[PATCH 2/2] ARM64: dts: rockchip: use pin constants to describe gpios
Andy Yan
andy.yan at rock-chips.com
Sat Oct 22 05:59:04 PDT 2016
Use macros to describe gpios will make the dts easier to
read and write.
Signed-off-by: Andy Yan <andy.yan at rock-chips.com>
---
arch/arm64/boot/dts/rockchip/rk3368-evb.dtsi | 10 +++++-----
arch/arm64/boot/dts/rockchip/rk3368-geekbox.dts | 8 ++++----
arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts | 14 +++++++-------
arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dts | 4 ++--
arch/arm64/boot/dts/rockchip/rk3368-r88.dts | 16 ++++++++--------
arch/arm64/boot/dts/rockchip/rk3399-evb.dts | 6 +++---
6 files changed, 29 insertions(+), 29 deletions(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3368-evb.dtsi b/arch/arm64/boot/dts/rockchip/rk3368-evb.dtsi
index fff8b19..4772917 100644
--- a/arch/arm64/boot/dts/rockchip/rk3368-evb.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3368-evb.dtsi
@@ -90,7 +90,7 @@
240 241 242 243 244 245 246 247
248 249 250 251 252 253 254 255>;
default-brightness-level = <128>;
- enable-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+ enable-gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&bl_en>;
pwms = <&pwm0 0 1000000 PWM_POLARITY_INVERTED>;
@@ -101,7 +101,7 @@
compatible = "mmc-pwrseq-emmc";
pinctrl-0 = <&emmc_reset>;
pinctrl-names = "default";
- reset-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_HIGH>;
};
keys: gpio-keys {
@@ -111,7 +111,7 @@
power {
wakeup-source;
- gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
label = "GPIO Power";
linux,code = <KEY_POWER>;
};
@@ -121,7 +121,7 @@
vcc_host: vcc-host-regulator {
compatible = "regulator-fixed";
enable-active-high;
- gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+ gpio = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&host_vbus_drv>;
regulator-name = "vcc_host";
@@ -166,7 +166,7 @@
phy-supply = <&vcc_lan>;
phy-mode = "rmii";
clock_in_out = "output";
- snps,reset-gpio = <&gpio3 12 0>;
+ snps,reset-gpio = <&gpio3 RK_PB4 GPIO_ACTIVE_HIGH>;
snps,reset-active-low;
snps,reset-delays-us = <0 10000 1000000>;
pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/rockchip/rk3368-geekbox.dts b/arch/arm64/boot/dts/rockchip/rk3368-geekbox.dts
index e5eeca2..e5b92d2 100644
--- a/arch/arm64/boot/dts/rockchip/rk3368-geekbox.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3368-geekbox.dts
@@ -66,7 +66,7 @@
ir: ir-receiver {
compatible = "gpio-ir-receiver";
- gpios = <&gpio3 30 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio3 RK_PD6 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&ir_int>;
};
@@ -77,7 +77,7 @@
pinctrl-0 = <&pwr_key>;
power {
- gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
label = "GPIO Power";
linux,code = <KEY_POWER>;
wakeup-source;
@@ -88,13 +88,13 @@
compatible = "gpio-leds";
blue {
- gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_HIGH>;
label = "geekbox:blue:led";
default-state = "on";
};
red {
- gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_HIGH>;
label = "geekbox:red:led";
default-state = "off";
};
diff --git a/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
index ea0a8ec..2e431f13 100644
--- a/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
@@ -61,7 +61,7 @@
compatible = "mmc-pwrseq-emmc";
pinctrl-0 = <&emmc_reset>;
pinctrl-names = "default";
- reset-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_HIGH>;
};
ext_gmac: external-gmac-clock {
@@ -78,7 +78,7 @@
power {
wakeup-source;
- gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+ gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
label = "GPIO Power";
linux,code = <KEY_POWER>;
};
@@ -88,7 +88,7 @@
compatible = "gpio-leds";
red {
- gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ gpios = <&gpio3 RK_PD5 GPIO_ACTIVE_HIGH>;
label = "orion:red:led";
pinctrl-names = "default";
pinctrl-0 = <&led_ctl>;
@@ -96,7 +96,7 @@
};
blue {
- gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
label = "orion:blue:led";
pinctrl-names = "default";
pinctrl-0 = <&stby_pwren>;
@@ -117,7 +117,7 @@
/* supplies both host and otg */
vcc_host: vcc-host-regulator {
compatible = "regulator-fixed";
- gpio = <&gpio0 4 GPIO_ACTIVE_LOW>;
+ gpio = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&host_vbus_drv>;
regulator-name = "vcc_host";
@@ -149,7 +149,7 @@
vcc_sd: vcc-sd-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc_sd";
- gpio = <&gpio3 11 GPIO_ACTIVE_LOW>;
+ gpio = <&gpio3 RK_PB3 GPIO_ACTIVE_LOW>;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vcc_io>;
@@ -217,7 +217,7 @@
phy-mode = "rgmii";
pinctrl-names = "default";
pinctrl-0 = <&rgmii_pins>;
- snps,reset-gpio = <&gpio3 12 0>;
+ snps,reset-gpio = <&gpio3 RK_PB4 GPIO_ACTIVE_HIGH>;
snps,reset-active-low;
snps,reset-delays-us = <0 10000 1000000>;
tx_delay = <0x30>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dts b/arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dts
index 85f7a24..62919c4 100644
--- a/arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dts
@@ -63,7 +63,7 @@
pinctrl-0 = <&pwr_key>;
power {
- gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
label = "GPIO Power";
linux,code = <KEY_POWER>;
wakeup-source;
@@ -248,7 +248,7 @@
reg = <0x40>;
interrupt-parent = <&gpio3>;
interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
- power-gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+ power-gpios = <&gpio3 RK_PB7 GPIO_ACTIVE_HIGH>;
touchscreen-size-x = <800>;
touchscreen-size-y = <1280>;
silead,max-fingers = <5>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3368-r88.dts b/arch/arm64/boot/dts/rockchip/rk3368-r88.dts
index eed1ef6..7134181 100644
--- a/arch/arm64/boot/dts/rockchip/rk3368-r88.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3368-r88.dts
@@ -61,7 +61,7 @@
compatible = "mmc-pwrseq-emmc";
pinctrl-0 = <&emmc_reset>;
pinctrl-names = "default";
- reset-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_HIGH>;
};
keys: gpio-keys {
@@ -71,7 +71,7 @@
power {
wakeup-source;
- gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
label = "GPIO Power";
linux,code = <KEY_POWER>;
};
@@ -81,7 +81,7 @@
compatible = "gpio-leds";
work {
- gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ gpios = <&gpio3 RK_PD5 GPIO_ACTIVE_HIGH>;
label = "r88:green:led";
pinctrl-names = "default";
pinctrl-0 = <&led_ctl>;
@@ -90,7 +90,7 @@
ir: ir-receiver {
compatible = "gpio-ir-receiver";
- gpios = <&gpio3 30 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio3 RK_PD6 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&ir_int>;
};
@@ -104,10 +104,10 @@
reset-gpios =
/* BT_RST_N */
- <&gpio3 5 GPIO_ACTIVE_LOW>,
+ <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>,
/* WL_REG_ON */
- <&gpio3 4 GPIO_ACTIVE_LOW>;
+ <&gpio3 RK_PA4 GPIO_ACTIVE_LOW>;
};
vcc_18: vcc18-regulator {
@@ -124,7 +124,7 @@
vcc_host: vcc-host-regulator {
compatible = "regulator-fixed";
enable-active-high;
- gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+ gpio = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&host_vbus_drv>;
regulator-name = "vcc_host";
@@ -199,7 +199,7 @@
phy-supply = <&vcc_lan>;
phy-mode = "rmii";
clock_in_out = "output";
- snps,reset-gpio = <&gpio3 12 0>;
+ snps,reset-gpio = <&gpio3 RK_PB4 GPIO_ACTIVE_HIGH>;
snps,reset-active-low;
snps,reset-delays-us = <0 10000 1000000>;
pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-evb.dts b/arch/arm64/boot/dts/rockchip/rk3399-evb.dts
index 8e82497..f00e0d5 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-evb.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-evb.dts
@@ -88,7 +88,7 @@
vcc5v0_host: vcc5v0-host-regulator {
compatible = "regulator-fixed";
enable-active-high;
- gpio = <&gpio4 25 GPIO_ACTIVE_HIGH>;
+ gpio = <&gpio4 RK_PD1 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&vcc5v0_host_en>;
regulator-name = "vcc5v0_host";
@@ -123,7 +123,7 @@
phy-mode = "rgmii";
pinctrl-names = "default";
pinctrl-0 = <&rgmii_pins>;
- snps,reset-gpio = <&gpio3 15 GPIO_ACTIVE_LOW>;
+ snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
snps,reset-active-low;
snps,reset-delays-us = <0 10000 50000>;
tx_delay = <0x28>;
@@ -156,7 +156,7 @@
};
&pcie0 {
- ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+ ep-gpios = <&gpio3 RK_PB5 GPIO_ACTIVE_HIGH>;
num-lanes = <4>;
pinctrl-names = "default";
pinctrl-0 = <&pcie_clkreqn>;
--
2.7.4
More information about the Linux-rockchip
mailing list