[PATCH v3 7/7] riscv: dts: spacemit: k1-bananapi-f3: add SD card support with UHS modes

[Yixun Lan]

Hi Aurelien,

On 21:24 Wed 18 Mar     , Aurelien Jarno wrote:
> Hi,
> 
> On 2026-03-16 15:03, Iker Pedrosa wrote:
> > Add complete SD card controller support with UHS high-speed modes.
> > 
> > - Enable sdhci0 controller with 4-bit bus width
> > - Configure card detect GPIO with inversion
> > - Connect vmmc-supply to buck4 for 3.3V card power
> > - Connect vqmmc-supply to aldo1 for 1.8V/3.3V I/O switching
> > - Add dual pinctrl states for voltage-dependent pin configuration
> > - Support UHS-I SDR25, SDR50, and SDR104 modes
> > 
> > This enables full SD card functionality including high-speed UHS modes
> > for improved performance.
> > 
> > Suggested-by: Anand Moon <linux.amoon at gmail.com>
> > Signed-off-by: Iker Pedrosa <ikerpedrosam at gmail.com>
> > ---
> >  arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts | 23 +++++++++++++++++++++--
> >  1 file changed, 21 insertions(+), 2 deletions(-)
> > 
> > diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
> > index 404b69c47b91f8c37d74a3031dbad0d94a28d1b4..a7d480d01ccc0439dbf456ed5a81f467af68056a 100644
> > --- a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
> > +++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
> > @@ -222,7 +222,7 @@ buck3_1v8: buck3 {
> >  				regulator-always-on;
> >  			};
> >  
> > -			buck4 {
> > +			buck4: buck4 {
> >  				regulator-min-microvolt = <500000>;
> >  				regulator-max-microvolt = <3300000>;
> >  				regulator-ramp-delay = <5000>;
> > @@ -243,7 +243,7 @@ buck6 {
> >  				regulator-always-on;
> >  			};
> >  
> > -			aldo1 {
> > +			aldo1: aldo1 {
> >  				regulator-min-microvolt = <500000>;
> >  				regulator-max-microvolt = <3400000>;
> >  				regulator-boot-on;
> > @@ -369,3 +369,22 @@ hub_3_0: hub at 2 {
> >  		reset-gpios = <&gpio K1_GPIO(124) GPIO_ACTIVE_LOW>;
> >  	};
> >  };
> > +
> > +&sdhci0 {
> > +	pinctrl-names = "default", "state_uhs";
> > +	pinctrl-0 = <&mmc1_cfg>;
> > +	pinctrl-1 = <&mmc1_uhs_cfg>;
> > +	bus-width = <4>;
> > +	cd-gpios = <&gpio K1_GPIO(80) GPIO_ACTIVE_HIGH>;
> > +	cd-inverted;
> 
> Thanks for this driver. Unfortunately, this is not correct for the 
> Banana PI F3. The OrangePi RV2 buffers the signal from the SD card 
> connector through a transistor, inverting the signal. On the Banana PI 
> F3, the signal goes directly to the GPIO, and does not even have a 
> pull-up.
> 
> With the following change, I have been able to get the patchset working 
> as expected:
> 
> diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
> index a7d480d01ccc0..72b0f75f936aa 100644
> --- a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
> +++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
> @@ -375,8 +375,7 @@ &sdhci0 {
>  	pinctrl-0 = <&mmc1_cfg>;
>  	pinctrl-1 = <&mmc1_uhs_cfg>;
>  	bus-width = <4>;
> -	cd-gpios = <&gpio K1_GPIO(80) GPIO_ACTIVE_HIGH>;
> -	cd-inverted;
> +	cd-gpios = <&gpio K1_GPIO(80) (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
Have to mention, to use the pull-up, the patch to support gpio config should be applied
https://lore.kernel.org/r/20260312-k1-gpio-set-config-v1-0-8c3541da16b1@pigmoral.tech

if you don't want to introduce the dependency, add "broken-cd" property
should also workaround this..
>  	no-mmc;
>  	no-sdio;
>  	disable-wp;
> 
> Regards
> Aurelien
> 
> -- 
> Aurelien Jarno                          GPG: 4096R/1DDD8C9B
> aurelien at aurel32.net                     http://aurel32.net

-- 
Yixun Lan (dlan)