[PATCH] ARM: dts: add rk3288-firefly-reload

Randy Li ayaka at soulik.info
Sun Jul 17 08:38:57 PDT 2016


The Firefly RK3288 Reload is a combination Firefly rk3288 core board
with the Reload baseboard. Add a dtsi for the Firefly rk3288 core
which can be included into the dts for the various baseboards
in the future and dts for Reload base board.

Currently supported are serial console, wired networking, eMMC and
SD storage, SPFIF, IR receiver, LEDs, SDIO wifi and USB. But only
the OTG could work on the host mode now, the other USB host can't
work now, additional patches are required.

Signed-off-by: Randy Li <ayaka at soulik.info>
---
 Documentation/devicetree/bindings/arm/rockchip.txt |   4 +
 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi  | 304 ++++++++++++++++++++
 arch/arm/boot/dts/rk3288-firefly-reload.dts        | 320 +++++++++++++++++++++
 4 files changed, 629 insertions(+)
 create mode 100644 arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi
 create mode 100644 arch/arm/boot/dts/rk3288-firefly-reload.dts

diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index 715d960..3380212c 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -31,6 +31,10 @@ Rockchip platforms device tree bindings
     or
       - compatible = "firefly,firefly-rk3288-beta", "rockchip,rk3288";
 
+- Firefly Firefly-RK3288 Reload board:
+    Required root node properties:
+      - compatible = "firefly,firefly-rk3288-reload", "rockchip,rk3288";
+
 - ChipSPARK PopMetal-RK3288 board:
     Required root node properties:
       - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 414b427..8173e77 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -606,6 +606,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
 	rk3288-evb-rk808.dtb \
 	rk3288-firefly-beta.dtb \
 	rk3288-firefly.dtb \
+	rk3288-firefly-reload.dtb \
 	rk3288-miqi.dtb \
 	rk3288-popmetal.dtb \
 	rk3288-r89.dtb \
diff --git a/arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi b/arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi
new file mode 100644
index 0000000..039ae16
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi
@@ -0,0 +1,304 @@
+/*
+ * Device tree file for Firefly Rockchip RK3288 Core board
+ * Copyright (c) 2016 Randy Li <ayaka at soulik.info>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include <dt-bindings/input/input.h>
+#include "rk3288.dtsi"
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0 0x80000000>;
+	};
+
+	dovdd_1v8: dovdd-1v8-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "dovdd_1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc28_dvp>;
+	};
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+	};
+
+	io_domains: io-domains {
+		compatible = "rockchip,rk3288-io-voltage-domain";
+		rockchip,grf = <&grf>;
+
+		audio-supply = <&vcca_33>;
+		bb-supply = <&vcc_io>;
+		dvp-supply = <&dovdd_1v8>;
+		flash0-supply = <&vcc_flash>;
+		flash1-supply = <&vcc_lan>;
+		gpio30-supply = <&vcc_io>;
+		gpio1830-supply = <&vcc_io>;
+		lcdc-supply = <&vcc_io>;
+		sdcard-supply = <&vccio_sd>;
+		wifi-supply = <&vccio_wl>;
+	};
+
+	vbat_wl: vcc_sys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_flash: flash-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_flash";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc_5v: usb-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	disable-wp;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_pwr>, <&emmc_bus8>;
+	vmmc-supply = <&vcc_io>;
+	vqmmc-supply = <&vcc_flash>;
+	status = "okay";
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	clock_in_out = "input";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>, <&phy_rst>, <&phy_pmeb>, <&phy_int>;
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "ok";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	vdd_cpu: syr827 at 40 {
+		compatible = "silergy,syr827";
+		fcs,suspend-voltage-selector = <1>;
+		reg = <0x40>;
+		regulator-name = "vdd_cpu";
+		regulator-min-microvolt = <850000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-enable-ramp-delay = <300>;
+		regulator-ramp-delay = <8000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vdd_gpu: syr828 at 41 {
+		compatible = "silergy,syr828";
+		fcs,suspend-voltage-selector = <1>;
+		reg = <0x41>;
+		regulator-name = "vdd_gpu";
+		regulator-min-microvolt = <850000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	act8846: act8846 at 5a {
+		compatible = "active-semi,act8846";
+		reg = <0x5a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_vsel>, <&pwr_hold>;
+		system-power-controller;
+
+		vp1-supply = <&vcc_sys>;
+		vp2-supply = <&vcc_sys>;
+		vp3-supply = <&vcc_sys>;
+		vp4-supply = <&vcc_sys>;
+		inl1-supply = <&vcc_sys>;
+		inl2-supply = <&vcc_sys>;
+		inl3-supply = <&vcc_20>;
+
+		regulators {
+			vcc_ddr: REG1 {
+				regulator-name = "vcc_ddr";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			vcc_io: REG2 {
+				regulator-name = "vcc_io";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_log: REG3 {
+				regulator-name = "vdd_log";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			vcc_20: REG4 {
+				regulator-name = "vcc_20";
+				regulator-min-microvolt = <2000000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-always-on;
+			};
+
+			vccio_sd: REG5 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd10_lcd: REG6 {
+				regulator-name = "vdd10_lcd";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			vcca_33: REG7  {
+				regulator-name = "vcca_33";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vcc_lan: REG8 {
+				regulator-name = "vcca_lan";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vccio_pmu: REG9 {
+				regulator-name = "vccio_pmu";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vdd_10: REG10 {
+				regulator-name = "vdd_10";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			vccio_wl: vcc_18: REG11 {
+				regulator-name = "vcc_18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			vcc18_lcd: REG12 {
+				regulator-name = "vcc18_lcd";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&pinctrl {
+	pcfg_output_high: pcfg-output-high {
+		output-high;
+	};
+
+	pcfg_output_low: pcfg-output-low {
+		output-low;
+	};
+
+	pcfg_pull_up_drv_12ma: pcfg-pull-up-drv-12ma {
+		bias-pull-up;
+		drive-strength = <12>;
+	};
+
+	act8846 {
+		pwr_hold: pwr-hold {
+			rockchip,pins = <0 1 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+
+		pmic_vsel: pmic-vsel {
+			rockchip,pins = <7 14 RK_FUNC_GPIO &pcfg_output_low>;
+		};
+	};
+
+	gmac {
+		phy_int: phy-int {
+			rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		phy_pmeb: phy-pmeb {
+			rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		phy_rst: phy-rst {
+			rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+	};
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <0>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/rk3288-firefly-reload.dts b/arch/arm/boot/dts/rk3288-firefly-reload.dts
new file mode 100644
index 0000000..8adda0a
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-firefly-reload.dts
@@ -0,0 +1,320 @@
+/*
+ * Device tree file for Firefly Rockchip RK3288 Reload base board
+ * Copyright (c) 2016 Randy Li <ayaka at soulik.info>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/dts-v1/;
+#include "rk3288-firefly-reload-core.dtsi"
+
+/ {
+	model = "Firefly-RK3288-reload";
+	compatible = "firefly,firefly-rk3288-reload", "rockchip,rk3288";
+
+	leds {
+		compatible = "gpio-leds";
+
+		power {
+			gpios = <&gpio8 2 GPIO_ACTIVE_LOW>;
+			label = "firefly:blue:power";
+			pinctrl-names = "default";
+			pinctrl-0 = <&power_led>;
+			panic-indicator;
+		};
+
+		work {
+			gpios = <&gpio8 1 GPIO_ACTIVE_LOW>;
+			label = "firefly:blue:user";
+			linux,default-trigger = "rc-feedback";
+			pinctrl-names = "default";
+			pinctrl-0 = <&work_led>;
+		};
+	};
+	
+	vcc_sd: sdmmc-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc_pwr>;
+		regulator-name = "vcc_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&hym8563>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable>;
+		reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
+	};
+
+	vcc_host_5v: usb-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&host_vbus_drv>;
+		regulator-name = "vcc_host_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&vcc_5v>;
+	};
+
+	vcc_otg_5v: usb-otg-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&otg_vbus_drv>;
+		regulator-name = "vcc_otg_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&vcc_5v>;
+	};
+
+	/*
+	 * A TT8142 creates both dovdd_1v8 and vcc28_dvp, controlled
+	 * by the dvp_pwr pin.
+	 */
+	vcc28_dvp: vcc28-dvp-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dvp_pwr>;
+		regulator-name = "vcc28_dvp";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+		vin-supply = <&vcc_io>;
+	};
+
+	ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		power {
+			wakeup-source;
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+			label = "GPIO Power";
+			linux,code = <KEY_POWER>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pwr_key>;
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "SPDIF";
+		simple-audio-card,dai-link at 1 {  /* S/PDIF - S/PDIF */
+			cpu { sound-dai = <&spdif>; };
+			codec { sound-dai = <&spdif_out>; };
+		};
+	};
+
+	spdif_out: spdif-out {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+};
+
+&i2c0 {
+	hym8563: hym8563 at 51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xin32k";
+		interrupt-parent = <&gpio7>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&rtc_int>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	codec: es8328 at 10 {
+		compatible = "everest,es8328";
+		DVDD-supply = <&vcca_33>;
+		AVDD-supply = <&vcca_33>;
+		PVDD-supply = <&vcca_33>;
+		HPVDD-supply = <&vcca_33>;
+		clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>;
+		clock-names = "i2s_hclk", "i2s_clk";
+		reg = <0x10>;
+	};
+};
+
+&i2s {
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	sd-uhs-ddr50;
+	card-detect-delay = <200>;
+	disable-wp;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>;
+	vmmc-supply = <&vcc_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&sdio0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-ddr50;
+	cap-sdio-irq;
+	disable-wp;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio0_bus4>, <&sdio0_cmd>, <&sdio0_clk>, <&sdio0_int>;
+	vmmc-supply = <&vbat_wl>;
+	vqmmc-supply = <&vccio_wl>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>;
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&usb_host1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usbhub_rst>;
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+};
+
+&spdif {
+	status = "okay";
+};
+
+&pinctrl {
+	ir {
+		ir_int: ir-int {
+			rockchip,pins = <7 0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	dvp {
+		dvp_pwr: dvp-pwr {
+			rockchip,pins = <0 11 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	hym8563 {
+		rtc_int: rtc-int {
+			rockchip,pins = <7 4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	keys {
+		pwr_key: pwr-key {
+			rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	leds {
+		power_led: power-led {
+			rockchip,pins = <8 2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		work_led: work-led {
+			rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdmmc {
+		/*
+		 * Default drive strength isn't enough to achieve even
+		 * high-speed mode on firefly board so bump up to 12ma.
+		 */
+		sdmmc_bus4: sdmmc-bus4 {
+			rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+					<6 17 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+					<6 18 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+					<6 19 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
+		};
+
+		sdmmc_clk: sdmmc-clk {
+			rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_12ma>;
+		};
+
+		sdmmc_cmd: sdmmc-cmd {
+			rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
+		};
+
+		sdmmc_pwr: sdmmc-pwr {
+			rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdio {
+		wifi_enable: wifi-enable {
+			rockchip,pins = <4 28 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb_host {
+		host_vbus_drv: host-vbus-drv {
+			rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		usbhub_rst: usbhub-rst {
+			rockchip,pins = <8 3 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+	};
+
+	usb_otg {
+		otg_vbus_drv: otg-vbus-drv {
+			rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
-- 
2.7.4




More information about the Linux-rockchip mailing list