[PATCH v2 6/7] riscv: dts: spacemit: k1-orangepi-rv2: add PMIC and power infrastructure

[Yixun Lan]

Hi Trevor, Iker,

On 14:27 Wed 11 Mar     , Trevor Gamblin wrote:
> Hi,
> 
> On 2026-03-09 07:40, Iker Pedrosa wrote:
> > Add Spacemit P1 PMIC configuration and board power infrastructure for
> > voltage regulation support.
> >
> > - Add board power regulators (12V input, 4V rail)
> > - Enable I2C8 for PMIC communication
> > - Configure PMIC with buck4 (vmmc) and aldo1 (vqmmc) regulators
> > - Set up regulator constraints for SD card operation
> >
> > Signed-off-by: Iker Pedrosa <ikerpedrosam at gmail.com>
> > ---
> >   arch/riscv/boot/dts/spacemit/k1-orangepi-rv2.dts | 48 ++++++++++++++++++++++++
> >   1 file changed, 48 insertions(+)
> >
> > diff --git a/arch/riscv/boot/dts/spacemit/k1-orangepi-rv2.dts b/arch/riscv/boot/dts/spacemit/k1-orangepi-rv2.dts
> > index 7b7331cb3c726f11d597f81917f3a3f5fc21e1b9..414b03f5e6480f05f5d7eeaaa0afb4e86425ae36 100644
> > --- a/arch/riscv/boot/dts/spacemit/k1-orangepi-rv2.dts
> > +++ b/arch/riscv/boot/dts/spacemit/k1-orangepi-rv2.dts
> > @@ -19,6 +19,25 @@ aliases {
> >   		ethernet1 = &eth1;
> >   	};
> >   
> > +	reg_dc_in: dc-in-12v {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "dc_in_12v";
> > +		regulator-min-microvolt = <12000000>;
> > +		regulator-max-microvolt = <12000000>;
> > +		regulator-boot-on;
> > +		regulator-always-on;
> > +	};
> > +
> Is this the correct voltage? I don't see a 12V rail in the RV2's 
> datasheet, and the board's specifications only indicate a 5V USB-C input.

Right, this should be fixed. Please note Han submitted one version of basic DT for rv2
which I think that series will go in first

https://lore.kernel.org/r/20260310161853.3900605-1-gaohan@iscas.ac.cn

> > +	reg_vcc_4v: vcc-4v {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "vcc_4v";
> > +		regulator-min-microvolt = <4000000>;
> > +		regulator-max-microvolt = <4000000>;
> > +		regulator-boot-on;
> > +		regulator-always-on;
> > +		vin-supply = <&reg_dc_in>;
> > +	};
> > +
> >   	chosen {
> >   		stdout-path = "serial0";
> >   	};
> > @@ -92,3 +111,32 @@ &uart0 {
> >   	pinctrl-0 = <&uart0_2_cfg>;
> >   	status = "okay";
> >   };
> > +
> > +&i2c8 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&i2c8_cfg>;
> > +	status = "okay";
> > +
> > +	pmic at 41 {
> > +		compatible = "spacemit,p1";
> > +		reg = <0x41>;
> > +		interrupts = <64>;
> > +		vin-supply = <&reg_vcc_4v>;
> > +
> > +		regulators {
> > +			sd_vmmc: buck4 {
I'd suggest name it more generic and add a comment where device reference to it,
since buck4 requested by more than one devices, will make people less confused.
something just like:
			buck4: buck4 {

> > +				regulator-min-microvolt = <500000>;
> > +				regulator-max-microvolt = <3300000>;
> > +				regulator-ramp-delay = <5000>;
> > +				regulator-always-on;
> > +			};
> > +
> > +			sd_vqmmc: aldo1 {
> > +				regulator-min-microvolt = <500000>;
> > +				regulator-max-microvolt = <3400000>;
> > +				regulator-boot-on;
> > +				regulator-always-on;
> > +			};
> > +		};
> > +	};
> > +};
> >
> 

-- 
Yixun Lan (dlan)