[v2, 2/2] phy: rockchip-inno-usb2: add a new driver for Rockchip usb2phy

[Guenter Roeck]

On Thu, Jun 02, 2016 at 02:48:10PM +0800, Frank Wang wrote:
> The newer SoCs (rk3366, rk3399) take a different usb-phy IP block
> than rk3288 and before, and most of phy-related registers are also
> different from the past, so a new phy driver is required necessarily.
> 
> Signed-off-by: Frank Wang <frank.wang at rock-chips.com>
> ---
> 
> Changes in v2:
>  - Changed vbus_host operation from gpio to regulator in *_probe.
>  - Improved the fault treatment relate to 480m clock register.
>  - Cleaned up some meaningless codes in *_clk480m_disable.
>  - made more clear the comment of *_sm_work.
> 
>  drivers/phy/Kconfig                  |    7 +
>  drivers/phy/Makefile                 |    1 +
>  drivers/phy/phy-rockchip-inno-usb2.c |  604 ++++++++++++++++++++++++++++++++++
>  3 files changed, 612 insertions(+)
>  create mode 100644 drivers/phy/phy-rockchip-inno-usb2.c
> 
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index b869b98..29ef15c 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -347,6 +347,13 @@ config PHY_ROCKCHIP_USB
>  	help
>  	  Enable this to support the Rockchip USB 2.0 PHY.
>  
> +config PHY_ROCKCHIP_INNO_USB2
> +	tristate "Rockchip INNO USB2PHY Driver"
> +	depends on ARCH_ROCKCHIP && OF
> +	select GENERIC_PHY
> +	help
> +	  Support for Rockchip USB2.0 PHY with Innosilicon IP block.
> +
>  config PHY_ROCKCHIP_EMMC
>  	tristate "Rockchip EMMC PHY Driver"
>  	depends on ARCH_ROCKCHIP && OF
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index 9c3e73c..4963fbc 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -38,6 +38,7 @@ phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2)	+= phy-s5pv210-usb2.o
>  obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
>  obj-$(CONFIG_PHY_QCOM_APQ8064_SATA)	+= phy-qcom-apq8064-sata.o
>  obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
> +obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
>  obj-$(CONFIG_PHY_ROCKCHIP_EMMC) += phy-rockchip-emmc.o
>  obj-$(CONFIG_PHY_ROCKCHIP_DP)		+= phy-rockchip-dp.o
>  obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
> diff --git a/drivers/phy/phy-rockchip-inno-usb2.c b/drivers/phy/phy-rockchip-inno-usb2.c
> new file mode 100644
> index 0000000..eca46ff
> --- /dev/null
> +++ b/drivers/phy/phy-rockchip-inno-usb2.c
> @@ -0,0 +1,604 @@
> +/*
> + * Rockchip USB2.0 PHY with Innosilicon IP block driver
> + *
> + * Copyright (C) 2016 Fuzhou Rockchip Electronics Co., Ltd
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/clk-provider.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/jiffies.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/of_irq.h>
> +#include <linux/of_platform.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/mfd/syscon.h>
> +
> +#define BIT_WRITEABLE_SHIFT	16
> +#define SCHEDULE_DELAY	(60 * HZ)
> +
> +enum rockchip_usb2phy_port_id {
> +	USB2PHY_PORT_OTG,
> +	USB2PHY_PORT_HOST,
> +	USB2PHY_NUM_PORTS,
> +};
> +
> +enum rockchip_usb2phy_host_state {
> +	PHY_STATE_HS_ONLINE	= 0,
> +	PHY_STATE_DISCONNECT	= 1,
> +	PHY_STATE_HS_CONNECT	= 2,
> +	PHY_STATE_FS_CONNECT	= 4,
> +};
> +
> +struct usb2phy_reg {
> +	unsigned int	offset;
> +	unsigned int	bitend;
> +	unsigned int	bitstart;
> +	unsigned int	disable;
> +	unsigned int	enable;
> +};
> +
> +/**
> + * struct rockchip_usb2phy_port_cfg: usb-phy port configuration.
> + * @phy_sus: phy suspend register.
> + * @ls_det_en: linestate detection enable register.
> + * @ls_det_st: linestate detection state register.
> + * @ls_det_clr: linestate detection clear register.
> + * @utmi_ls: utmi linestate state register.
> + * @utmi_hstdet: utmi host disconnect register.
> + */
> +struct rockchip_usb2phy_port_cfg {
> +	struct usb2phy_reg	phy_sus;
> +	struct usb2phy_reg	ls_det_en;
> +	struct usb2phy_reg	ls_det_st;
> +	struct usb2phy_reg	ls_det_clr;
> +	struct usb2phy_reg	utmi_ls;
> +	struct usb2phy_reg	utmi_hstdet;
> +};
> +
> +/**
> + * struct rockchip_usb2phy_cfg: usb-phy configuration.
> + * @num_ports: specify how many ports that the phy has.
> + * @clkout_ctl: keep on/turn off output clk of phy.
> + */
> +struct rockchip_usb2phy_cfg {
> +	unsigned int	num_ports;
> +	struct usb2phy_reg	clkout_ctl;
> +	const struct rockchip_usb2phy_port_cfg	*port_cfgs;
> +};
> +
> +/**
> + * struct rockchip_usb2phy_port: usb-phy port data.
> + * @port_id: flag for otg port or host port.
> + * @suspended: phy suspended flag.
> + * @ls_irq: IRQ number assigned for linestate detection.
> + * @mutex: for register updating in sm_work.
> + * @sm_work: OTG state machine work.
> + * @phy_cfg: port register configuration, assigned by driver data.
> + */
> +struct rockchip_usb2phy_port {
> +	struct phy	*phy;
> +	unsigned int	port_id;
> +	bool		suspended;
> +	int		ls_irq;
> +	struct mutex	mutex;
> +	struct		delayed_work sm_work;
> +	const struct	rockchip_usb2phy_port_cfg *port_cfg;
> +};
> +
> +/**
> + * struct rockchip_usb2phy: usb2.0 phy driver data.
> + * @grf: General Register Files regmap.
> + * @clk480m: clock struct of phy output clk.
> + * @clk_hw: clock struct of phy output clk management.
> + * @vbus_host: the regulator for vbus_host supply.
> + * @phy_cfg: phy register configuration, assigned by driver data.
> + * @ports: phy port instance.
> + */
> +struct rockchip_usb2phy {
> +	struct device	*dev;
> +	struct regmap	*grf;
> +	struct clk	*clk480m;
> +	struct clk_hw	clk480m_hw;
> +	struct regulator	*vbus_host;
> +	const struct rockchip_usb2phy_cfg	*phy_cfg;
> +	struct rockchip_usb2phy_port	ports[USB2PHY_NUM_PORTS];
> +};
> +
> +static inline int property_enable(struct rockchip_usb2phy *rphy,
> +				  const struct usb2phy_reg *reg, bool en)
> +{
> +	unsigned int val, mask, tmp;
> +
> +	tmp = en ? reg->enable : reg->disable;
> +	mask = GENMASK(reg->bitend, reg->bitstart);
> +	val = (tmp << reg->bitstart) | (mask << BIT_WRITEABLE_SHIFT);
> +
> +	return regmap_write(rphy->grf, reg->offset, val);
> +}
> +
> +static inline bool property_enabled(struct rockchip_usb2phy *rphy,
> +				    const struct usb2phy_reg *reg)
> +{
> +	int ret;
> +	unsigned int tmp, orig;
> +	unsigned int mask = GENMASK(reg->bitend, reg->bitstart);
> +
> +	ret = regmap_read(rphy->grf, reg->offset, &orig);
> +	if (ret)
> +		return false;
> +
> +	tmp = (orig & mask) >> reg->bitstart;
> +	return tmp == reg->enable;
> +}
> +
> +static int rockchip_usb2phy_clk480m_enable(struct clk_hw *hw)
> +{
> +	struct rockchip_usb2phy *rphy =
> +		container_of(hw, struct rockchip_usb2phy, clk480m_hw);
> +	int ret = 0;
> +
> +	/* turn on 480m clk output if it is off */
> +	if (!property_enabled(rphy, &rphy->phy_cfg->clkout_ctl)) {
> +		ret = property_enable(rphy, &rphy->phy_cfg->clkout_ctl, true);
> +		if (ret)
> +			return ret;
> +
> +		/* waitting for the clk become stable */
> +		mdelay(1);
> +	}
> +
> +	return ret;
> +}
> +
> +static void rockchip_usb2phy_clk480m_disable(struct clk_hw *hw)
> +{
> +	struct rockchip_usb2phy *rphy =
> +		container_of(hw, struct rockchip_usb2phy, clk480m_hw);
> +
> +	/* turn off 480m clk output */
> +	property_enable(rphy, &rphy->phy_cfg->clkout_ctl, false);
> +}
> +
> +static int rockchip_usb2phy_clk480m_enabled(struct clk_hw *hw)
> +{
> +	struct rockchip_usb2phy *rphy =
> +		container_of(hw, struct rockchip_usb2phy, clk480m_hw);
> +
> +	return property_enabled(rphy, &rphy->phy_cfg->clkout_ctl);
> +}
> +
> +static unsigned long
> +rockchip_usb2phy_clk480m_recalc_rate(struct clk_hw *hw,
> +				     unsigned long parent_rate)
> +{
> +	return 480000000;
> +}
> +
> +static const struct clk_ops rockchip_usb2phy_clkout_ops = {
> +	.enable = rockchip_usb2phy_clk480m_enable,
> +	.disable = rockchip_usb2phy_clk480m_disable,
> +	.is_enabled = rockchip_usb2phy_clk480m_enabled,
> +	.recalc_rate = rockchip_usb2phy_clk480m_recalc_rate,
> +};
> +
> +static void rockchip_usb2phy_clk480m_unregister(void *data)
> +{
> +	struct rockchip_usb2phy *rphy = data;
> +
> +	of_clk_del_provider(rphy->dev->of_node);
> +	clk_unregister(rphy->clk480m);
> +}
> +
> +static struct clk *
> +rockchip_usb2phy_clk480m_register(struct rockchip_usb2phy *rphy)
> +{
> +	struct device_node *node = rphy->dev->of_node;
> +	struct clk *clk;
> +	struct clk_init_data init;
> +	int ret;
> +
> +	init.name = "clk_usbphy_480m";
> +	init.ops = &rockchip_usb2phy_clkout_ops;
> +	init.flags = CLK_IS_ROOT;

One more comment:

include/linux/clk-provider.h:#define CLK_IS_ROOT                BIT(4) /* Deprecated: Don't use */

... and the definition has been removed in linux-next.

Guenter