[PATCH 2/5] thermal: rockchip: Support the RV1108 SoC in thermal driver

[Caesar Wang]

Hi Rocky,

在 2017年08月24日 18:27, Rocky Hao 写道:
> RV1108 SOC has one Temperature Sensor for CPU.
>
> Signed-off-by: Rocky Hao <rocky.hao at rock-chips.com>
> ---
>   drivers/thermal/rockchip_thermal.c | 67 ++++++++++++++++++++++++++++++++++++++
>   1 file changed, 67 insertions(+)
>
> diff --git a/drivers/thermal/rockchip_thermal.c b/drivers/thermal/rockchip_thermal.c
> index 9da3e1819210..299a8ade71fa 100644
> --- a/drivers/thermal/rockchip_thermal.c
> +++ b/drivers/thermal/rockchip_thermal.c
> @@ -242,6 +242,45 @@ struct tsadc_table {
>   	int temp;
>   };
>   
> +static const struct tsadc_table rv1108_table[] = {
> +	{0, -40000},
> +	{374, -40000},
> +	{382, -35000},
> +	{389, -30000},
> +	{397, -25000},
> +	{405, -20000},
> +	{413, -15000},
> +	{421, -10000},
> +	{429, -5000},
> +	{436, 0},
> +	{444, 5000},
> +	{452, 10000},
> +	{460, 15000},
> +	{468, 20000},
> +	{476, 25000},
> +	{483, 30000},
> +	{491, 35000},
> +	{499, 40000},
> +	{507, 45000},
> +	{515, 50000},
> +	{523, 55000},
> +	{531, 60000},
> +	{539, 65000},
> +	{547, 70000},
> +	{555, 75000},
> +	{562, 80000},
> +	{570, 85000},
> +	{578, 90000},
> +	{586, 95000},
> +	{594, 100000},
> +	{602, 105000},
> +	{610, 110000},
> +	{618, 115000},
> +	{626, 120000},
> +	{634, 125000},
> +	{TSADCV2_DATA_MASK, 125000},
> +};
> +

 From the RV1108 TRM said,  this table was used for  the negative 
temperature coefficient.
But the default table is positive temperature coefficient, why?
I think you don't need to use the negative temperature coefficient.

>   static const struct tsadc_table rk3228_code_table[] = {
>   	{0, -40000},
>   	{588, -40000},
> @@ -779,6 +818,30 @@ static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
>   	writel_relaxed(val, regs + TSADCV2_INT_EN);
>   }
>   
> +static const struct rockchip_tsadc_chip rv1108_tsadc_data = {
> +	.chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */
> +	.chn_num = 1, /* one channel for tsadc */
> +
> +	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
> +	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
> +	.tshut_temp = 95000,
> +
> +	.initialize = rk_tsadcv2_initialize,
> +	.irq_ack = rk_tsadcv3_irq_ack,
> +	.control = rk_tsadcv3_control,

If you will use the positive temperature coefficient, we need change it.

.control = rk_tsadcv2_control,



> +	.get_temp = rk_tsadcv2_get_temp,
> +	.set_alarm_temp = rk_tsadcv2_alarm_temp,
> +	.set_tshut_temp = rk_tsadcv2_tshut_temp,
> +	.set_tshut_mode = rk_tsadcv2_tshut_mode,
> +
> +	.table = {
> +		.id = rv1108_table,
> +		.length = ARRAY_SIZE(rv1108_table),
> +		.data_mask = TSADCV2_DATA_MASK,
> +		.mode = ADC_INCREMENT,

Ditto

-Caesar


> +	},
> +};
> +
>   static const struct rockchip_tsadc_chip rk3228_tsadc_data = {
>   	.chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */
>   	.chn_num = 1, /* one channel for tsadc */
> @@ -928,6 +991,10 @@ static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
>   
>   static const struct of_device_id of_rockchip_thermal_match[] = {
>   	{
> +		.compatible = "rockchip,rv1108-tsadc",
> +		.data = (void *)&rv1108_tsadc_data,
> +	},
> +	{
>   		.compatible = "rockchip,rk3228-tsadc",
>   		.data = (void *)&rk3228_tsadc_data,
>   	},