[PATCH v2 2/3] ARM: dts: rockchip: Add support for PCM-947 carrier board
Wadim Egorov
w.egorov at phytec.de
Thu Apr 6 06:04:25 PDT 2017
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Following interfaces and devices are available on the PCM-947 carrier board:
- 2x UART
- micro SDMMC
- USB host and USB otg
- USB 3503 HSIC hub
- Ethernet
- 2nd alternative KSZ9031 ethernet phy
- Display connectors: PHYTEC LVDS, DDG LVDS, parallel signals, HDMI
- Parallel Camera CIF
- SGTL5000-32QFN audio codec
- 4x LEDs connected via PCA9533
- 2 user buttons
- Expansion connectors for WiFi and other modules
- RTC RV-4162-C7
- Resistive touch STMPE811
- EEPROM M24C32
Signed-off-by: Wadim Egorov <w.egorov at phytec.de>
---
Changes in v2:
- Added a dual license which is used for all rk3288 based boards.
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rk3288-phycore-rdk.dts | 298 +++++++++++++++++++++++++++++++
2 files changed, 299 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3288-phycore-rdk.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0118084..8c3cb4d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -692,6 +692,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3288-firefly.dtb \
rk3288-firefly-reload.dtb \
rk3288-miqi.dtb \
+ rk3288-phycore-rdk.dtb \
rk3288-popmetal.dtb \
rk3288-r89.dtb \
rk3288-rock2-square.dtb \
diff --git a/arch/arm/boot/dts/rk3288-phycore-rdk.dts b/arch/arm/boot/dts/rk3288-phycore-rdk.dts
new file mode 100644
index 0000000..870f96b
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-phycore-rdk.dts
@@ -0,0 +1,298 @@
+/*
+ * Device tree file for Phytec PCM-947 carrier board
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov at phytec.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/leds-pca9532.h>
+#include "rk3288-phycore-som.dtsi"
+
+/ {
+ model = "Phytec RK3288 PCM-947";
+ compatible = "phytec,rk3288-pcm-947", "phytec,rk3288-phycore-som", "rockchip,rk3288";
+
+ user_buttons: user-buttons {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_button_pins>;
+
+ button at 0 {
+ label = "home";
+ linux,code = <KEY_HOME>;
+ gpios = <&gpio8 0 GPIO_ACTIVE_HIGH>;
+ wakeup-source;
+ };
+
+ button at 1 {
+ label = "menu";
+ linux,code = <KEY_MENU>;
+ gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
+ wakeup-source;
+ };
+ };
+
+ vcc_host0_5v: usb-host0-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host0_vbus_drv>;
+ regulator-name = "vcc_host0_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&vdd_in_otg_out>;
+ };
+
+ vcc_host1_5v: usb-host1-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host1_vbus_drv>;
+ regulator-name = "vcc_host1_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&vdd_in_otg_out>;
+ };
+
+ vcc_otg_5v: usb-otg-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio2 12 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&otg_vbus_drv>;
+ regulator-name = "vcc_otg_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&vdd_in_otg_out>;
+ };
+};
+
+&gmac {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+
+ stmpe at 44 {
+ compatible = "st,stmpe811";
+ reg = <0x44>;
+ };
+
+ adc at 64 {
+ compatible = "maxim,max1037";
+ reg = <0x64>;
+ };
+
+ i2c_rtc: rtc at 68 {
+ compatible = "rv4162";
+ reg = <0x68>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_rtc_int>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <10 0>;
+ };
+};
+
+&i2c3 {
+ status = "okay";
+
+ i2c_eeprom_cb: eeprom at 51 {
+ compatible = "atmel,24c32";
+ reg = <0x51>;
+ pagesize = <32>;
+ };
+};
+
+&i2c4 {
+ status = "okay";
+
+ /* PCA9533 - 4-bit LED dimmer */
+ leddim: leddimmer at 62 {
+ compatible = "nxp,pca9533";
+ reg = <0x62>;
+
+ led1 {
+ label = "red:user1";
+ linux,default-trigger = "none";
+ type = <PCA9532_TYPE_LED>;
+ };
+
+ led2 {
+ label = "green:user2";
+ linux,default-trigger = "none";
+ type = <PCA9532_TYPE_LED>;
+ };
+
+ led3 {
+ label = "blue:user3";
+ linux,default-trigger = "none";
+ type = <PCA9532_TYPE_LED>;
+ };
+
+ led4 {
+ label = "red:user4";
+ linux,default-trigger = "none";
+ type = <PCA9532_TYPE_LED>;
+ };
+ };
+};
+
+&i2c5 {
+ status = "okay";
+};
+
+&pinctrl {
+ pcfg_pull_up_drv_12ma: pcfg-pull-up-drv-12ma {
+ bias-pull-up;
+ drive-strength = <12>;
+ };
+
+ buttons {
+ user_button_pins: user-button-pins {
+ /* button 1 */
+ rockchip,pins = <8 3 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* button 2 */
+ <8 0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ rv4162 {
+ i2c_rtc_int: i2c-rtc-int {
+ rockchip,pins = <5 10 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ sdmmc {
+ /*
+ * Default drive strength isn't enough to achieve even
+ * high-speed mode on pcm-947 board so bump up to 12 mA.
+ */
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+ <6 17 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+ <6 18 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+ <6 19 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
+ };
+
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_12ma>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
+ };
+
+ sdmmc_pwr: sdmmc-pwr {
+ rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ touchscreen {
+ ts_irq_pin: ts-irq-pin {
+ rockchip,pins = <5 15 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb_host {
+ host0_vbus_drv: host0-vbus-drv {
+ rockchip,pins = <2 13 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ host1_vbus_drv: host1-vbus-drv {
+ rockchip,pins = <2 0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb_otg {
+ otg_vbus_drv: otg-vbus-drv {
+ rockchip,pins = <2 12 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ card-detect-delay = <200>;
+ disable-wp;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+ vmmc-supply = <&vdd_io_sd>;
+ vqmmc-supply = <&vdd_io_sd>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host1 {
+ status = "okay";
+};
+
+&usb_otg {
+ status = "okay";
+};
--
1.9.1
More information about the Linux-rockchip
mailing list