[PATCH v2 2/2] phy: add a driver for the Rockchip SoC internal eMMC PHY
Kishon Vijay Abraham I
kishon at ti.com
Sun Jan 31 22:03:43 PST 2016
On Monday 25 January 2016 01:19 PM, Shawn Lin wrote:
> Hello Kishon,
>
> Any changce to apply this patch? :)
back from vacation. Will review it this week. Sorry for the delay.
Thanks
Kishon
>
> On 2016/1/5 9:08, Shawn Lin wrote:
>> This patch to add a generic PHY driver for ROCKCHIP eMMC PHY.
>> Access the PHY via registers provided by GRF (general register
>> files) module.
>>
>> Signed-off-by: Shawn Lin <shawn.lin at rock-chips.com>
>>
>> ---
>>
>> Changes in v2:
>> - remove phy from rockchip_emmc_phy
>> - remove state from rockchip_emmc_phy
>> - remove on/off from init/exit
>>
>> drivers/phy/Kconfig | 7 ++
>> drivers/phy/Makefile | 1 +
>> drivers/phy/phy-rockchip-emmc.c | 241 ++++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 249 insertions(+)
>> create mode 100644 drivers/phy/phy-rockchip-emmc.c
>>
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index 03cb3ea..47d16e3 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -320,6 +320,13 @@ config PHY_ROCKCHIP_USB
>> help
>> Enable this to support the Rockchip USB 2.0 PHY.
>>
>> +config PHY_ROCKCHIP_EMMC
>> + tristate "Rockchip EMMC PHY Driver"
>> + depends on ARCH_ROCKCHIP && OF
>> + select GENERIC_PHY
>> + help
>> + Enable this to support the Rockchip EMMC PHY.
>> +
>> config PHY_ST_SPEAR1310_MIPHY
>> tristate "ST SPEAR1310-MIPHY driver"
>> select GENERIC_PHY
>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>> index 075db1a..ed8f175 100644
>> --- a/drivers/phy/Makefile
>> +++ b/drivers/phy/Makefile
>> @@ -35,6 +35,7 @@ phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2) +=
>> phy-s5pv210-usb2.o
>> obj-$(CONFIG_PHY_EXYNOS5_USBDRD) += phy-exynos5-usbdrd.o
>> obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
>> obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
>> +obj-$(CONFIG_PHY_ROCKCHIP_EMMC) += phy-rockchip-emmc.o
>> obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
>> obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY) += phy-spear1310-miphy.o
>> obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o
>> diff --git a/drivers/phy/phy-rockchip-emmc.c b/drivers/phy/phy-rockchip-emmc.c
>> new file mode 100644
>> index 0000000..6a157c2
>> --- /dev/null
>> +++ b/drivers/phy/phy-rockchip-emmc.c
>> @@ -0,0 +1,241 @@
>> +/*
>> + * Rockchip emmc PHY driver
>> + *
>> + * Copyright (C) 2015 Shawn Lin <shawn.lin at rock-chips.com>
>> + * Copyright (C) 2015 ROCKCHIP, Inc.
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License as published by
>> + * the Free Software Foundation; either version 2 of the License.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#include <linux/delay.h>
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/of_address.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/regmap.h>
>> +
>> +/*
>> + * The higher 16-bit of this register is used for write protection
>> + * only if BIT(x + 16) set to 1 the BIT(x) can be written.
>> + */
>> +#define HIWORD_UPDATE(val, mask, shift) \
>> + ((val) << (shift) | (mask) << ((shift) + 16))
>> +
>> +/* Register definition */
>> +#define GRF_EMMCPHY_CON0 0x0
>> +#define GRF_EMMCPHY_CON1 0x4
>> +#define GRF_EMMCPHY_CON2 0x8
>> +#define GRF_EMMCPHY_CON3 0xc
>> +#define GRF_EMMCPHY_CON4 0x10
>> +#define GRF_EMMCPHY_CON5 0x14
>> +#define GRF_EMMCPHY_CON6 0x18
>> +#define GRF_EMMCPHY_STATUS 0x20
>> +
>> +#define PHYCTRL_PDB_MASK 0x1
>> +#define PHYCTRL_PDB_SHIFT 0x0
>> +#define PHYCTRL_PDB_PWR_ON 0x1
>> +#define PHYCTRL_PDB_PWR_OFF 0x0
>> +#define PHYCTRL_ENDLL_MASK 0x1
>> +#define PHYCTRL_ENDLL_SHIFT 0x1
>> +#define PHYCTRL_ENDLL_ENABLE 0x1
>> +#define PHYCTRL_ENDLL_DISABLE 0x0
>> +#define PHYCTRL_CALDONE_MASK 0x1
>> +#define PHYCTRL_CALDONE_SHIFT 0x6
>> +#define PHYCTRL_CALDONE_DONE 0x1
>> +#define PHYCTRL_CALDONE_GOING 0x0
>> +#define PHYCTRL_DLLRDY_MASK 0x1
>> +#define PHYCTRL_DLLRDY_SHIFT 0x5
>> +#define PHYCTRL_DLLRDY_DONE 0x1
>> +#define PHYCTRL_DLLRDY_GOING 0x0
>> +
>> +struct rockchip_emmc_phy {
>> + unsigned int reg_offset;
>> + struct regmap *reg_base;
>> +};
>> +
>> +static int rockchip_emmc_phy_power(struct rockchip_emmc_phy *rk_phy,
>> + bool on_off)
>> +{
>> + unsigned int caldone;
>> + unsigned int dllrdy;
>> +
>> + /*
>> + * Keep phyctrl_pdb and phyctrl_endll low to allow
>> + * initialization of CALIO state M/C DFFs
>> + */
>> + regmap_write(rk_phy->reg_base,
>> + rk_phy->reg_offset + GRF_EMMCPHY_CON6,
>> + HIWORD_UPDATE(PHYCTRL_PDB_PWR_OFF,
>> + PHYCTRL_PDB_MASK,
>> + PHYCTRL_PDB_SHIFT));
>> + regmap_write(rk_phy->reg_base,
>> + rk_phy->reg_offset + GRF_EMMCPHY_CON6,
>> + HIWORD_UPDATE(PHYCTRL_ENDLL_DISABLE,
>> + PHYCTRL_ENDLL_MASK,
>> + PHYCTRL_ENDLL_SHIFT));
>> +
>> + /* Already finish power_off above */
>> + if (on_off == PHYCTRL_PDB_PWR_OFF)
>> + return 0;
>> +
>> + /*
>> + * According to the user manual, calpad calibration
>> + * cycle takes more than 2us without the minimal recommended
>> + * value, so we may need a little margin here
>> + */
>> + udelay(3);
>> + regmap_write(rk_phy->reg_base,
>> + rk_phy->reg_offset + GRF_EMMCPHY_CON6,
>> + HIWORD_UPDATE(PHYCTRL_PDB_PWR_ON,
>> + PHYCTRL_PDB_MASK,
>> + PHYCTRL_PDB_SHIFT));
>> +
>> + /*
>> + * According to the user manual, it asks driver to
>> + * wait 5us for calpad busy trimming
>> + */
>> + udelay(5);
>> + regmap_read(rk_phy->reg_base,
>> + rk_phy->reg_offset + GRF_EMMCPHY_STATUS,
>> + &caldone);
>> + caldone = (caldone >> PHYCTRL_CALDONE_SHIFT) & PHYCTRL_CALDONE_MASK;
>> + if (caldone != PHYCTRL_CALDONE_DONE) {
>> + pr_err("rockchip_emmc_phy_power: caldone timeout.\n");
>> + return -ETIMEDOUT;
>> + }
>> +
>> + /*
>> + * Enable analog DLL circuits, and we need extra 10.2us
>> + * for dll to be ready for work.
>> + */
>> + regmap_write(rk_phy->reg_base,
>> + rk_phy->reg_offset + GRF_EMMCPHY_CON6,
>> + HIWORD_UPDATE(PHYCTRL_ENDLL_ENABLE,
>> + PHYCTRL_ENDLL_MASK,
>> + PHYCTRL_ENDLL_SHIFT));
>> + udelay(11);
>> + regmap_read(rk_phy->reg_base,
>> + rk_phy->reg_offset + GRF_EMMCPHY_STATUS,
>> + &dllrdy);
>> + dllrdy = (dllrdy >> PHYCTRL_DLLRDY_SHIFT) & PHYCTRL_DLLRDY_MASK;
>> + if (dllrdy != PHYCTRL_DLLRDY_DONE) {
>> + pr_err("rockchip_emmc_phy_power: dllrdy timeout.\n");
>> + return -ETIMEDOUT;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int rockchip_emmc_phy_power_off(struct phy *phy)
>> +{
>> + struct rockchip_emmc_phy *rk_phy = phy_get_drvdata(phy);
>> + int ret = 0;
>> +
>> + /* Power down emmc phy analog blocks */
>> + ret = rockchip_emmc_phy_power(rk_phy, PHYCTRL_PDB_PWR_OFF);
>> + if (ret)
>> + return ret;
>> +
>> + return 0;
>> +}
>> +
>> +static int rockchip_emmc_phy_power_on(struct phy *phy)
>> +{
>> + struct rockchip_emmc_phy *rk_phy = phy_get_drvdata(phy);
>> + int ret = 0;
>> +
>> + /* Power up emmc phy analog blocks */
>> + ret = rockchip_emmc_phy_power(rk_phy, PHYCTRL_PDB_PWR_ON);
>> + if (ret)
>> + return ret;
>> +
>> + return 0;
>> +}
>> +
>> +static int rockchip_emmc_phy_init(struct phy *phy)
>> +{
>> + return 0;
>> +}
>> +
>> +static int rockchip_emmc_phy_exit(struct phy *phy)
>> +{
>> + return 0;
>> +}
>> +
>> +static const struct phy_ops ops = {
>> + .init = rockchip_emmc_phy_init,
>> + .exit = rockchip_emmc_phy_exit,
>> + .power_on = rockchip_emmc_phy_power_on,
>> + .power_off = rockchip_emmc_phy_power_off,
>> + .owner = THIS_MODULE,
>> +};
>> +
>> +static int rockchip_emmc_phy_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct rockchip_emmc_phy *rk_phy;
>> + struct phy *generic_phy;
>> + struct phy_provider *phy_provider;
>> + struct regmap *grf;
>> + unsigned int reg_offset;
>> +
>> + grf = syscon_regmap_lookup_by_phandle(dev->of_node, "rockchip,grf");
>> + if (IS_ERR(grf)) {
>> + dev_err(dev, "Missing rockchip,grf property\n");
>> + return PTR_ERR(grf);
>> + }
>> +
>> + rk_phy = devm_kzalloc(dev, sizeof(*rk_phy), GFP_KERNEL);
>> + if (!rk_phy)
>> + return -ENOMEM;
>> +
>> + if (of_property_read_u32(dev->of_node, "reg", ®_offset)) {
>> + dev_err(dev, "missing reg property in node %s\n",
>> + dev->of_node->name);
>> + return -EINVAL;
>> + }
>> +
>> + rk_phy->reg_offset = reg_offset;
>> + rk_phy->reg_base = grf;
>> +
>> + generic_phy = devm_phy_create(dev, dev->of_node, &ops);
>> + if (IS_ERR(generic_phy)) {
>> + dev_err(dev, "failed to create PHY\n");
>> + return PTR_ERR(generic_phy);
>> + }
>> +
>> + phy_set_drvdata(generic_phy, rk_phy);
>> + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
>> +
>> + return PTR_ERR_OR_ZERO(phy_provider);
>> +}
>> +
>> +static const struct of_device_id rockchip_emmc_phy_dt_ids[] = {
>> + { .compatible = "rockchip,rk3399-emmc-phy" },
>> + {}
>> +};
>> +
>> +MODULE_DEVICE_TABLE(of, rockchip_emmc_phy_dt_ids);
>> +
>> +static struct platform_driver rockchip_emmc_driver = {
>> + .probe = rockchip_emmc_phy_probe,
>> + .driver = {
>> + .name = "rockchip-emmc-phy",
>> + .of_match_table = rockchip_emmc_phy_dt_ids,
>> + },
>> +};
>> +
>> +module_platform_driver(rockchip_emmc_driver);
>> +
>> +MODULE_AUTHOR("Shawn Lin <shawn.lin at rock-chips.com>");
>> +MODULE_DESCRIPTION("Rockchip EMMC PHY driver");
>> +MODULE_LICENSE("GPL v2");
>>
>
>
More information about the Linux-rockchip
mailing list