[PATCH 2/2] riscv: dts: anlogic: drop unused DR1V90 external clocks

[Brian Masney]

Hi Conor,

On Fri, Oct 02, 2026 at 08:09:08AM +0100, Conor Dooley wrote:
> On Fri, Oct 02, 2026 at 02:07:01PM +0800, Junhui Liu wrote:
> > The external CAN and watchdog clock inputs are not routed on the MLKPAI
> > FS01, the only board currently supported. Drop the two fixed-clock
> > placeholders from the common dtsi, as fixed clocks require a valid
> > clock-frequency property.
> > 
> > Both clock muxes select their internal parent clocks after reset, so
> > the CRU operates correctly without the external inputs. Keep only the
> > required oscillator input to the CRU.
> > 
> > A board using these external clocks should define them in its own
> > board-level dts and override the clocks and clock-names properties of
> > the CRU node.
> > 
> > Reported-by: Yixun Lan <dlan at kernel.org>
> > Fixes: 7849521aaac2 ("riscv: dts: anlogic: add clocks and CRU for DR1V90")
> 
> Uh, why is this in linux next?
> 
> Brian, please don't apply dts patches to the clock (or any other) driver
> tree in the future.

OK, sorry. I just checked clk-next and this is the only dts that I
applied. I'll rebase clk-next and drop this so that the tree only
contains the drivers.

Brian

> 
> Patch itself makes total sense,
> Reviewed-by: Conor Dooley <conor.dooley at microchip.com>
> and because it's easier
> Acked-by: Conor Dooley <conor.dooley at microchip.com>
> 
> > Signed-off-by: Junhui Liu <junhui.liu at pigmoral.tech>
> > ---
> >  arch/riscv/boot/dts/anlogic/dr1v90.dtsi | 16 ++--------------
> >  1 file changed, 2 insertions(+), 14 deletions(-)
> > 
> > diff --git a/arch/riscv/boot/dts/anlogic/dr1v90.dtsi b/arch/riscv/boot/dts/anlogic/dr1v90.dtsi
> > index 574c6608aef0..fe85d01563ad 100644
> > --- a/arch/riscv/boot/dts/anlogic/dr1v90.dtsi
> > +++ b/arch/riscv/boot/dts/anlogic/dr1v90.dtsi
> > @@ -44,23 +44,11 @@ cpu0_intc: interrupt-controller {
> >  	};
> >  
> >  	clocks {
> > -		can_ext: clock-ext-can {
> > -			compatible = "fixed-clock";
> > -			clock-output-names = "can_ext";
> > -			#clock-cells = <0>;
> > -		};
> > -
> >  		osc: clock-osc {
> >  			compatible = "fixed-clock";
> >  			clock-output-names = "osc";
> >  			#clock-cells = <0>;
> >  		};
> > -
> > -		wdt_ext: clock-ext-wdt {
> > -			compatible = "fixed-clock";
> > -			clock-output-names = "wdt_ext";
> > -			#clock-cells = <0>;
> > -		};
> >  	};
> >  
> >  	soc {
> > @@ -128,8 +116,8 @@ uart1: serial at f8401000 {
> >  		cru: clock-controller at f8801000 {
> >  			compatible = "anlogic,dr1v90-cru";
> >  			reg = <0x0 0xf8801000 0 0x400>;
> > -			clocks = <&osc>, <&can_ext>, <&wdt_ext>;
> > -			clock-names = "osc", "can_ext", "wdt_ext";
> > +			clocks = <&osc>;
> > +			clock-names = "osc";
> >  			#clock-cells = <1>;
> >  			#reset-cells = <1>;
> >  		};
> > 
> > -- 
> > 2.55.0
> >