[PATCH v2] pinctrl: rockchip: add support for the rk3399
David.Wu
wdc at rock-chips.com
Fri Jan 29 03:35:23 PST 2016
Hi Heiko,
在 2016/1/29 0:56, Heiko Stübner 写道:
> Hi David,
>
> Am Donnerstag, 7. Januar 2016, 15:41:38 schrieb David Wu:
>> From: David Wu <david.wu at rock-chips.com>
>>
>> The pinctrl of rk3399 is much different from other's,
>> especially the 3bits of drive strength.
>>
>> Signed-off-by: David Wu <david.wu at rock-chips.com>
>> ---
>> change from v1:
>> - need spin_unlock_irqrestore for set drive default case
>>
>> .../bindings/pinctrl/rockchip,pinctrl.txt | 1 +
>> drivers/pinctrl/pinctrl-rockchip.c | 339
>> ++++++++++++++++++++- 2 files changed, 326 insertions(+), 14 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
>> b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt index
>> 391ef4b..3bb9456 100644
>> --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
>> +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
>> @@ -22,6 +22,7 @@ Required properties for iomux controller:
>> - compatible: one of "rockchip,rk2928-pinctrl",
>> "rockchip,rk3066a-pinctrl" "rockchip,rk3066b-pinctrl",
>> "rockchip,rk3188-pinctrl"
>> "rockchip,rk3288-pinctrl", "rockchip,rk3368-pinctrl"
>> + "rockchip,rk3399-pinctrl"
>> - rockchip,grf: phandle referencing a syscon providing the
>> "general register files"
>>
>> diff --git a/drivers/pinctrl/pinctrl-rockchip.c
>> b/drivers/pinctrl/pinctrl-rockchip.c index a065112..9d61c6e 100644
>> --- a/drivers/pinctrl/pinctrl-rockchip.c
>> +++ b/drivers/pinctrl/pinctrl-rockchip.c
> [...]
>
>> @@ -685,19 +821,60 @@ static int rockchip_get_drive_perpin(struct
>> rockchip_pin_bank *bank, struct rockchip_pin_ctrl *ctrl = info->ctrl;
>> struct regmap *regmap;
>> int reg, ret;
>> - u32 data;
>> + u32 data, temp, rmask_bits;
>> u8 bit;
>> + int drv_type = bank->drv[pin_num / 8].drv_type;
>>
>> ctrl->drv_calc_reg(bank, pin_num, ®map, ®, &bit);
>>
>> + switch (drv_type) {
>> + case DRV_TYPE_IO_1V8_3V0_AUTO:
>> + case DRV_TYPE_IO_3V3_ONLY:
>> + if (RK3399_DRV_3BITS_PER_PIN + bit >= 16) {
> According to the doc excerpts, wouldn't the big special handling only be
> necessary for for gpio3b5 alone (+ other banks) ... i.e. the one setting being
> split over both registers?
yes, only the pin5 setting of 3bits width bank is split over two registers.
> If so I think doing something like the following might be easier to
> understand? Same of course for the set-counterpart. [Beware if I missed up the
> indices somewhere :-)
yeap.
Seemed it is clearer to view by using following code.
I will have a try, thanks.
>
> rmask_bits = RK3399_DRV_3BITS_PER_PIN;
> switch(bit) {
> case 0 ... 12:
> /* regular case, nothing to do */
> break;
> case 15:
> /* drive-strength offset is special, as it is spread over 2 registers */
> ret = regmap_read(regmap, reg, &data);
> if (ret)
> return ret;
>
> ret = regmap_read(regmap, reg + 0x4, &temp);
> if (ret)
> return ret;
>
> /*
> * the bit data[15] contains bit 0 of the value
> * while temp[1:0] containts bits 2 and 1
> */
> data >>= 15;
> temp &= 0x3;
> temp <<= 1;
> data |= temp;
>
> return rockchip_perpin_drv_list[drv_type][data];
> case 18 ... 21:
> /* setting fully enclosed in the second register */
> rmask_bits = RK3399_DRV_3BITS_PER_PIN;
> reg += 4;
> bit -= 18;
> }
>
>> + /* need to read regs twice */
>> + ret = regmap_read(regmap, reg, &temp);
>> + if (ret)
>> + return ret;
>> +
>> + temp >>= bit;
>> + rmask_bits = 16 - bit;
>> + temp &= (1 << rmask_bits) - 1;
>> +
>> + reg = reg + 0x4;
>> + ret = regmap_read(regmap, reg, &data);
>> + if (ret)
>> + return ret;
>> +
>> + rmask_bits = RK3399_DRV_3BITS_PER_PIN
>> + + bit - 16;
>> + data &= (1 << rmask_bits) - 1;
>> + data <<= 16 - bit;
>> + data |= temp;
>> +
>> + return rockchip_perpin_drv_list[drv_type][data];
>> + }
>> +
>> + rmask_bits = RK3399_DRV_3BITS_PER_PIN;
>> + break;
>> + case DRV_TYPE_IO_DEFAULT:
>> + case DRV_TYPE_IO_1V8_OR_3V0:
>> + case DRV_TYPE_IO_1V8_ONLY:
>> + rmask_bits = RK3288_DRV_BITS_PER_PIN;
>> + break;
>> + default:
>> + dev_err(info->dev, "unsupported pinctrl drive type: %d\n",
>> + drv_type);
>> + return -EINVAL;
>> + }
>> +
>> ret = regmap_read(regmap, reg, &data);
>> if (ret)
>> return ret;
>>
>> data >>= bit;
>> - data &= (1 << RK3288_DRV_BITS_PER_PIN) - 1;
>> + data &= (1 << rmask_bits) - 1;
>>
>> - return rockchip_perpin_drv_list[data];
>> + return rockchip_perpin_drv_list[drv_type][data];
>> }
>>
>> static int rockchip_set_drive_perpin(struct rockchip_pin_bank *bank,
> [...]
>
>> @@ -729,8 +913,45 @@ static int rockchip_set_drive_perpin(struct
>> rockchip_pin_bank *bank,
>>
>> spin_lock_irqsave(&bank->slock, flags);
>>
>> + switch (drv_type) {
>> + case DRV_TYPE_IO_1V8_3V0_AUTO:
>> + case DRV_TYPE_IO_3V3_ONLY:
>> + if (RK3399_DRV_3BITS_PER_PIN + bit >= 16) {
>> + /* need to write regs twice */
>> + rmask_bits = 16 - bit;
>> + /* enable the write to the equivalent lower bits */
>> + data = ((1 << rmask_bits) - 1) << (bit + 16);
>> + rmask = data | (data >> 16);
>> + ret &= (1 << rmask_bits) - 1;
>> + data |= (ret << bit);
>> +
>> + ret = regmap_update_bits(regmap, reg, rmask, data);
>> + if (ret)
>> + return ret;
>> +
>> + ret = i >> rmask_bits;
>> + rmask_bits = RK3399_DRV_3BITS_PER_PIN + bit - 16;
>> + reg = reg + 0x4;
>> + bit = 0;
> Apart from a change similar to the above, should the setting maybe also
> directly return and not depend on the final write?
okay, i will do the simialr change to the above.
>> + } else {
>> + rmask_bits = RK3399_DRV_3BITS_PER_PIN;
>> + }
>> + break;
>> + case DRV_TYPE_IO_DEFAULT:
>> + case DRV_TYPE_IO_1V8_OR_3V0:
>> + case DRV_TYPE_IO_1V8_ONLY:
>> + rmask_bits = RK3288_DRV_BITS_PER_PIN;
>> + break;
>> + default:
>> + spin_unlock_irqrestore(&bank->slock, flags);
>> + dev_err(info->dev, "unsupported pinctrl drive type: %d\n",
>> + drv_type);
>> + return -EINVAL;
>> +
>> + }
>> +
>> /* enable the write to the equivalent lower bits */
>> - data = ((1 << RK3288_DRV_BITS_PER_PIN) - 1) << (bit + 16);
>> + data = ((1 << rmask_bits) - 1) << (bit + 16);
>> rmask = data | (data >> 16);
>> data |= (ret << bit);
>>
> [...]
>
>> @@ -2208,6 +2461,62 @@ static struct rockchip_pin_ctrl rk3368_pin_ctrl = {
>> .drv_calc_reg = rk3368_calc_drv_reg_and_bit,
>> };
>>
>> +static struct rockchip_pin_bank rk3399_pin_banks[] = {
>> + PIN_BANK_IOMUX_DRV_FLAGS_OFFSET(0, 32, "gpio0", IOMUX_SOURCE_PMU,
>> + IOMUX_SOURCE_PMU,
>> + IOMUX_SOURCE_PMU,
>> + IOMUX_SOURCE_PMU,
>> + DRV_TYPE_IO_1V8_ONLY,
>> + DRV_TYPE_IO_1V8_ONLY,
>> + 0,
>> + 0,
> DRV_TYPE_IO_DEFAULT instead of 0 please.
>
>
>
>
More information about the Linux-rockchip
mailing list