

> +	- p888: output r8-g8-b8 at each dclk cycle for per-pixel
> +	- p666: output r6-g6-b6 at each dclk cycle for per-pixel
> +	- p565: output r5-g6-b5 at each dclk cycle for per-pixel
> +	- s888: output r8-g8-b8 in three dclk cycle for per-pixel
> +	- s888-dmmy: output r8-g8-b8-dummy in four dclk cycle for per-pixel
> +
> +The rgb has two video ports described by:
> +	Documentation/devicetree/bindings/media/video-interfaces.txt
> +Their connections are modeled using the OF graph bindings specified in
> +	Documentation/devicetree/bindings/graph.txt.
> +
> +- video port 0 for the VOP input, the remote endpoint maybe vopb/vopl/vop
> +- video port 1 for either a panel or subsequent encoder
> +
> +the panel described by:
> +	Documentation/devicetree/bindings/display/panel/simple-panel.txt
> +Panel other required properties:
> +- ports for remote rgb output.
> +
> +Example:
> +
> +panel: panel {
> +	compatible = "auo,b101ean01";
> +	enable-gpios = <&gpio7 21 GPIO_ACTIVE_HIGH>;
> +
> +	ports {
> +		panel_in_rgb: endpoint {
> +			remote-endpoint = <&rgb_out_panel>;
> +		};
> +	};
> +};
> +
> +For Rockchip RV1108:
> +
> +	rgb: rgb {
> +		compatible = "rockchip,rv1108-rgb";
> +		pinctrl-names = "lcdc";
> +		pinctrl-0 = <&lcdc_ctl>;
> +		rockchip,rgb-mode = "p888";
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			rgb_in: port at 0 {
> +				reg = <0>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				rgb_in_vop: endpoint at 0 {
> +					reg = <0>;

Don't need reg for a single endpoint.

> +					remote-endpoint = <&vop_out_rgb>;
> +				};
> +			};
> +
> +			rgb_out: port at 1 {
> +				reg = <1>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				rgb_out_panel: endpoint at 0 {
> +					reg = <0>;

ditto.

> +					remote-endpoint = <&panel_in_rgb>;
> +				};
> +			};
> +		};
> +	};
> -- 
> 2.7.4
> 
> 



More information about the Linux-rockchip mailing list