[PATCH v7 6/9] i2c: rk3x: Move spec timing data to "static const" structs

[Doug Anderson]

David,

On Wed, May 4, 2016 at 7:34 AM, David Wu <david.wu at rock-chips.com> wrote:
> Signed-off-by: David Wu <david.wu at rock-chips.com>

As you can probably guess, again a description would be nice.  Like maybe:

The i2c timing specs are really just constant data.  There's no reason
to write code to init them, so move them out to structures.  This not
only is a cleaner solution but it will reduce code duplication when we
introduce a new variant of rk3x_i2c_calc_divs() in a future patch.

That helps someone reading the patch understand the motivation.


> @@ -76,6 +76,51 @@ enum {
>  #define DEFAULT_SCL_RATE  (100 * 1000) /* Hz */
>
>  /**
> + * struct i2c_spec_values:
> + * @min_hold_start_ns: min hold time (repeated) START condition
> + * @min_low_ns: min LOW period of the SCL clock
> + * @min_high_ns: min HIGH period of the SCL cloc
> + * @min_setup_start_ns: min set-up time for a repeated START conditio
> + * @max_data_hold_ns: max data hold time
> + * @min_data_setup_ns: min data set-up time
> + * @min_setup_stop_ns: min set-up time for STOP condition
> + * @min_hold_buffer_ns: min bus free time between a STOP and
> + * START condition
> + */
> +struct i2c_spec_values {
> +       unsigned long min_hold_start_ns;
> +       unsigned long min_low_ns;
> +       unsigned long min_high_ns;
> +       unsigned long min_setup_start_ns;
> +       unsigned long max_data_hold_ns;
> +       unsigned long min_data_setup_ns;
> +       unsigned long min_setup_stop_ns;
> +       unsigned long min_hold_buffer_ns;
> +};
> +
> +static const struct i2c_spec_values standard_mode_spec = {
> +       .min_hold_start_ns = 4000,
> +       .min_low_ns = 4700,
> +       .min_high_ns = 4000,
> +       .min_setup_start_ns = 4700,
> +       .max_data_hold_ns = 3450,
> +       .min_data_setup_ns = 250,
> +       .min_setup_stop_ns = 4000,
> +       .min_hold_buffer_ns = 4700,

There are more spec values than are currently used in this patch.
Personally I'm OK with that, but if you wanted to be totally clean
this patch would only include the spec values that were needed, then
introduce the additional values in the rk3399 patch.


> @@ -492,6 +548,8 @@ static int rk3x_i2c_calc_divs(unsigned long clk_rate,
>         unsigned long min_div_for_hold, min_total_div;
>         unsigned long extra_div, extra_low_div, ideal_low_div;
>
> +       unsigned long data_hold_buffer_ns = 50;

aside (feel free to ignore): Gosh, I kinda forgot what the heck this
value was for.  I guess it's not anything in the spec.  I have a
feeling it was some sort of slop value that someone felt was
necessary, but I don't quite remember.  Oh well, I guess we leave it
there since I'd rather not mess with timings on old hardware that are
apparently working for everyone.  :-P


In any case, aside from the missing description:

Suggested-by: Douglas Anderson <dianders at chromium.org>
Reviewed-by: Douglas Anderson <dianders at chromium.org>

IMHO this can be applied any time independent of any earlier patches.


-Doug