[PATCH v4 2/7] mfd: rk808: add rk805 regs addr and ID

[Lee Jones]

On Fri, 17 Mar 2017, Elaine Zhang wrote:

> Signed-off-by: Elaine Zhang <zhangqing at rock-chips.com>
> ---
>  include/linux/mfd/rk808.h | 119 ++++++++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 119 insertions(+)
> 
> diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
> index 54feb140c210..a133309b52f9 100644
> --- a/include/linux/mfd/rk808.h
> +++ b/include/linux/mfd/rk808.h
> @@ -206,6 +206,96 @@ enum rk818_reg {
>  #define RK818_USB_ILMIN_2000MA		0x7
>  #define RK818_USB_CHG_SD_VSEL_MASK	0x70
>  
> +/* RK805 */
> +enum rk805_reg {
> +	RK805_ID_DCDC1,
> +	RK805_ID_DCDC2,
> +	RK805_ID_DCDC3,
> +	RK805_ID_DCDC4,
> +	RK805_ID_LDO1,
> +	RK805_ID_LDO2,
> +	RK805_ID_LDO3,
> +};
> +
> +/* INTERRUPT REGISTER */
> +#define RK805_INT_STS_REG		0x4C
> +#define RK805_INT_STS_MSK_REG		0x4D
> +#define RK805_GPIO_IO_POL_REG		0x50
> +#define RK805_OUT_REG			0x52
> +#define RK805_ON_SOURCE_REG		0xAE
> +#define RK805_OFF_SOURCE_REG		0xAF
> +
> +/* POWER CHANNELS ENABLE REGISTER */
> +#define RK805_DCDC_EN_REG		0x23
> +#define RK805_SLP_DCDC_EN_REG		0x25
> +#define RK805_SLP_LDO_EN_REG		0x26
> +#define RK805_LDO_EN_REG		0x27
> +
> +/* CONFIG REGISTER */
> +#define RK805_THERMAL_REG		0x22
> +
> +/* BUCK AND LDO CONFIG REGISTER */
> +#define RK805_BUCK_LDO_SLP_LP_EN_REG	0x2A
> +#define RK805_BUCK1_CONFIG_REG		0x2E
> +#define RK805_BUCK1_ON_VSEL_REG		0x2F
> +#define RK805_BUCK1_SLP_VSEL_REG	0x30
> +#define RK805_BUCK2_CONFIG_REG		0x32
> +#define RK805_BUCK2_ON_VSEL_REG		0x33
> +#define RK805_BUCK2_SLP_VSEL_REG	0x34
> +#define RK805_BUCK3_CONFIG_REG		0x36
> +#define RK805_BUCK4_CONFIG_REG		0x37
> +#define RK805_BUCK4_ON_VSEL_REG		0x38
> +#define RK805_BUCK4_SLP_VSEL_REG	0x39
> +#define RK805_LDO1_ON_VSEL_REG		0x3B
> +#define RK805_LDO1_SLP_VSEL_REG		0x3C
> +#define RK805_LDO2_ON_VSEL_REG		0x3D
> +#define RK805_LDO2_SLP_VSEL_REG		0x3E
> +#define RK805_LDO3_ON_VSEL_REG		0x3F
> +#define RK805_LDO3_SLP_VSEL_REG		0x40
> +#define RK805_OUT_REG			0x52
> +#define RK805_ON_SOURCE_REG		0xAE
> +#define RK805_OFF_SOURCE_REG		0xAF

Why aren't all of these in numerical order?

> +#define RK805_NUM_REGULATORS		7
> +
> +#define RK805_PWRON_FALL_RISE_INT_EN	0x0
> +#define RK805_PWRON_FALL_RISE_INT_MSK	0x81
> +
> +/* RK805 IRQ Definitions */
> +#define RK805_IRQ_PWRON_RISE		0
> +#define RK805_IRQ_VB_LOW		1
> +#define RK805_IRQ_PWRON			2
> +#define RK805_IRQ_PWRON_LP		3
> +#define RK805_IRQ_HOTDIE		4
> +#define RK805_IRQ_RTC_ALARM		5
> +#define RK805_IRQ_RTC_PERIOD		6
> +#define RK805_IRQ_PWRON_FALL		7
> +
> +#define RK805_IRQ_PWRON_RISE_MSK	BIT(0)
> +#define RK805_IRQ_VB_LOW_MSK		BIT(1)
> +#define RK805_IRQ_PWRON_MSK		BIT(2)
> +#define RK805_IRQ_PWRON_LP_MSK		BIT(3)
> +#define RK805_IRQ_HOTDIE_MSK		BIT(4)
> +#define RK805_IRQ_RTC_ALARM_MSK		BIT(5)
> +#define RK805_IRQ_RTC_PERIOD_MSK	BIT(6)
> +#define RK805_IRQ_PWRON_FALL_MSK	BIT(7)
> +
> +#define RK805_PWR_RISE_INT_STATUS	BIT(0)
> +#define RK805_VB_LOW_INT_STATUS		BIT(1)
> +#define RK805_PWRON_INT_STATUS		BIT(2)
> +#define RK805_PWRON_LP_INT_STATUS	BIT(3)
> +#define RK805_HOTDIE_INT_STATUS		BIT(4)
> +#define RK805_ALARM_INT_STATUS		BIT(5)
> +#define RK805_PERIOD_INT_STATUS		BIT(6)
> +#define RK805_PWR_FALL_INT_STATUS	BIT(7)
> +
> +#define RK805_BUCK1_2_ILMAX_MASK	(3 << 6)
> +#define RK805_BUCK3_4_ILMAX_MASK        (3 << 3)
> +#define RK805_RTC_PERIOD_INT_MASK	(1 << 6)
> +#define RK805_RTC_ALARM_INT_MASK	(1 << 5)
> +#define RK805_INT_ALARM_EN		(1 << 3)
> +#define RK805_INT_TIMER_EN		(1 << 2)
> +
>  /* RK808 IRQ Definitions */
>  #define RK808_IRQ_VOUT_LO	0
>  #define RK808_IRQ_VB_LO		1
> @@ -298,7 +388,14 @@ enum rk818_reg {
>  #define VOUT_LO_INT	BIT(0)
>  #define CLK32KOUT2_EN	BIT(0)
>  
> +#define TEMP115C			0x0c
> +#define TEMP_HOTDIE_MSK			0x0c
> +#define SLP_SD_MSK			(0x3 << 2)
> +#define SHUTDOWN_FUN			(0x2 << 2)
> +#define SLEEP_FUN			(0x1 << 2)
>  #define RK8XX_ID_MSK			0xfff0
> +#define FPWM_MODE			BIT(7)
> +
>  enum {
>  	BUCK_ILMIN_50MA,
>  	BUCK_ILMIN_100MA,
> @@ -322,6 +419,28 @@ enum {
>  };
>  
>  enum {
> +	RK805_BUCK1_2_ILMAX_2500MA,
> +	RK805_BUCK1_2_ILMAX_3000MA,
> +	RK805_BUCK1_2_ILMAX_3500MA,
> +	RK805_BUCK1_2_ILMAX_4000MA,
> +};
> +
> +enum {
> +	RK805_BUCK3_ILMAX_1500MA,
> +	RK805_BUCK3_ILMAX_2000MA,
> +	RK805_BUCK3_ILMAX_2500MA,
> +	RK805_BUCK3_ILMAX_3000MA,
> +};
> +
> +enum {
> +	RK805_BUCK4_ILMAX_2000MA,
> +	RK805_BUCK4_ILMAX_2500MA,
> +	RK805_BUCK4_ILMAX_3000MA,
> +	RK805_BUCK4_ILMAX_3500MA,
> +};
> +
> +enum {
> +	RK805_ID = 0x8050,
>  	RK808_ID = 0x0000,
>  	RK818_ID = 0x8181,
>  };

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog