[PATCH v3 2/2] phy: add a driver for the Rockchip SoC internal PCIe PHY

[Brian Norris]

Hi,

On Thu, Jun 23, 2016 at 10:30:17AM +0800, Shawn Lin wrote:
> 在 2016/6/20 14:36, Kishon Vijay Abraham I 写道:
> >On Monday 20 June 2016 06:28 AM, Shawn Lin wrote:
> >>On 2016/6/17 21:08, Kishon Vijay Abraham I wrote:
> >>>On Thursday 16 June 2016 06:52 AM, Shawn Lin wrote:
> >>>>This patch to add a generic PHY driver for rockchip PCIe PHY.
> >>>>Access the PHY via registers provided by GRF (general register
> >>>>files) module.
> >>>>
> >>>>Signed-off-by: Shawn Lin <shawn.lin at rock-chips.com>
> >>>>---
> >>>>
> >>>>Changes in v3: None
> >>>>Changes in v2: None
> >>>>
[...]
> >>>>diff --git a/drivers/phy/phy-rockchip-pcie.c b/drivers/phy/phy-rockchip-pcie.c
> >>>>new file mode 100644
> >>>>index 0000000..bc6cd17
> >>>>--- /dev/null
> >>>>+++ b/drivers/phy/phy-rockchip-pcie.c
> >>>>@@ -0,0 +1,378 @@

[...]

> >>>>+void rockchip_pcie_phy_laneoff(struct phy *phy)
> >>>>+{
> >>>>+    u32 status;
> >>>>+    struct rockchip_pcie_phy *rk_phy = phy_get_drvdata(phy);
> >>>>+    int i;
> >>>>+
> >>>>+    for (i = 0; i < PHY_MAX_LANE_NUM; i++) {
> >>>>+        status = phy_rd_cfg(rk_phy, PHY_LANE_A_STATUS + i);
> >>>>+        if (!((status >> PHY_LANE_RX_DET_SHIFT) &
> >>>>+               PHY_LANE_RX_DET_TH))
> >>>>+            pr_debug("lane %d is used\n", i);
> >>>>+        else
> >>>>+            regmap_write(rk_phy->reg_base,
> >>>>+                     rk_phy->phy_data->pcie_laneoff,
> >>>>+                     HIWORD_UPDATE(PHY_LANE_IDLE_OFF,
> >>>>+                           PHY_LANE_IDLE_MASK,
> >>>>+                           PHY_LANE_IDLE_A_SHIFT + i));
> >>>>+    }
> >>>>+}
> >>>>+EXPORT_SYMBOL_GPL(rockchip_pcie_phy_laneoff);

Shawn, I can't find an example of how you planned to use this (though I
can make educated guesses). As such, it's possible there's some
misunderstanding. Maybe you can include a sample patch for the PCIe
controller driver?

Related: it might make sense to have the PCIe controller and PHY
drivers/bindings all in the same patch series (with proper threading,
which we already talked about off-list).

> >>>Er.. don't use export symbols from phy driver. I think it would be nice if you
> >>>can model the driver in such a way that the PCIe driver can control individual
> >>>phy's.
> >>>
> >>
> >>Yes, I was trying to look for a way not to export symbols from
> >>phy... But I failed to find it as there at least need three
> >>interaction between controller and phy which made me believe we
> >>at least need to export one symbol without adding new API for phy.

My interpretation of the above is that Shawn means we might turn off up
to 3 different lanes (i.e., 3 of 4 supported lanes might be unused).

> >That can be managed by implementing a small state machine within the PHY driver.
> 
> I don't understand your point of implementing a small state machine
> within the PHY driver.

I'm not 100% sure I understand, but I think I have a reasonable
interpretation below.

> Do you mean I need to call vaarious of power_on/off and count the
> on/off times to decide the state machine?
> 
> I would appreciate it If you could elaborate this a bit more or
> show me a example. :)

My interpretation: rather than associating a single PCIe controller
device with a single struct phy that controls up to 4 lanes, Kishon is
suggesting you should have this driver implement 4 phy objects, one for
each lane. You'd need to add #phy-cells = <1> to the DT binding, and
implement an ->of_xlate() hook so we can associate/address them
properly. Then the PCIe controller would call phy_power_off() on each
lane that's not used.

The state machine would come into play because you have additional power
savings to utilize, but only when all PHYs are off. So the state machine
would just track how many of the lane PHYs are still on, and when the
count reaches 0, you call reset_control_assert(rk_phy->phy_rst).

The DT for this would be:

	pcie0: pcie at f8000000 {
		compatible = "rockchip,rk3399-pcie";
		...
		phys = <&pcie_phy 0>, <&pcie_phy 1>, <&pcie_phy 2>, <&pcie_phy 3>;
		phy-names = "pcie-lane0", "pcie-lane1", "pcie-lane2", "pcie-lane3";
		...
	};

	pcie_phy: pcie-phy {
		compatible = "rockchip,rk3399-pcie-phy";
		...
		#phy-cells = <1>;
		...
	};

(See Documentation/devicetree/bindings/phy/phy-bindings.txt for the
#phy-cells explanation.)

Is that close to what you're suggesting, Kishon? Seems reasonable enough
to me, even if it's slightly more complicated.

Brian