[PATCH v7 3/5] usb: dwc3: make usb2 phy utmi interface configurable in DT

[William.wu]

Dear Rob,


On 2016/7/17 6:57, Rob Herring wrote:
> On Thu, Jul 14, 2016 at 04:59:20PM +0800, William Wu wrote:
>> Add snps,phyif-utmi-width devicetree property to configure
>> the UTMI+ PHY with an 8- or 16-bit interface. UTMI+ PHY
>> interface is a hardware property, and it's platform dependent.
>> Normally,the PHYIF can be configured during coreconsultant.
>             ^
> space
I'll fix it next patch, thanks:-)
>
>> But for some specific USB cores(e.g. rk3399 SoC DWC3), the
>> default PHYIF configuration value is fault, so we need to
>> reconfigure it by software.
>>
>> And refer to the DWC3 databook, the GUSB2PHYCFG.USBTRDTIM
>> must be set to the corresponding value according to the
>> UTMI+ PHY interface.
>>
>> Signed-off-by: William Wu <william.wu at rock-chips.com>
>> ---
>> Changes in v7:
>> - remove quirk and use only one property to configure utmi (Heiko, Rob Herring)
>>
>> Changes in v6:
>> - use '-' instead of '_' in dts (Rob Herring)
>>
>> Changes in v5:
>> - None
>>
>> Changes in v4:
>> - rebase on top of balbi testing/next, remove pdata (balbi)
>>
>> Changes in v3:
>> - None
>>
>> Changes in v2:
>> - add a quirk for phyif_utmi (balbi)
>>
>>   Documentation/devicetree/bindings/usb/dwc3.txt |  3 +++
>>   drivers/usb/dwc3/core.c                        | 25 +++++++++++++++++++++++++
>>   drivers/usb/dwc3/core.h                        | 10 ++++++++++
>>   3 files changed, 38 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
>> index 020b0e9..00cc541 100644
>> --- a/Documentation/devicetree/bindings/usb/dwc3.txt
>> +++ b/Documentation/devicetree/bindings/usb/dwc3.txt
>> @@ -47,6 +47,9 @@ Optional properties:
>>    - snps,hird-threshold: HIRD threshold
>>    - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for
>>      UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3.
>> + - snps,phyif-utmi-width: the value to configure the core to support a UTMI+ PHY
>> +			with an 8- or 16-bit interface. Value 8 select 8-bit
>> +			interface, value 16 select 16-bit interface.
> Is 'phy_type = "utmi_wide"' not the same as 16-bit width?
>
> Again, I think this should be common.
Yes， I agree with you. ‘phy_type = "utmi_wide" really means 16-bit UTMI 
width.
Thanks very much for your rigorous check.

And according to Heiko's helpful suggestion，I double check the kernel 
code and
look over UTMI/UTMI+ spec，I confirm that there is already generic code in
drivers/usb/phy/of.c about utmi interface, 'phy_type = "utmi"' means 
8-bit interface,
and 'phy_type = "utmi_wide"' means 16-bit interface.

So I think I don't need to add a new dts property 
'snps,phyif-utmi-width' here，
but just use the‘phy_type’ property to confirm UTMI+ interface for dwc3.

>
> Rob
>
>
>