[PATCH 2/4] riscv: dts: spacemit: k3-com260-ifx: Add USB nodes

[Jennifer Berringer]

K3 CoM260 IFX uses usb3b for a VL817 hub providing 4x USB 3.0 ports and
usb2_host for Bluetooth through the M.2 E-Key slot.

Signed-off-by: Jennifer Berringer <jberring at redhat.com>
---
 .../riscv/boot/dts/spacemit/k3-com260-ifx.dts | 63 +++++++++++++++++++
 1 file changed, 63 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k3-com260-ifx.dts b/arch/riscv/boot/dts/spacemit/k3-com260-ifx.dts
index a5c08a7a781a9..a4dfa25c837fe 100644
--- a/arch/riscv/boot/dts/spacemit/k3-com260-ifx.dts
+++ b/arch/riscv/boot/dts/spacemit/k3-com260-ifx.dts
@@ -3,6 +3,7 @@
  * Copyright (c) 2026 SpacemiT (Hangzhou) Technology Co. Ltd
  * Copyright (c) 2026 Yixun Lan <dlan at kernel.org>
  */
+#include <dt-bindings/phy/phy.h>
 
 #include "k3-com260.dtsi"
 
@@ -18,6 +19,31 @@ aliases {
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	reg_hub_5v: regulator-usb3-hub-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "USB30_HUB";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&reg_5v_sys>;
+	};
+
+	reg_vbus_5v: regulator-usb3-vbus-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "USB30_VBUS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_5v_sys>;
+		gpio = <&gpio K3_GPIO(67) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&combophy {
+	spacemit,apmu = <&syscon_apmu 0x14>;
+	status = "okay";
 };
 
 &i2c1 {
@@ -35,6 +61,43 @@ eeprom at 50 {
 	};
 };
 
+&usb2_host {
+	status = "okay";
+};
+
+&usb2_phy {
+	status = "okay";
+};
+
+&usb3b {
+	phys = <&usb3b_u2phy>, <&combophy 2 PHY_TYPE_USB3>;
+	phy-names = "usb2-phy", "usb3-phy";
+	status = "okay";
+	vbus-supply = <&reg_vbus_5v>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hub_2_0: hub at 1 {
+		compatible = "usb2109,2817";
+		reg = <1>;
+		vdd-supply = <&reg_hub_5v>;
+		peer-hub = <&hub_3_0>;
+		reset-gpios = <&gpio K3_GPIO(53) GPIO_ACTIVE_LOW>;
+	};
+
+	hub_3_0: hub at 2 {
+		compatible = "usb2109,817";
+		reg = <2>;
+		vdd-supply = <&reg_hub_5v>;
+		peer-hub = <&hub_2_0>;
+		reset-gpios = <&gpio K3_GPIO(53) GPIO_ACTIVE_LOW>;
+	};
+};
+
+&usb3b_u2phy {
+	status = "okay";
+};
+
 &sdhci0 {
 	pinctrl-names = "default","uhs";
 	pinctrl-0 = <&mmc1_cfg>;
-- 
2.55.0