[PATCH v7 6/6] PCI: spacemit-k1: Add Spacemit K3 PCIe host controller support

[Inochi Amaoto]

On Sun, Oct 18, 2026 at 06:05:39PM +0530, Manivannan Sadhasivam wrote:
> On 2026-09-29 16:37 +0800, Inochi Amaoto wrote:
> > The PCIe controller on Spacemit K3 is almost a standard Synopsys
> > DesignWare PCIe IP with extra link and reset control. Unlike
> > the PCIe controller on K1, this controller supports external MSI
> > interrupt controller and can use multiple PHYs at the same time.
> > 
> > Add driver to support PCIe controller on Spacemit K3 PCIe.
> > 
> > Signed-off-by: Inochi Amaoto <inochiama at gmail.com>
> > ---
> >  drivers/pci/controller/dwc/Kconfig            |   4 +-
> >  drivers/pci/controller/dwc/pcie-spacemit-k1.c | 139 ++++++++++++++++++
> >  2 files changed, 141 insertions(+), 2 deletions(-)
> > 
> > diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
> > index dcfbe7e229fd..f9c27165260e 100644
> > --- a/drivers/pci/controller/dwc/Kconfig
> > +++ b/drivers/pci/controller/dwc/Kconfig
> > @@ -443,7 +443,7 @@ config PCIE_SOPHGO_DW
> >  	  Sophgo SoCs.
> >  
> >  config PCIE_SPACEMIT_K1
> > -	tristate "SpacemiT K1 PCIe controller (host mode)"
> > +	tristate "SpacemiT PCIe controller (host mode)"
> >  	depends on ARCH_SPACEMIT || COMPILE_TEST
> >  	depends on HAS_IOMEM
> >  	select PCIE_DW_HOST
> > @@ -451,7 +451,7 @@ config PCIE_SPACEMIT_K1
> >  	default ARCH_SPACEMIT
> >  	help
> >  	  Enables support for the DesignWare based PCIe controller in
> > -	  the SpacemiT K1 SoC operating in host mode.  Three controllers
> > +	  the SpacemiT SoC operating in host mode. Three controllers
> >  	  are available on the K1 SoC; the first of these shares a PHY
> >  	  with a USB 3.0 host controller (one or the other can be used).
> >  
> > diff --git a/drivers/pci/controller/dwc/pcie-spacemit-k1.c b/drivers/pci/controller/dwc/pcie-spacemit-k1.c
> > index ec59ccb710ec..61b430f2294a 100644
> > --- a/drivers/pci/controller/dwc/pcie-spacemit-k1.c
> > +++ b/drivers/pci/controller/dwc/pcie-spacemit-k1.c
> > @@ -28,8 +28,18 @@
> >  #define SMLH_LINK_UP			BIT(1)
> >  #define RDLH_LINK_UP			BIT(12)
> >  
> > +#define INTR_STATUS				0x0010
> > +
> >  #define INTR_ENABLE				0x0014
> >  #define MSI_CTRL_INT			BIT(11)
> > +#define RDLH_LINK_UP_INT		BIT(20)
> > +
> > +#define K3_PHY_AHB_IRQSTATUS_INTX		0x0008
> > +
> > +#define K3_ADDR_INTR_STATUS1			0x0018
> > +
> > +#define K3_CACHE_MSTR_AWCACHE_MODE	GENMASK(14, 11)
> > +#define K3_CACHE_MSTR_AWCACHE_BEHAVIOR	0xf
> >  
> >  /* Some controls require APMU regmap access */
> >  #define SYSCON_APMU			"spacemit,apmu"
> > @@ -44,6 +54,9 @@
> >  
> >  #define PCIE_CONTROL_LOGIC			0x0004
> >  #define PCIE_SOFT_RESET			BIT(0)
> > +#define PCIE_PERSTN_OE			BIT(24)
> > +#define PCIE_PERSTN_OUT			BIT(25)
> > +#define PCIE_IGNORE_PERSTN		BIT(31)
> >  
> >  struct k1_pcie;
> >  
> > @@ -315,6 +328,123 @@ static int k1_pcie_parse_port(struct k1_pcie *k1)
> >  	return ret;
> >  }
> >  
> > +static int k3_pcie_init(struct dw_pcie_rp *pp)
> > +{
> > +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> > +	struct k1_pcie *k1 = to_k1_pcie(pci);
> > +	u32 reset_ctrl = k1->pmu_off + PCIE_CLK_RESET_CONTROL;
> > +	u32 val;
> > +	int ret;
> > +
> > +	regmap_clear_bits(k1->pmu, reset_ctrl, LTSSM_EN);
> > +
> > +	k1_pcie_toggle_soft_reset(k1);
> > +
> > +	/* K3: Set IGNORE_PERSTN and drive PERSTN_OE high (assert reset) */
> > +	regmap_update_bits(k1->pmu, k1->pmu_off + PCIE_CONTROL_LOGIC,
> > +			   PCIE_IGNORE_PERSTN | PCIE_PERSTN_OE | PCIE_PERSTN_OUT,
> > +			   PCIE_IGNORE_PERSTN | PCIE_PERSTN_OE);
> > +
> > +	ret = k1_pcie_enable_resources(k1);
> > +	if (ret)
> > +		goto failed_resources;
> > +
> > +	regmap_set_bits(k1->pmu, reset_ctrl, PCIE_AUX_PWR_DET);
> > +	regmap_clear_bits(k1->pmu, reset_ctrl, APP_HOLD_PHY_RST);
> > +
> > +	ret = phy_bulk_init(k1->phy_count, k1->phys);
> > +	if (ret)
> > +		goto failed_phy_init;
> 
> You got me confused with this PHY bulk API for a moment. I think you are trying
> to control all the PHYs of the multi-port RC setup at once. But I believe
> that's not what we want mostly. Each port is an independent entity with its own
> PHY, PERST# etc... So the RC driver controlling all the PHYs at once, doesn't
> seem logical.
> 

In fact this thing is different. Accoring to statement from spacemit, 
for software, it does not need to care about how the phy topology, 
and which phy/phys is/are attached to the RC. It just needs to enable
all the phy and configure the APMU, which is the one that give some
control on PERST# and others. The phy itself does nothing on this.

Regards,
Inochi