[PATCH] arm: dts: fix rk3066a based boards vdd_log voltage initialization

[Heiko Stuebner]

Am Montag, 19. September 2016, 08:15:30 CEST schrieb Doug Anderson:
> Hi,
> 
> On Mon, Sep 19, 2016 at 1:44 AM, Andy Yan <andy.yan at rock-chips.com> wrote:
> > The current rk3066a based boards(Rayeager, Bqcurie2, Marsboard) use
> > pwm modulate vdd_logic voltage, but the pwm is default disabled and
> > the pwm pin acts as a gpio before pwm regulator probed, so the pwm
> > regulator driver will get a zero dutycycle at probe time, so change
> > the initial dutycycle to zero to match pwm_regulator_init_state check.
> > 
> > Signed-off-by: Andy Yan <andy.yan at rock-chips.com>
> > 
> > ---
> > 
> >  arch/arm/boot/dts/rk3066a-bqcurie2.dts  | 2 +-
> >  arch/arm/boot/dts/rk3066a-marsboard.dts | 2 +-
> >  arch/arm/boot/dts/rk3066a-rayeager.dts  | 2 +-
> >  3 files changed, 3 insertions(+), 3 deletions(-)
> > 
> > diff --git a/arch/arm/boot/dts/rk3066a-bqcurie2.dts
> > b/arch/arm/boot/dts/rk3066a-bqcurie2.dts index bc674ee..618450d 100644
> > --- a/arch/arm/boot/dts/rk3066a-bqcurie2.dts
> > +++ b/arch/arm/boot/dts/rk3066a-bqcurie2.dts
> > @@ -61,7 +61,7 @@
> > 
> >                 regulator-min-microvolt = <1200000>;
> >                 regulator-max-microvolt = <1200000>;
> >                 regulator-always-on;
> > 
> > -               voltage-table = <1000000 100>,
> > +               voltage-table = <1000000 0>,
> 
> In my opinion this isn't quite the right answer.  I think that you
> should add a new property describing the voltage in the case that the
> pin is an input and you should fill that property in, like:
> 
>   voltage-when-input = <1000000>;

I'd think this would be more of a pwm issue, not something the pwm-regulator 
should need to care about.

Ideally the pwm driver should be able to return some state information even if 
disabled? I.e. deriving a duty-cycle value from its pin state similar to what 
Doug described below (it's either 0% or 100%)

But right now I have a hard time understanding how the pwm could return any 
duty-cycle information for an input gpio to the pwm-regulator, as I assume the 
pwm-driver has to probe (and thus set pinctrl to the pwm function) before the 
pwm-regulator is able to get the pwm handle?


> Once you have this property you should ideally be able to read whether
> the pin is currently configured as an input or as a special function
> at bootup.  Note that I don't actually know if this is possible with
> the current pinctrl API, but it does seem like the ideal way to do it
> since it means you'll work even if the BIOS changes (AKA: if the BIOS
> leaves the pin as an input you can keep the voltage the same and if
> the BIOS leaves the pin as PWM you can keep the voltage the same).
> 
> It's also possible that you could just add a property that says "init
> to a certain value at bootup no matter what the BIOS left it as".  As
> long as that voltage is the maximum (and you'll lower it later) this
> ought to be safe and you shouldn't risk temporarily undervolting
> things.
> 
> 
> Note that, if you haven't already done so, you almost certainly want
> to make sure your pinctrl species an "init" state in addition to a
> "default" state.  See <https://patchwork.kernel.org/patch/7454311/>.
> 
> -Doug