[PATCH 01/30] usb: dwc2: Deprecate g-use-dma binding

John Youn John.Youn at synopsys.com
Tue Nov 8 09:48:03 PST 2016


On 11/8/2016 1:12 AM, Felipe Balbi wrote:
> 
> Hi,
> 
> John Youn <johnyoun at synopsys.com> writes:
>> Add a vendor prefix and make the name more consistent by renaming it to
>> "snps,gadget-dma-enable".
>>
>> Signed-off-by: John Youn <johnyoun at synopsys.com>
>> ---
>>  Documentation/devicetree/bindings/usb/dwc2.txt | 5 ++++-
>>  arch/arm/boot/dts/rk3036.dtsi                  | 2 +-
>>  arch/arm/boot/dts/rk3288.dtsi                  | 2 +-
>>  arch/arm/boot/dts/rk3xxx.dtsi                  | 2 +-
>>  arch/arm64/boot/dts/hisilicon/hi6220.dtsi      | 2 +-
>>  arch/arm64/boot/dts/rockchip/rk3368.dtsi       | 2 +-
>>  drivers/usb/dwc2/params.c                      | 9 ++++++++-
>>  drivers/usb/dwc2/pci.c                         | 2 +-
>>  8 files changed, 18 insertions(+), 8 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt
>> index 9472111..389a461 100644
>> --- a/Documentation/devicetree/bindings/usb/dwc2.txt
>> +++ b/Documentation/devicetree/bindings/usb/dwc2.txt
>> @@ -26,11 +26,14 @@ Refer to phy/phy-bindings.txt for generic phy consumer properties
>>  - dr_mode: shall be one of "host", "peripheral" and "otg"
>>    Refer to usb/generic.txt
>>  - snps,host-dma-disable: disable host DMA mode.
>> -- g-use-dma: enable dma usage in gadget driver.
>> +- snps,gadget-dma-enable: enable gadget DMA mode.
> 
> I don't see why you even have this binding. Looking through the code,
> you have:
> 
> #define GHWCFG2_SLAVE_ONLY_ARCH			0
> #define GHWCFG2_EXT_DMA_ARCH			1
> #define GHWCFG2_INT_DMA_ARCH			2
> 
> void dwc2_set_param_dma_enable(struct dwc2_hsotg *hsotg, int val)
> {
> 	int valid = 1;
> 
> 	if (val > 0 && hsotg->hw_params.arch == GHWCFG2_SLAVE_ONLY_ARCH)
> 		valid = 0;
> 	if (val < 0)
> 		valid = 0;
> 
> 	if (!valid) {
> 		if (val >= 0)
> 			dev_err(hsotg->dev,
> 				"%d invalid for dma_enable parameter. Check HW configuration.\n",
> 				val);
> 		val = hsotg->hw_params.arch != GHWCFG2_SLAVE_ONLY_ARCH;
> 		dev_dbg(hsotg->dev, "Setting dma_enable to %d\n", val);
> 	}
> 
> 	hsotg->core_params->dma_enable = val;
> }
> 
> which seems to hint that DMA support is discoverable. If there is DMA,
> why would disable it?
> 

Yes that's the case and I would prefer to make it discoverable and
enabled by default.

But the legacy behavior has always been like this because DMA was
never fully implemented in the gadget driver and it was an opt-in
feature. Periodic support was only added recently.

What do you think about enabling it by default now? I think most
platforms already use DMA.

We would still need a "disable" binding for IP validation purposes at
least.

Regards,
John



More information about the Linux-rockchip mailing list